Pi in a Dreamcast VMU Build - WIP
-
Today the postal carrier dropped off a small package from China. Inside were three little screens, with a minor difference on the back. These said "v2.1".
…and they WORK!
No garbage pixels. Plus, these came with plastic screen protector film on them. The first screens did not. Oh well, money wasted on those unless I can figure out another driver.
If you're an instagram kind of person, here's a short video of it working.
Next up I'll be trying to remove one of the new working screens from the board and wire that up.
-
I follow your build from some time now, and started to buy all pieces a few days ago. I hope the screens I bought are the new version !
-
@Arvester Unfortunately with these cheap boards there are tons of variants and it's almost impossible to know which one you're going to get. Good luck!
-
@obsidianspider Wonderful! I've got V1.1 LCD and also have the garbage pixels. Need to find a way to fix/conceal as I have 5pcs of them...
-
@satri360 since the 1.44" screen doesn't fill the entire opening I was going to make a bezel either out of black electrical tape or thin plastic so you don't see the white part. I figured if the v2.1 screens didn't fix the issue I would just make the bezel slightly larger to cover those rows. It's a bit hacky, but I figure it's not much different than how on older CRT televisions there was often a region of the picture tube that you didn't see due to the case, etc.
-
So, do you have a reference about what battery could fit ?
For now, I have the VMU and the Pi Zero, I'm waiting for the screens to arrive (probably next week). -
@Arvester said in Pi in a Dreamcast VMU Build - WIP:
So, do you have a reference about what battery could fit ?
I haven't gotten that far yet. I have an idea of what may fit, but I need to fit things into my test case and measure.
-
Have you seen that ?
https://www.adafruit.com/product/910
It would fit vertically, but needs power boost to achieve 5V. And then it would be 160x240px, much more than the 128x128 we found anywhere else.
-
@Arvester It would not be a perfect fit. The 1.44" screen barely fits as it is, and that screen also has a huge logic board that would take up a ton of room we don't have. It's also $40 for one screen. I paid $3 for one of the 1.44" screens.
-
@Arvester yeah it actually says 6-15VDC so that might need a spot more boosting, and the extra board for the composite decoder chip too might eat up some space.
you can actually run the cheepo 1.44" screens straight to the pi with just a resistor for the backlight if your soldering is up to it (excuse the cat hair in the photo!!)
anything to save a few mm :P
-
I have finally received my screens, unfortunately there's only one v1.1, the other one is something I never ordered (I ordered the two same) , there's a HUGE chip on the pcb and there is soldering points at the two ends, taking much more place. I can't use this. I didn't noticed at first glance, and I opened the wrong one first, 3$ lost ^^
Oh, and there's no problem with cat hair, I'm invaded too ^^
-
@Arvester that's a pain, nothing worse try waiting for weeks for bits and they arrive wrong 😞
Black rug and white cat was never a good idea 😛
-
USB charging port, and homemade home button.
Final mock-up (I broke the screen when I tried to take the pcb apart, I need to buy another one)
Pi logo was meant to go there !
Everything fits, room for battery is about 30x30x5mm.
Next step is solder everything, as I'm not sure about the pinout for the screen, I didn't start yet.
-
@Arvester Looks great! Which battery are you going with? I'm thinking about picking up this 500mAh one from Adafruit which is 36mm x 29mm x 4.75mm once they get more Pi Zero Ws in stock (I want to make the most of their high shipping minimum).
-
I'll probably take this one too, those I was looking for on eBay are too thick.
Also, I would not recommand to put the home button in the corner as I chose, it prevents the VMU to close properly. I had to modify it, the cap is now glued to the top part of the shell, and I cut some bits of the shell's lower part so I can slide it inside the cap. I think there is more room on the sides since the pi is in the middle.
And could you please give me the pinout you used to connect the screen to the pi ? I have 8 pins, labelled LED, SCK, SDA, AO, RESET, CS, GND and VCC. The @moosepr 's signature's guide uses different pinout, and I have to admit that I understand absolutely NOTHING in electronics (so I'm proud to have reach this far without help ^^'). Thanks !
-
For the fun:
-
@Arvester I haven't attempted to wire one up after removing it from the board yet, but this is what @moosepr gave me as far as how to wire it up on the board. Tracing things through to figure out which pin on the screen matches up to the pins on the PCB shouldn't be too big of a deal. That will be my next step. Once I get that working I'll be sure to post up what I came up with.
@moosepr said in Pi in a Dreamcast VMU Build - WIP:
@obsidianspider lets see if i can fill in the blanks for you
1 - 3.3v
2 - gnd
3 - gpio 8 (pin 24)
4 - gpio 25 (pin 22)
5 - gpio 24 (pin 18)
6 - gpio 10 (pin 19)
7 - gpio 11 (pin 23)
8 - 3.3v (can be the same as pin 1)my schematic is a little messy, lots of crossovers. tis something i need to refine
-
here you go, a more fleshed out version
VCC - 3.3v
GND - gnd
CS - gpio 8 (pin 24)
RESET - gpio 25 (pin 22)
AO - gpio 24 (pin 18)
SDA - gpio 10 (pin 19)
SCK - gpio 11 (pin 23)
LED - 3.3v (can be the same as pin 1) -
The big brown truck dropped off a little silver battery today. It looks like it's going to fit perfectly.
-
@obsidianspider awesome! Now get back to work!!
Contributions to the project are always appreciated, so if you would like to support us with a donation you can do so here.
Hosting provided by Mythic-Beasts. See the Hosting Information page for more information.