Retropie and Vice on Pi4 not working

[Trekinfo]

Hello,

i got serious Problems Running Vice on Retropie.
On my old Pi2 everything works fine. The new Install on a Pi4 did not work. Version 4.6.7

When i try to start Vice through the Emulation Station it didn't start and get me back into ES.
I tried D64 and Zip Games. The Logfile always says unsupportet Format.

BTW is Vice on Pi4 a other Version as on Pi2?
For a Pi2 the Package was 143 on Pi4 it is 155. Maybe that is the Issue?

Updating the whole System did also not work Vice is not loading.

Any Suggestions?

Greets Trekinfo

[brandflake11]

Have you tried lr-vice from the experimental packages option? I haven't tried vice myself, but maybe the libretro version will work.

[mitu]

BTW is Vice on Pi4 a other Version as on Pi2?
For a Pi2 the Package was 143 on Pi4 it is 155. Maybe that is the Issue?

Unlikely. Can you post the log file ? Are you using lr-vice or standalone vice ?

[Trekinfo]

Hi,

i tried vice standalone. lr-vice works but i would prefer Standalone Vice for better Configuation.

Here is the Log

Parameters: 
Executing: /opt/retropie/emulators/vice/bin/vice.sh x64 "/home/pi/RetroPie/roms/c64/BAGITMAN_00559_01.zip"
Archive:  /home/pi/RetroPie/roms/c64/BAGITMAN_00559_01.zip
  inflating: /tmp/retropie-archive/BAGITMAN.T64  
  inflating: /tmp/retropie-archive/VERSION.NFO  
terminate called without an active exception
/opt/retropie/emulators/vice/bin/vice.sh: Zeile 19:  1288 Abgebrochen             "$BIN" -chdir "$romdir" "${PARAMS[@]}" "$ROM"

This is a try with a zip Package of Bagitman.

Greets Trekinfo

[mitu]

I have no problems running the game with vice. Did you install vice from source or binary ? What version does Vice reports (F12, then go to Help -> About) ?

[Trekinfo]

Hi,

i tried binary and from source. No difference.
Vice is not starting, therefore no Version Report :(

Greets Trekinfo

[mitu]

I cannot reproduce this error - either with the game from the log file you posted or with another .d64 disc image. I have the latest binary (for the Pi4 system) also.

Can you try moving the configuration file out of the way (~/.vice/sdl-vicerc), just to check that's not some setting that's interfering ?

[BuZz]

Please post contents of your /boot/config.txt

[Trekinfo]

Hi toghether,

@mitu , moving the File out of way had no effect.

@BuZz here is the Config.txt

# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=on

[pi4]
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
dtoverlay=vc4-fkms-v3d
max_framebuffers=2

[all]
#dtoverlay=vc4-fkms-v3d
overscan_scale=1

Greets Trekinfo