How can I control 2 players with one keyboard (RetroArch)?

rbaker

@TheStrayMongrel I would say that it the problem. I believe that attract mode was an experimental build. You should use the fully updated version. I reckon if you had revealed that at the start, you would be up and running now. You = Adafruit + Attract Mode Build. Me = Ipac + Version 3.8.1

One final thought, have you checked that your config edits are actually being saved?

TheStrayMongrel

@rbaker Unfortunately not, just tried it on a brand spanking new 4.0 image. Install/allocate keys/retroarch.cfg config/setup wifi/transfer 2 games (using lr-fba-next)/reboot... 1 player works fine but nothing on 2... ahhh. Your suggestion really has broken it down to the most basic of fundamentals in regards to troubleshooting the issue... racking my brain to think of what else it might be.

rbaker

@TheStrayMongrel I am out of ideas now. For me, you plug in a keyboard and it is detected. It allows you to configure player 1 only. You then edit the config to add the "extra" keys you desire for player 2. You save and then you must reboot for the changes to take effect. You then have the most basic form of two player controls. I cannot think what you must be doing that is different to me. Is your syntax correct etc?

dankcushions

@TheStrayMongrel said in How can I control 2 players with one keyboard (RetroArch)?:

@rbaker Unfortunately not, just tried it on a brand spanking new 4.0 image. Install/allocate keys/retroarch.cfg config/setup wifi/transfer 2 games (using lr-fba-next)/reboot... 1 player works fine but nothing on 2... ahhh. Your suggestion really has broken it down to the most basic of fundamentals in regards to troubleshooting the issue... racking my brain to think of what else it might be.

what games? IMO you should test on a console 2 player games (snes etc) as there additional complications to consider in the arcade cores.

also you should post your entire /all/retroarch.cfg and /snes/retroarch.cfg ideally.

rbaker

@TheStrayMongrel Try this video from @Floob :

You could remap using the retroarch gui, if you know your keys are working. Then you can go into retroarch.cfg and look at the changes it made for you and compare them against what you did.

TheStrayMongrel

what games? IMO you should test on a console 2 player games (snes etc) as there additional complications to consider in the arcade cores.
also you should post your entire /all/retroarch.cfg and /snes/retroarch.cfg ideally.

Streetfighter 3 and Streetfighter 2 Alpha @dankcushions. That sounds like something worth trying, so will have a crack at it with a snes game tonight (at work now).

also you should post your entire /all/retroarch.cfg and /snes/retroarch.cfg ideally.

Will do, not sure how to post scroll down command line blocks (like rbaker has here) so will look into that, certainly too large to do screen grabs like i have been previously.

@rbaker said in How can I control 2 players with one keyboard (RetroArch)?:

Is your syntax correct etc?

As far as i know. It matched up with the one you posted earlier on this thread... and i have looked over it closely to see if there are any inconsistencies.

Will also check out the video, thanks.

I guess another thing i can to also is fire up mame4all and see if 2 player keyboard registers on that after configuring using the tab menu... at least then I'll know if the issue is confined to lr-... emulators.

Thanks again all. :)

rbaker

@TheStrayMongrel said in How can I control 2 players with one keyboard (RetroArch)?:

not sure how to post scroll down command line blocks

You use markdown: http://commonmark.org/help/

Code blocks are the last one on the list. You use ``` before and after.

TheStrayMongrel

@rbaker said in How can I control 2 players with one keyboard (RetroArch)?:

@TheStrayMongrel said in How can I control 2 players with one keyboard (RetroArch)?:

not sure how to post scroll down command line blocks

You use markdown: http://commonmark.org/help/

Code blocks are the last one on the list. You use ``` before and after.

Great thanks @rbaker will check it out.

Reading futher into it think it might be time i considered 86ing my current setup and buying the Controlblock. Will have a nice powerswitch that way too.

TheStrayMongrel

It works!!!!!! Dumb****ery on my part, syntax error and i neglected to put "num" prior to the numbers 2 and 6 in the player 2 config. Of course the most important commands of the lot as they add coins and launch games. Fired up the Adafruit utility and that works so the arcade controls are go and my test games SF3, Alpha and even tried DK Country on snes to make sure and its all good. So still plenty of configuring to do, getting buttons in the right spot but thanks so much guys, 2 player works. Brilliant work @rbaker @meleu @dankcushions and everyone else here really... you guys are definitely in my cool book. Damn it eats away at you when a problem gets the better of you... but oh so satisfying when the remedy is found.

meleu

Phew!
phew