Power On/Off Button is in Reverse... Pushed-IN is OFF and Pushed-OUT is on.
-
@briandamico If it is working in reverse... Have you tried wiring it in reverse?
-
@AlexMurphy I've tried every which way and nothing has changed it
-
@briandamico Ok, I was being facetious, You need, if you want help, to give some basic info, you need to start from the very start. No one can guess your set-up. Please do not post a support request without first reading and following the advice in https://retropie.org.uk/forum/topic/3/read-this-first
-
@briandamico can you post a link to your switch you bought? So it is probably a dpdt )double pole double throw) or spdt (single pole double throw) switch. You have it wired to normally open (up positition). You need to put it on a different pin set for the normally closed (pushed down)
-
@briandamico best way to test is to use a multimeter on the diode setting. ->|- With the button pushed down, find two pins the make the multimeter beep or show something close to 0.00 (zero). Then push it back up. Then if those two pins dont beep pushed up they are the ones you want. The two pins on the opposite side of what you wired to are probably correct pins.
-
@AlexMurphy well my apologies Alex i was happy with my initial post as I thought it was pretty clear but i am happy to be extremely more in depth. so i will try to do so now
Pi Model - Raspberry Pi Model 3 B
Power Supply used: NorthPada Raspberry Pi 3 Model B Power Supply Charger AC Adapter 5V 3A PSU Micro USB 5 Feet with Power On / Off Switch
RetroPie Version Used - 4.2
Built From: Custom from scratch
USB Devices connected: 2 soldered USB female connectors
Controller used: Custom NES USB and Wii U Wireless
Mausberry Shutdown Circuit is being used and is properly set up via script to shut down properlythe problem: I have an NES mini (original) that i gut everything but the original Power On/off - reset - LED board.
I would like to use the original board and am pretty much am using it for the fact the power push button is in reverse. Out is ON and In is Off. plain and simplyI hooked up a sep LED to the Pie via the mausberry shut down LED tab and the ground to the Raspberry pis ground 3 GIO pin.
So if if this is too much to figure out, i am open to suggestions and part list suggestions to building a similar Bread board with a push button and reset button and led light if it will work properly. but if we can get the original to work in Non-reverse- id be forever grateful
hope this explains everything
-
@briandamico read my last two posts.
-
@edmaul69 if you go to http://mausberrycircuits.com and click SHUTDOWN CIRCUIT (USE YOUR OWN SWITCH) and see the direct micro USB one thats what i have.
now you ask about it being wired normally and i don't know what double pole double throw means and single old double throw means.
so how to i change the pin set if i am blunt asking that. I'm sure i already know but you can always tell me again
-
@edmaul69 ok i can try this with a multimeter
which you can see here.what setting would u like me to use
-
@briandamico you see you have two wires soldered to one side of the switch. Move them to the pins on the other side of your switch. That will probably fix it.
-
@edmaul69 well i did try that and it didn't not change.
i tried many many many many combos with the wires ed.
i did bottom 2 pins left side, bottom 2 pins right side
top right bottom right
top left bottom lefti really did but I'm happy to do the multi meter
-
@briandamico you need to put your multimeter on the 2k. That is where it shows the diode symbol ->|-. It should beep if you touch your test leads together or show 0.00 ish
-
@edmaul69 ok should i desolder the wires i have on the back? or leave them.
and you say when i touch two pins and the button is pushed IN, then i have my ON function and when i push out i should not get a signal?
and should i have the power on for real doing this?
-
@briandamico with it set on 2k on your multimeter it should beep or show 0.00 ish when you touch your test leads together. Same if you have the switch pushed down and you find the correct pins. Then when you put the switch in the off position those two pins shouldnt beep when you touch them.
-
@edmaul69 stupid to ask, but should i have the actual unit on or it doesn't need to be on for this
don't use multi meter much
-
@briandamico keep the pi unplugged.
-
@edmaul69 ok so I'm at it and on the 2k setting and I went through every pin and not one beep
Now I started lest day with the bottom left pin and then touched the black tip to it, then took red tip and moved my way up and around all 5 other pins and I did that clockwise to every pin and no beep
-
@edmaul69 to be honest I don't think there is any sound on this setting even when the tips touch
The beep sounds comes when I'm on the red volume logo looking one 2 over to the left from the 2k
-
@briandamico ok well try on that setting then. Most multimeters have it on the diode setting.
-
@edmaul69 I found two sets of pins top 2 left and 2 right ther had jumps in spike on the meter that went away when I flipped the switch but no sounds
I'm gonnna try these
Contributions to the project are always appreciated, so if you would like to support us with a donation you can do so here.
Hosting provided by Mythic-Beasts. See the Hosting Information page for more information.