raspberry pi 3 power supply

zipino82

@Folly hi listen I was thinking of doing this and what if instead of feeding it to the gpio the power to its connector? so I power in the right way with a 5000mah battery with the tc4056 module![batteria_raspi-transformed.jpg](Image dimensions are too big) ![batteria_raspi-transformed(1).png](Image dimensions are too big)

zipino82

@Lolonois hi listen I was thinking of doing this and what if instead of feeding it to the gpio the power to its connector? so I power in the right way with a 5000mah battery with the tc4056 module

Folly

@zipino82 said in raspberry pi 3 power supply:

@Folly hi listen I was thinking of doing this and what if instead of feeding it to the gpio the power to its connector? so I power in the right way with a 5000mah battery with the tc4056 module![batteria_raspi-transformed.jpg](Image dimensions are too big) ![batteria_raspi-transformed(1).png](Image dimensions are too big)

Makes no sense !
If there is somehow an overvoltage/undervoltage circuit then you will short that circuit with this method.

You have to choose one or the other.

Btw. I would not solder it to pin1 of the usb connector as it is too small.
You could even shortcut pins on the connector if you somehow don't solder it correctly.
If you manage somehow than the connection is very fragile.
I know that from experience.

The GPIO way is the best way.

zipino82

@Folly ok I trust you I'll move on to the gpio method Excuse my ignorance where would the overvoltage come from or vice versa?

Folly

@zipino82 said in raspberry pi 3 power supply:

Excuse my ignorance where would the overvoltage come from

From your power supply.
But if you have a good supply it should not exceed the voltage normally.

zipino82

@Folly I use a 3.7v 5000mAh battery with the TC4056

Folly

@zipino82

Can't help with your TC4056 don't know what your print exactly is doing.
But by the looks of it it's a li-Ion charger with buck-converter, a circuit with also the ability to convert the lower Li-Ion 3.7V-4,2V into 5V and supply your RPI.
Such things are always used with USB backup batteries.
I assume this is the same, otherwise you would not be able to use it with the RPI nor would that boy advise this circuit for the RPI
The 3.7 V doesn't mean anything to the RPI.
As long as your TC4056 outputs ~~5V +/- 20%~~ between 5V and 5.2V as supply voltage for the RPI your good to go.

You could check that first without connecting it to the RPI.
But you know with USB backup batteries they only start if something is connected to it.
But if your print has the 5V printed on it then I would assume it will output 5V I would skip the checking part and just try.

Lolonois

I have the slight feeling your project may derail without drawing the schematics first and studying datasheets/pi specs.

The TC/TP 4056 is a Li-ion charger, by default 1A loading current (which is good thus you don't have to change anything on it, as your battery is 5Ah).

On the Out+ / Out- of the TP4056 you get the battery voltage / loading voltage, but never 5 volts.

As Folly wrote, 3.7V won't start the Pi. You will need a so called boost-buck converter to step up the voltage to 5V.

Edit: cf. https://electronics.stackexchange.com/questions/284149/using-the-tp4056-to-charge-a-lipo-battery-and-supply-power-to-my-circuit

Folly

@zipino82

I think Lolonois has a point.

Make a blockdiagram.

Btw :
Found that 5V +/- 20% (would be between 4V and 6V) and is too high.
It should be between 5V and 5.2V

Lolonois

@Folly ouch, right: 6V is the maximum rating of the chip. 4.75 to 5.25 is the safe operating voltage (which is 5V +- 5%)