USB Ports not working Retropie 4.7.1 / Raspberry Pi4B

therealtitleist

pi@retropie:~ $ dmesg | grep -i usb
[ 0.132160] usbcore: registered new interface driver usbfs
[ 0.132216] usbcore: registered new interface driver hub
[ 0.132348] usbcore: registered new device driver usb
[ 0.132687] usb_phy_generic phy: phy supply vcc not found, using dummy regulator
[ 21.444847] pci 0000:01:00.0: quirk_usb_early_handoff+0x0/0x7dc took 20018182 usecs
[ 21.585704] usbcore: registered new interface driver r8152
[ 21.585769] usbcore: registered new interface driver lan78xx
[ 21.585827] usbcore: registered new interface driver smsc95xx
[ 21.586301] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[ 22.086409] xhci_hcd 0000:01:00.0: USB bus 1 deregistered
[ 22.087762] usbcore: registered new interface driver uas
[ 22.087824] usbcore: registered new interface driver usb-storage
[ 22.098827] usbcore: registered new interface driver usbhid
[ 22.098839] usbhid: USB HID core driver
[ 25.591158] usbcore: registered new interface driver brcmfmac
pi@retropie:~ $

mitu

@therealtitleist said in USB Ports not working Retropie 4.7.1 / Raspberry Pi4B:

[ 21.586301] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[ 22.086409] xhci_hcd 0000:01:00.0: USB bus 1 deregistered

I see that the USB3 hub gets detected, but it's un-registered immediately. Post the full dmesg output on pastebin.com, maybe there's an indication in the full log. Do you get any under-voltage flash when booting ? Is this a new Pi ?

therealtitleist

@mitu

Thanks for all your help, here is the link for the full dmesg on Pastebin.

This is a completely new Pi, just got it in the mail last Saturday. It had another OS on it for about a day (PiStar) and the USB ports were working just fine in that config. Also no under-voltage indication at this point.

therealtitleist

@mitu

Also, I ran:

vcgencmd get_throttled

which returned

throttled=0x0

So should be okay from a power perspective.

mitu

@therealtitleist The USB hardware doesn't get initialized:

    0.946248] pci 0000:01:00.0: enabling device (0140 -> 0142)
[   21.444691] pci 0000:01:00.0: xHCI HW not ready after 5 sec (HC bug?) status = 0x811
[   21.444847] pci 0000:01:00.0: quirk_usb_early_handoff+0x0/0x7dc took 20018182 usecs
...
[   21.585827] usbcore: registered new interface driver smsc95xx
[   21.586268] xhci_hcd 0000:01:00.0: xHCI Host Controller
[   21.586301] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[   22.086380] xhci_hcd 0000:01:00.0: can't setup: -110
[   22.086409] xhci_hcd 0000:01:00.0: USB bus 1 deregistered
[   22.086477] xhci_hcd 0000:01:00.0: init 0000:01:00.0 fail, -110
[   22.086509] xhci_hcd: probe of 0000:01:00.0 failed with error -110

Try doing a full system update and see if that changes anything, other than that I'm tempted to believe it's a hardware issue. Is the PiStart image still working (with USB) ?

therealtitleist

@mitu I will toss PiStar back on it and double check.

What is the command for update / upgrade I can do from SSH?

therealtitleist

@mitu I found

sudo ~/RetroPie-Setup/retropie_setup.sh

and initiated an update from there - will that work?

mitu

@therealtitleist Yes, as long as you've chosen to update the OS & packages this should get your system up-to-date.

therealtitleist

@mitu

After the update to Retropie, still no change.

Also, after putting the Pistar image back on it, still deregisters the USB bus immediately.

Does that point to a hardware failure?

mitu

@therealtitleist said in USB Ports not working Retropie 4.7.1 / Raspberry Pi4B:

Does that point to a hardware failure?

Most likely yes.