@Robbierob1973
If it is not a typo mistake and you are using RecalBox, then, i think that you confused the forums.
RecalBox : https://forum.recalbox.com/

@mitu Thanks for the reply. I apologize, I'm rather new to using RetroPie on Ubuntu. I was just going by what the default value was on the emulator selection screen when you press a button while the ROM is launching.

9247c15c-3e81-4c7c-bd79-bea1c6087614-image.png

I ended up installing lr-mupen64plus-next as you suggested, and the difference is amazing :) This is what I was hoping for. Thanks!

Nevermind, closed ticket, I mistyped one command, sorry. I cannot delete the question.

@TPR or permissions indeed :-) ...

Glad you figured it out. Personally I love Dosbox pure. The way it lets you pick files to execute, then set an autostart is brilliant for first install. And the way it autoconfigures a controller map for a good chunk of games. Quite excellent.

One point to note. On my GPi it looks like I could probably have hard-coded the value to unbind/bind the built in controller. But I felt it was taking a risk it wouldn't work right. So, instead, I use a temp file to pass the value between scripts.

@duglor cool, let me know if you need help!

@biccahobz123 have a look into mitus post. You are in KIDS-Mode and have to change back to normal ;)

@YFZdude I see. Thanks for the info and the tip. But the issue I have, and the reason I wanted for every button to work on d-input, is the fact that both controllers have the same name in switch mode, which is a problem with their wildly different layouts.

Update your EmulationStation package and try again.

@mitu This is just what I was looking for. I performed an update within retropie config and got the same result. couldn't access any setup menu. copying the ROMs and Bios over, but a couple of BIN files wouldn't copy (admin permission required). I guess after I reflash the SD card, this won't be a problem putting all my ROMs back?

@georgeio111 didn't you say:

.. I brought it approx 5 years ago with all games already on it. ..

This is one of the systems we don't support here in the forums - see https://retropie.org.uk/forum/topic/3/read-this-first.

@mitu I was able to set a system variable OS_NAME=RetroPie and re-ran the script from GIT and the install works now. Not 100% fully tested at this point but at least RetroPie sees the “New” controller

Here is the updated config.txt file

pi@retropie:~ $ cat /boot/config.txt # For more options and information see # http://rpf.io/configtxt # Some settings may impact device functionality. See link above for details # uncomment if you get no picture on HDMI for a default "safe" mode #hdmi_safe=1 # uncomment this if your display has a black border of unused pixels visible # and your display can output without overscan #disable_overscan=1 # uncomment the following to adjust overscan. Use positive numbers if console # goes off screen, and negative if there is too much border #overscan_left=16 #overscan_right=16 #overscan_top=16 #overscan_bottom=16 # uncomment to force a console size. By default it will be display's size minus # overscan. #framebuffer_width=1280 #framebuffer_height=720 # uncomment if hdmi display is not detected and composite is being output hdmi_force_hotplug=1 # uncomment to force a specific HDMI mode (this will force VGA) #hdmi_group=1 #hdmi_mode=1 # uncomment to force a HDMI mode rather than DVI. This can make audio work in # DMT (computer monitor) modes #hdmi_drive=2 # uncomment to increase signal to HDMI, if you have interference, blanking, or # no display #config_hdmi_boost=4 # uncomment for composite PAL #sdtv_mode=2 #uncomment to overclock the arm. 700 MHz is the default. #arm_freq=800 # Uncomment some or all of these to enable the optional hardware interfaces #dtparam=i2c_arm=on #dtparam=i2s=on #dtparam=spi=on # Uncomment this to enable infrared communication. #dtoverlay=gpio-ir,gpio_pin=17 #dtoverlay=gpio-ir-tx,gpio_pin=18 # Additional overlays and parameters are documented /boot/overlays/README # Enable audio (loads snd_bcm2835) dtparam=audio=on [pi4] # Enable DRM VC4 V3D driver on top of the dispmanx display stack dtoverlay=vc4-fkms-v3d max_framebuffers=2 [all] #dtoverlay=vc4-fkms-v3d overscan_scale=1 dtoverlay=picade dtparam=audio=off

I’ll give it another whirl, bit I don’t remember that working when I tried it.......thanks. @Crush

@DanTarl

Hi DanTarl - I created a forum account just to thank you for this tip.

I was frustrated by my zero delay encoder going in to disconnect/reconnect loop (led flashing) while using MAME on Ubuntu v22. Adding this to the Grub Linux boot parameters fixed the problem immediately.

The line now looks like this:

GRUB_CMDLINE_LINUX_DEFAULT="quiet splash usbhid.quirks=0x0079:0x0006:0x00000400"

Detailed instructions for editing Ubuntu boot parameters here.

Thanks again - solving this seemed like such a longshot!

Paul