SNES mini theme
@scott1986 what resolution is your screen?
lostless last edited by
@scott1986 I know this theme is designed to work with 1080P only. The assets are not really designed to be scaled down to lower resolutions. Especially a super lower res screen. I use GBZ35 theme on my gameboy build and it works really well for low res screens.
@lostless actually the snes mini theme is compatible with multiple different resolutions. In the customisation guide it lists them. It can then be changed in the config.xml.
scott1986 last edited by
@quicksilver the resolution of the screen is: 320x240
@lostless I use GBZ35 theme too but believe me the snes mini theme by @ruckage is my fav.
@quicksilver I change the resolution in config.xml but nothing.
@scott1986 I checked, it looks like 640x480 is the lowest supported resolution.
sergioad last edited by
Now that the grid view is in the final ES branch would be possible to add theming for it in this theme?
scott1986 last edited by scott1986
ash786i last edited by
hii, love these, total 'noob' so if anyone can tell me how to add these to ny retropi im be very grateful plsss :)
@ash786i The same way you'd add any theme - go into the RetroPie system in Emulationstation, then open the ES Themes menu and select the theme you want to install to add it to your installed themes.
Hello, I am having problems when loading the theme, do not load the interface graphics, it stays blank and you only see the names of the systems in plain text, the carbon theme loads correctly, if I have verified that inside of each category is the distribution of the cover and text applied, but nothing more, white backgrounds and no sounds.
I did not find anything about it, I hope you can help me. Thank you
@Paisano87 Can you add more info about your system - https://retropie.org.uk/forum/topic/3/read-this-first ?
Thank you for answering mitu
I have a Raspberry Pî 3 B and RetroPie 4.4.9 version
@Paisano87 What do you have your gpu/cpu memory split set to?
What do you have your gpu/cpu memory split set to?
Sorry, I do not understand what you are asking me
@Paisano87 Check the
/boot/config.txtfile on your sd card, or insert the SD card into your PC and open the
config.txtfile you find in there. Post the output of that file in the forum.
For more options and information see
Some settings may impact device functionality. See link above for details
uncomment if you get no picture on HDMI for a default "safe" mode
uncomment this if your display has a black border of unused pixels visible
and your display can output without overscan
uncomment the following to adjust overscan. Use positive numbers if console
goes off screen, and negative if there is too much border
uncomment to force a console size. By default it will be display's size minus
uncomment if hdmi display is not detected and composite is being output
uncomment to force a specific HDMI mode (this will force VGA)
uncomment to force a HDMI mode rather than DVI. This can make audio work in
DMT (computer monitor) modes
uncomment to increase signal to HDMI, if you have interference, blanking, or
uncomment for composite PAL
#uncomment to overclock the arm. 700 MHz is the default.
Uncomment some or all of these to enable the optional hardware interfaces
Uncomment this to enable the lirc-rpi module
Additional overlays and parameters are documented /boot/overlays/README
Enable audio (loads snd_bcm2835)
NOOBS Auto-generated Settings:
@Paisano87 You seem to have enough GPU memory, which is a good thing. Check your VRAM Limit setting in Emulationstation and make sure you have more than 80 Mb allocated (try with 120Mb also). Restart Emulationstation after you change the settings and see if you get better results.
@mitu Where should I go to modify the VRAM changes? forgive for my ignorance ... thanks
@Paisano87 In the Emulationstation menus, activated by pressing
Paisano87 last edited by Paisano87
@mitu Another way yo chance this?, in my emulationstation menu don't show this!, Only save metadata on exit and parse gameslist only