Regarding v4.4

RK1Gaming

sometimes when I play a game, the system locks up. I have an SD Card with OSMC on it, and it runs flawlessly. OSMC also has the same Kernal version, v4.14. So I have no clue what the problem is.

mitu

@rk1gaming Please give more details about your problem and also details about your system - https://retropie.org.uk/forum/topic/3/read-this-first

RK1Gaming

The only way that I can explain this, is this.I plug the power into the Pi, it goes through the boot process and up comes emulation station. I can let it sit there for a while and then choose a system and load a ROM. The rom loads and I can play for a while and then the screen freezes and I cannot do anything, I have to unplug the power and plug it back in again.

The system is a follows:

Raspberry Pi 3 model B+
A 5v 2.5A power adapter
A PDP Afterglow Prismatic wired XBOX ONE controller
Network (WIRED) ethernet
the system is NOT overclocked

mitu

Which Emulator/ROM ? Do you still have access through SSH to the system ? How did you install the system ?

RK1Gaming

The emulator is for Neo-Geo pocket color and the rom was neo cherry master. Not sure what SSH is. I installed the system by formatting the SD card, flashing it with a clean download of the 4.4 image, putting it into the Pi and plugging in the power and letting it do it's thing. I hope this is what you mean.

mitu

@rk1gaming SSH is another method of remotely accesing your PI, over the network - https://retropie.org.uk/docs/SSH/. If your keyboard/screen are frozen, you can still access your system this way and check what's wrong or reboot it.
Does this happen with every game or just a set of ROMs - like the Neo Cherry Master ?

RK1Gaming

it happens with a vast majority of the games. in fact, it has locked up even when installing a package...like for a system emulator.

mitu

@rk1gaming Do you get a lightning bolt at the top of the screen when the freezing happens ?

RK1Gaming

no.

mitu

@rk1gaming Honestly, looks more like a faulty power supply or card, and not software related. Can you post your config.txt file, from the SD card ?

RK1Gaming

Hmmmm, the power supply came with a kit I bought, but the lightning bolt happened when I used the old power supply. And the sd card is kind of old.

config.txt

For more options and information see

http://rpf.io/configtxt

Some settings may impact device functionality. See link above for details

uncomment if you get no picture on HDMI for a default "safe" mode

#hdmi_safe=1

uncomment this if your display has a black border of unused pixels visible

and your display can output without overscan

disable_overscan=1

uncomment the following to adjust overscan. Use positive numbers if console

goes off screen, and negative if there is too much border

#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

uncomment to force a console size. By default it will be display's size minus

overscan.

#framebuffer_width=1280
#framebuffer_height=720

uncomment if hdmi display is not detected and composite is being output

#hdmi_force_hotplug=1

uncomment to force a specific HDMI mode (this will force VGA)

#hdmi_group=1
#hdmi_mode=1

uncomment to force a HDMI mode rather than DVI. This can make audio work in

DMT (computer monitor) modes

#hdmi_drive=2

uncomment to increase signal to HDMI, if you have interference, blanking, or

no display

#config_hdmi_boost=4

uncomment for composite PAL

#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

Uncomment some or all of these to enable the optional hardware interfaces

#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

Uncomment this to enable the lirc-rpi module

#dtoverlay=lirc-rpi

Additional overlays and parameters are documented /boot/overlays/README

Enable audio (loads snd_bcm2835)

dtparam=audio=on
gpu_mem_256=128
gpu_mem_512=256
gpu_mem_1024=256
overscan_scale=1

mitu

Wrap the contents of the file in code tags (````) so it's readable. Doesn't seem you have anything different than the stock image, so I'd try a different SD card just to make sure it's not that.

RK1Gaming

what do you mean, wrap the code tags?

quicksilver

@rk1gaming put four back tics (````) without the parenthesis before and after blocks of code so that it looks like this:

For more options and information see
http://rpf.io/configtxt
Some settings may impact device functionality. See link above for details
uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

uncomment this if your display has a black border of unused pixels visible
and your display can output without overscan
disable_overscan=1

uncomment the following to adjust overscan. Use positive numbers if console
goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

uncomment to force a console size. By default it will be display's size minus
overscan.
#framebuffer_width=1280
#framebuffer_height=720

uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

uncomment to force a HDMI mode rather than DVI. This can make audio work in
DMT (computer monitor) modes
#hdmi_drive=2

uncomment to increase signal to HDMI, if you have interference, blanking, or
no display
#config_hdmi_boost=4

uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi

Additional overlays and parameters are documented /boot/overlays/README
Enable audio (loads snd_bcm2835)
dtparam=audio=on
gpu_mem_256=128
gpu_mem_512=256
gpu_mem_1024=256
overscan_scale=1

RK1Gaming

This post is deleted!

RK1Gaming

I think I have right

# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=on
gpu_mem_256=128
gpu_mem_512=256
gpu_mem_1024=256
overscan_scale=1

mitu

@rk1gaming Surround the text you pasted with four (4) backticks, one separate lines.

RK1Gaming

I just got a brand new SD card and copied the image to it. Pu the card into the Pi, the initial install went fine and so did updating the system. I went to install the first package "DGEN" and it locked up. Why?

mitu

@rk1gaming said in Regarding v4.4:

Why?

You should try determining if your problem is HW related - run a CPU stress program (like https://core-electronics.com.au/tutorials/stress-testing-your-raspberry-pi.html) and see if it still locks up. Locking is usually indicative of inadequate power supply or improper ventilation.

RK1Gaming

I will try that, thank you.