Yet Another Pi Zero Portable!!

moosepr

DAMIT!

Hello

The 2.8 LCD selected by you is not supported in fbtft.
If you want us to do PCB similar to your selection than we can offer you 2 options
100usd development charges
Or
Moq. 25 quantity
One more economical option is we can supply raspberry pi LCD without 40 pin header and than you do the wiring on the gpio header pads
Regards
Tinylcd

moosepr

Right!! i have a plan. I have been doing some digging and the ili9341 screens are actually all the same!! there are 2 variations, the larger have touch, and the smaller dont, the first 14 pins are the same regardless of the presence of touch. So all i need to do, is buy a naked 2.8" screen, and unsolder the 2.2" screen i currently have, and transplant the 2.8" screen on top!! that way the pcb is actually the same size, if not smaller than the screen, and there is more space to play with!!

now to wait for the good ship chinapost :D

Parzival

@moosepr this is so cool. where do you get the controllers/buttons from. I would like to build my own.

moosepr

@Parzival i did some hunting, didint want the usual 'clicky' tactile switches that are commonly used. I found a guy on ebay that sells all kinds of switches for the repair of keyfobs and the like

http://www.ebay.co.uk/itm/321411385630

the ones i got are the OMTEN D3. They are really nice, will be great behind some actual buttons, will give that retro feel of the rubber domes

thedudester80

That is a cool portable. I like the battery body idea. Must be really thin and light. Good work .

moosepr

Yeah it's just a shade thicker than a sharpie, and only 105 grams, so it's pretty skinny

senkun

@moosepr said in Yet Another Pi Zero Portable!!:

Right!! i have a plan. I have been doing some digging and the ili9341 screens are actually all the same!! there are 2 variations, the larger have touch, and the smaller dont, the first 14 pins are the same regardless of the presence of touch. So all i need to do, is buy a naked 2.8" screen, and unsolder the 2.2" screen i currently have, and transplant the 2.8" screen on top!! that way the pcb is actually the same size, if not smaller than the screen, and there is more space to play with!!

now to wait for the good ship chinapost :D

hey. Just wondering how's it going with your project? Did you get the the transplant done? And, what are you using for audio? Just noticed that you have no audio out in your build.

moosepr

@senkun

Hey man

Well I technically have all the bits, just need to iron out a few bits.

My plan with transplanting a 2.8 screen onto a 2.2 board didn't work. The distance from solder connector to screen edge is the same for all screens, so it gave me no benefit. I'm just trying to knock up a little PCB that will allow me to connect the screen with minimal board.

As for the sound, I'm planning on using an adafruit digital audio board https://www.adafruit.com/products/3006 which will give me mono sound for the speaker, or maybe even switchable to the headphones. That would then leave me with a hole where the volume knob should be.

The problem I have now, is once I have got my PCB designed it's going to be another 2 weeks at least. Although I will end up with some spares I could distribute.

thedudester80

@moosepr That I2S amp works great with the pi zero. I used it for my altoid project. Really simple to setup as well.

Tekkaman_Slade

@moosepr - I wish that I2S audio amp was available when I built the NeoPiGamer. I'm definitely going to use it in my next pi zero build. Great find!!! Looking forward to your completed build.

moosepr

yeah that little amp is ideal. Shame its only mono. You can get stereo versions but they are a little larger (although looking at this, it doesnt have much 'amp' in there) https://shop.pimoroni.com/collections/pi-zero/products/phat-dac

The only issue i have, is the I2S board needs pin 18, which is currently what my ili9341 screen uses for its backlight

senkun

@moosepr said in Yet Another Pi Zero Portable!!:

The distance from solder connector to screen edge is the same for all screens, so it gave me no benefit.

alt text

http://www.aliexpress.com/item/2-8-inch-TFT-LCD-screen-display-ILI9341-40-pin-plug-in-type-support-8-16/32627803416.html

How bout this one?

moosepr

@senkun

That would technically work, the board I currently have is only 14 pin. It's the pure SPI interface, where as the 40 pin ones have raw pixel pins bundled.

I'm currently trying to design a board that has a 14 pin ribbon connector on one edge, and 8 pins of SPI on the other. Literally a bare minimum.

You could technically solder wires direct from the screen ribbon to the pi with nothing in the middle, but the 0 8mm pitch ffc connector doesn't lend itself to hand soldering

senkun

@moosepr

I must've been blind not only did not read where it said 40-pin, didn't even see how fine the pitch is. Took one look at the length of the ribbon and thought hey we could drop this on the 2.2" controller board...

btw, are you using the pitft22 dt overlay to enable your screen? Can I have your tft to zer0 pinouts for reference?

moosepr

@senkun

its easy done. there are so many screens and variations of them, its a minefield!!

I used the information from here
http://marcosgildavid.blogspot.co.uk/2014/02/getting-ili9341-spi-screen-working-on.html

then used a little reference image to trace things

https://www.element14.com/community/servlet/JiveServlet/previewBody/73950-102-10-339300/pi3_gpio.png

I was managing to get the thing working with the command

sudo modprobe fbtft_device pitft22 (i think, im working from memory here)

then i could mirror the terminal by typing

con2fbmap 1 1

but i was struggling to get things to activate at boot. Doing a bit of googling, i managed to find a video on youtube that had the solution to my problem. The problem is now, i am unable to find the video :( I will have to ssh onto my zero and use the command history and see how i fixed it

moosepr

so now i may also be able to add PCB design to my skillset

https://oshpark.com/shared_projects/BP9tGKag

in theory you can solder a 2.2" ili9341 screen direct to that board, then add wires from there to the pi

the 2.4" and 2.8" screens have an extra 4 pins on the connector, but thats just for the touch, so they could just be snipped off the ribbon (hopefully)

The resister on there is just for the backlight, you can change it to alter the backlight brightness, and it means there is one less pin needed from the pi (so i can use pin#18 for audio)

its the first PCB i have designed, so it may not be perfect, and it is untested, so it could burst int flames, who knows!!

senkun

@moosepr said in Yet Another Pi Zero Portable!!:

sudo modprobe fbtft_device pitft22

Ah thanks. That's already in the latest kernels, so it can be enabled by adding to config.txt;
dtparam=spi=on
dtoverlay=pitft22

in theory you can solder a 2.2" ili9341 screen direct to that board, then add wires from there to the pi

Haha. Nice little board. But wait! We can ditch the original red pcb and just solder screen ribbon wired direct to the zer0's gpios?

Here is the 2.2" tft without touch screen, just the 9 pins but there's that cap and resistor plus u1, q1, j1 which is not needed?

edit: seems like u1 is a 65z5 +voltage regulator chip which doesn't seem to be present on the 14 pin touch versions.

alt text

moosepr

@senkun yeah my board might be a little too minimal, but it's only costing me $2.20 for 3, so it's worth a punt. The only down side is the wait.

If it does work, I'm planning on making a custom board that will will link it all together into one. 2.2 screen on the front, some buttons on the button in a DMG-01 layout.

senkun

@moosepr said in Yet Another Pi Zero Portable!!:

@senkun yeah my board might be a little too minimal, but it's only costing me $2.20 for 3, so it's worth a punt. The only down side is the wait.

If it does work, I'm planning on making a custom board that will will link it all together into one. 2.2 screen on the front, some buttons on the button in a DMG-01 layout.

Apparently these screens will not work unless they're getting a strict 3.3V hence that 65Z5 regulator on board.

I'd say you need to regulate power to it somehow. Take it from the Zer0's 3.3V? You've ordered the boards so it'd be interesting to see if and how well it tolerates fluctuating power directly off a Lipo (from 4.2V max ~ 3V safe cutoff).

While the Zer0 can and has been tested to boot from as low as 2.8V (very unsafe if Lipo) and run unless there are 5v usb peripherals. But you have that charger/protector module (I think that cuts at 3.2V) and you've tested it running from just the Lipo with memory sticks and wi-fi dongle. So everything should still work if the screen is tolerant.

moosepr

@senkun
I am running my screen from the 3.3v line on my zero anyway, so I'm assuming everything will be OK without regulation.

Your brave ordering my boards! I couldn't find a proper connector in fritzing so i had to hand build one from the normal pads. There are some things quite close together, so it will need to be tested for shorts.