(Solved) Pi5 : USB audio issue

DTEAM

Did you follow the steps in the document to choose a Mixer device ? Remove any .asoundrc configuration file you may have in $HOME, it shouldn't be needed.

Yes I did it. My two options seems to be Default and Master or HW and Headphone. Both doesn't work. I continue to dig it.

When I choose default and Master, I got no error message (mixer, etc.) but no sound in my headphone.

mitu

@DTEAM said in Pi5 : USB audio issue:

Yes I did it. My two options seems to be Default and Master or HW and Headphone. Both doesn't work. I continue to dig it.

The documentation page shows how to choose from one of the mixer device on the sound card, some of which may not be offered in EmulationStation options.

Do you get audio in emulators or using the ALSA speakter-test utility ?

DTEAM

@mitu

Not yet. What I got for now. I'll do a test

pi@retropie:~ $ pi@retropie:~ $ amixer scontrols -D default
Simple mixer control 'Master',0
Simple mixer control 'Capture',0
pi@retropie:~ $ amixer scontrols -D sysdefault
Simple mixer control 'Headphone',0
pi@retropie:~ $ amixer scontrols -D hw
Simple mixer control 'Headphone',0

pi@raspberrypi:~ $ amixer scontrols -D audio doesn't work. I must use preset value like default.
audio = my audiocard

DTEAM

@mitu said in Pi5 : USB audio issue:

Do you get audio in emulators or using the ALSA speakter-test utility ?

No sound for both

Does dtparam affect it?

# Enable audio (loads snd_bcm2835)
dtparam=audio=on

mitu

@DTEAM said in Pi5 : USB audio issue:

Does dtparam affect it?

No. In fact almost all of the video/audio related params you added have the effect as they did before.

No sound for both

Did you remove any ALSA configuration ? What's the out[put ofspeaker-test ?

DTEAM

@mitu said in Pi5 : USB audio issue:

Did you remove any ALSA configuration ? What's the out[put ofspeaker-test ?

yes

with card = default and device = master (seems to be the good combo.... but no sound )

https://pastebin.com/hf8Na64X

mitu

@DTEAM I don't see an error in speaker-test output. Make sure the output isn't muted by any chance.

DTEAM

@mitu

How can I see if it's muted or not ? The sound level is always at 100% in the EmulationStation UI or in the alsamixer UI

mitu

@DTEAM in alsamixer, the muted state is printed with an M underneath the volume slider. You can toggle the muted state by pressing m.

DTEAM

@mitu

Good news, It finally worked, It was on mute by default (I didn't use my keyboard in Alsamixer).

But now I have a new problem. I played with pulse audio in my "Audio UI" and now my Pi freeze all the time and I have no sound and no video. How can I reactivate Pulse Audio (now enable to create stream) . I already used "Reset to default" but nothing change. I lost options in my UI with my mess.

How can I reset my audio setup

mitu

@DTEAM said in Pi5 : USB audio issue:

I already used "Reset to default" but nothing change.

Reset to default I think only applies to the ALSA settings and just removes any RetroPie configuration file. In your case, it's not going to do anything, since RetroPie didn't configure your USB gamepad.

I lost options in my UI with my mess.

No idea, try to remove the packages you've installed and reboot.

DTEAM

@mitu
It works again. I re-install PipeWire and AudioPulse from rasPi config and everything works great. thanks for your support