Multi Switch Shutdown Script!

darknior

WOAW excellent, i've receved my new NesPi+, i will try it :)
Thanks

dudumaroja

Hello.. i have a modification sugestion..

maybe you could integrate a save state function to the reset button.. using this!

https://github.com/GregorR/RetroArch/wiki/Network-Commands

this open doors to.. gracefully quit emulation ( retroarch compatible cores).. and other thinks like.. pressing reset for 5 seconds save state.. quick press load state..

you can even set the reset button to reset only the game you are playing.. and other thinks,

lostless

@dudumaroja You can do it your self. That's the whole fun of retro pie. If you are willing to do some research and get your hands dirty anything can be done.
heres a link to the recalbox help page with instructions on how to set this up.
https://github.com/recalbox/recalbox-os/wiki/RetroArch-Network-Commands-(EN)

OrehRuoy

Hello, is there a way to get the source code so that I can add led functionality to the code. I just want it to set a GPIO to high when turned on and to LOW when turned off.

Thanks.

mitu

@orehruoy The source is on github, link is in the 1st post - https://github.com/crcerror/ES-generic-shutdown.

cyperghost

@orehruoy You can modify the code of the script of course. But if you just want to glow a LED for power on/off control then use the UART port. A simple solution and no script needed.

Here is a guide of how to do this

OrehRuoy

@cyperghost said in Multi Switch Shutdown Script!:

@orehruoy You can modify the code of the script of course. But if you just want to glow a LED for power on/off control then use the UART port. A simple solution and no script needed.

Here is a guide of how to do this

I didn't know how to access your code in the pi. I will try that other method though seems simple. Thanks.

darknior

I finally try your script :)
Correct a problem for me because you install the script in /home/pi/Retropie/Scripts/ and this directory is on my USB drive.
I can't have good right to execute .sh on USB drive with the auto-mount :p
I change to use it in /home/pi/Scripts/ and it's perfect, thanks a lot :)

Only one question, when i want to quit RetroArch to ES i must clic 3 time on my reset button ... Is it normal ?
The power off button working fine every time. Using Reset in ES to restart ES is not working for me.
Your PID detection is impressive, it works with emulators and also OpenBOR :p

cyperghost

@darknior said in Multi Switch Shutdown Script!:

Only one question, when i want to quit RetroArch to ES i must clic 3 time on my reset button ... Is it normal ?
The power off button working fine every time. Using Reset in ES to restart ES is not working for me.
Your PID detection is impressive, it works with emulators and also OpenBOR :p

Well the detection of button press is just checked every 1 second. So you might press the button for a longer time.

The PID detection is introduced by runcommand script as entry point ;) And from this point I create PID array.

darknior

Ok thanks i understand better now :)

Your PID idea is cool and can maybe be used to improve other scripts?
I use this one, where we must make an array to list all the emulators and homebrews to stop music :(

https://retropie.org.uk/forum/topic/16458/modified-background-music-script-with-added-overlays

I'm sure we can do it with your idea, or maybe just detect when runcommand launch something and mute the music.

cyperghost

@darknior That's is possible, too.

try the parameter multi_switch.sh --es-emupid
If it returns 0 than there is no emulator called by runcommand.

mrfalk

Hi there love this script and community I’m trying to implement this to a 12v relay that turns the pi on and off using NO port so it’s ether open or close depending on if the 12v trigger is on or off

Is it possible with the generic trigger in the script?

cyperghost

@mrfalk Yes, this should work with generic button script.
So 12V closes the relais and as long your car keeps running the relais stays close. You turn off the vehicle the relais turns to off-state and releases the circuit.

mrfalk

Cool I was messing around with it yesterday but dident get it to work I’ll try again today after work.
And it’s not a car I’m using it’s a trigger signal from my projector that is normally used to tell screen go down when projector is on and hop when you turn the projector off.
But I guess it works the same.
And yes relay circuit is ether close or open depending in if the projector is on or off so same principle i guess

One question do I only install script and tell which button to use or do I need to mess with python commands?

cyperghost

@mrfalk

One question do I only install script and tell which button to use or do I need to mess with python commands?

You download the script with wget command or insert the code with nano and make the script executable (chmod +x). By default GPIO3 (=Pin5) is used because this pin is the only one to wake the Raspberry from deep sleep. The shutdown function is independent from GPIOs but as I said only GPIO3 offers full shutdown/repower ability.
The just type ./multi_switch.sh --generic and follow intructions. It's very likely you need to install raspi-gpio with sudo apt install raspi-gpio before but the script will tell you.

Yes please report your progress. But why you want to use a relais? Opto-isolators are much cheaper and easier to use.
Wiki Opto Isolator
https://en.wikipedia.org/wiki/Opto-isolator

mrfalk

couse im a newbie at the electronic/rasberry/ stuff but learning and relay was only thing i could think of and that i had laying around =)

when i do ./multi_switch.sh --generic nothing happens
im in /RetroPie/scripts & folder and when i type ./multi_switch.sh --generic nothing comes up or happens

i do get it to wake up from sleep when i turn projector on and relay goes to close state.
but i doesent shut down when i turn projector off and relay goes to open state

and uhm what do i need to make it executable sorry for my noobishness =/

Edit
nvm found out how to do it

Edit 2
but still cant get shutdown to work when the relay opens the circuit and the two pins get seperated (open/not shorted) nothing happens

and when i do raspi-gpio set PIN# ip pu i get unknown GPIO PIN# im guessing PIN# is 3 then

mrfalk

Finally got it to work after few hours of bug searching
and reason was that I hade (boot to desktop auto login as pi) and change to (boot to text console auto login as pi) and Now everything workes perfectly exectly as I want it to at least hehe thx @cyperghost for all your hard work on this script was exactly what I was looking for and I would have never could have done something like this myself

//peace

cyperghost

@mrfalk

boot to text console auto login as pi

I think it is enough to just write ./multi_switch --generic & to send the process to background. Then you avoid the second text console ;)

mrfalk

It works great it boots in to EmulationStation and turns On/Off

But I encounter a problem it randomly starts it self when projector is still off and dont give out signal to relay wich means circut is open

cyperghost

@mrfalk Then there is a kind of "backstroke" somewhere. Maybe it's the relay coil itself, or the relais falls back in closed state somewhere.... Really have no idea why this is happening.