XBOXDRV Guidance Needed

mediamogul

Your controller's ID can be discovered with ls /dev/input/by-id/. However, if it doesn't have an ID, you can also call out to the USB path where you know the controller is. For example, by adding:

--evdev /dev/input/by-path/platform-3f980000.usb-usb-0:1.2:1.0-event-joystick

you're telling xboxdrv to map the controller in the upper, left USB port on a Pi 3. To discover the other path listings, plug a controller into whichever port you're looking to use and type ls /dev/input/by-path/.

hansolo77

I am figuratively pulling my hair out. Because I wasn't getting anywhere, I decided to start completely over. I deleted all the controller config files that RetroArch uses. I then disconnected the USB hub that the Mayflash Sega/Atari adapter and Raphnet NES adapter were connected to. I then replaced the retroarch.cfg file with the default. I then went into the RetroPie-Setup scripts and triggered the ES function to reset ALL controllers (removing them and prompting for a re-configure). That should put me back to bare minimum with no configured controllers right? Well...

With everything still disconnected, except for the Xbox controller, I turned the machine off then back on. ES prompted for input. I configured ONLY the Xbox controller. I then tried to load up a game. The game loads, but none of the controls do. WTF. OMG I can't believe it. Not even the USB keyboard I have is being recognized by RetroArch.

This is crazy. I'm restoring my backup SD card and just living with it the way it was. I can't figure out what's going on, and it's really upsetting me. With NOTHING connected, bare essentials, it should work with whatever is picks up is connected. It used to work fine until I updated RetroArch. Now I got nothing but trouble.

mediamogul

@hansolo77

I can definitely relate. It's situations like your having where you almost start believing in poltergeists or gremlins. I hope it works out. Just tag me in if you decide to give it another go down the road.

hansolo77

@mediamogul

Oh you bet I will. :) Honestly, I think I just need to sleep this off and come back some other day. I don't want to ruin my vacation being pissed off at this thing. It's supposed to be enjoyable. lol

hansolo77

@mediamogul
Back at it again. I started with your doc you wrote on how to set this all up. You indicated a possible workaround using a SYMLINK in the dev rules so you can get proper remaps with Bluetooth controllers. This got me thinking. Since part of the problem I seem to be having is due to the devices being enumerated differently on bootups, could I use this method here? The only obstacle is that the ATTRS{name} and ID_MODEL is the same for both event's. There is only 1 USB plug, but it has 2 controller connectors on it. Is there a way to create the SYMLINK dev rule another way? Without it requiring those two indicators? Maybe an alternative?

Here is what I'm looking at (evtest):

Available devices:
/dev/input/event1:      Microsoft Microsoft® 2.4GHz Transceiver v8.0
/dev/input/event2:      Microsoft Microsoft® 2.4GHz Transceiver v8.0
/dev/input/event3:      Microsoft Microsoft® 2.4GHz Transceiver v8.0
/dev/input/event4:      raphnet.net nes2usb
/dev/input/event5:      raphnet.net nes2usb
/dev/input/event6:      Mayflash Ltd Mayflash MD USB Adapter
/dev/input/event7:      Mayflash Ltd Mayflash MD USB Adapter

Essentially (for this part), the event4 and event5 devices change to 3/4 respectively on the occasion. This typically happens based on whether or not the Xbox Controller is turned on (not listed now because it's off).

EDIT - Guess I was wrong there too. I turned ON the Xbox Controller, and re-ran the evtest. It sets the controller up on event0 and the NES events didn't change. I don't get it. :(

EDIT 2 - Tried again. Turned the system off, Xbox Controller off, boot up, evtest shows the NES controllers now on event3 and event4. Then I turn on the Xbox controller, and evtest shows it on event7 now. So I definitely need to establish some kind of rule that would allow me to map the controller based on it's "name" (symlink) rather than by it's event id.

EDIT 3 - Did another test. This time evtest comes up with the Xbox controller on event5. So maybe it's the Xbox controller that's being unreliable, and depending on where the Pi installs it to determines the placement of all the other controller events. In either case, I still need to do something to assign the devices to specific events or something.

mediamogul

@hansolo77 said in XBOXDRV Guidance Needed:

In either case, I still need to do something to assign the devices to specific events or something.

The symlinking you mentioned would probably do the job, but the whole udev process to achieve it might be overkill in your case. As long as your controller is always plugged into the same port, assigning the mappings via /dev/input/by-path/ is always a very reliable option. I actually have to use this method, as I use four identical controllers and they all naturally share the same ID information.

hansolo77

Any chance I could get you to elaborate? :) I could probably figure it out on my own, but you 'd probably know how to do it faster.

mediamogul

@hansolo77

Sure. Just plug your controller into whichever port you plan on keeping it in, then run ls /dev/input/by-path/. As an example, a controller plugged into the upper, left usb port on a Pi 3 will likely read as being; platform-3f980000.usb-usb-0:1.2:1.0-event-joystick. After you have that, you'd just add it to your xboxdrv config as:

--evdev /dev/input/by-path/platform-3f980000.usb-usb-0:1.2:1.0-event-joystick

hansolo77

@mediamogul Thanks, I'll take a look at it soon as I finish dinner!

hansolo77

@mediamogul said in XBOXDRV Guidance Needed:

ls /dev/input/by-path/

So these "paths" will never change as long as I keep the adapters connected on the same ports?

EDIT This still won't work for me. I did an evtest of each event-joystick and it only gives me the player 1 port of the adapter.

mediamogul

@hansolo77

Did two listings show up with ls /dev/input/by-path/?

hansolo77

@mediamogul When I do ls /dev/input/by-path, I get this:

platform-3f980000.usb-usb-0:1.2:1.0-event-joystick      platform-3f980000.usb-usb-0:1.4.1.2:1.0-event-joystick  platform-3f980000.usb-usb-0:1.4.3:1.0-event-kbd
platform-3f980000.usb-usb-0:1.2:1.0-joystick            platform-3f980000.usb-usb-0:1.4.1.2:1.0-joystick        platform-3f980000.usb-usb-0:1.4.3:1.1-event-mouse
platform-3f980000.usb-usb-0:1.4.1.1:1.0-event-joystick  platform-3f980000.usb-usb-0:1.4.1.2:1.1-event-joystick  platform-3f980000.usb-usb-0:1.4.3:1.1-mouse
platform-3f980000.usb-usb-0:1.4.1.1:1.0-joystick        platform-3f980000.usb-usb-0:1.4.1.2:1.1-joystick        platform-3f980000.usb-usb-0:1.4.3:1.2-event-kbd

I tested each event-joystick, and I came up with this:

Xbox
platform-3f980000.usb-usb-0:1.2:1.0-event-joystick

Raphnet
platform-3f980000.usb-usb-0:1.4.1.1:1.0-event-joystick

MayFlash
platform-3f980000.usb-usb-0:1.4.1.2:1.0-event-joystick

MayFlash
platform-3f980000.usb-usb-0:1.4.1.2:1.1-event-joystick

So while it would work with the MayFlash (Atari/Sega) it only saw one entry for the the Raphnet (NES). When I do an generic evtest I get this:

No device specified, trying to scan all of /dev/input/event*
Not running as root, no devices may be available.
Available devices:
/dev/input/event0:      Xbox 360 Wireless Receiver
/dev/input/event1:      Microsoft Microsoft® 2.4GHz Transceiver v8.0
/dev/input/event2:      Microsoft Microsoft® 2.4GHz Transceiver v8.0
/dev/input/event3:      Microsoft Microsoft® 2.4GHz Transceiver v8.0
/dev/input/event4:      raphnet.net nes2usb
/dev/input/event5:      raphnet.net nes2usb
/dev/input/event6:      Mayflash Ltd Mayflash MD USB Adapter
/dev/input/event7:      Mayflash Ltd Mayflash MD USB Adapter

So it looks like it sees multiple events but for a single device (which makes sense). But it doesn't do it that way with the MayFlash.

EDIT - If I run evtest /dev/input/by-path/, I get this:

evtest: can't get version: Inappropriate ioctl for device

EDIT 2 - If I run ls /dev/input/by-id, I get this:

usb-Mayflash_Ltd_Mayflash_MD_USB_Adapter-event-joystick            usb-Microsoft_Microsoft®_2.4GHz_Transceiver_v8.0-if01-mouse
usb-Mayflash_Ltd_Mayflash_MD_USB_Adapter-if01-event-joystick       usb-Microsoft_Microsoft®_2.4GHz_Transceiver_v8.0-if02-event-kbd
usb-Mayflash_Ltd_Mayflash_MD_USB_Adapter-if01-joystick             usb-©Microsoft_Xbox_360_Wireless_Receiver_for_Windows_E1594E70-event-joystick
usb-Mayflash_Ltd_Mayflash_MD_USB_Adapter-joystick                  usb-©Microsoft_Xbox_360_Wireless_Receiver_for_Windows_E1594E70-joystick
usb-Microsoft_Microsoft®_2.4GHz_Transceiver_v8.0-event-kbd         usb-raphnet.net_nes2usb_1228-event-joystick
usb-Microsoft_Microsoft®_2.4GHz_Transceiver_v8.0-if01-event-mouse  usb-raphnet.net_nes2usb_1228-joystick

Looks like it's only seeing 1 raphnet there too. :(

hansolo77

@hansolo77 @mediamogul
I think I need to do this:
http://www.raphnet-tech.com/support/retropie/

mediamogul

@hansolo77

The adapters that have multiple ports are notoriously difficult to map outside of Windows and they're all pretty much set up the same way. An example that I've worked with personally is the Mayflash Gamecube to WiiU adapter. In it's USB mode, all the ports register as being one device also. The only way I could get it working with my RetroPie setup was to use Toadking's driver in WiiU mode. It's been a while, but as I recall, there's a certain aspect of the USB HID spec that is responsible for delineating the multiple ports and it's unique to Windows for some reason.

Edit:

I think I need to do this:
http://www.raphnet-tech.com/support/retropie/

Looks like your right as per:

"The way multi-player adapters and boards are implemented make them appear as one single controllers in Linux. For instance, the adapters based on the 4nes4snes board (eg: Four SNES to USB) used to register as a joystick with 4 pairs of axes, and 32 buttons (8 per controller). But at some point, this became 2 axis (a mix of all controllers) but still 32 buttons.

To fix this problem, I wrote a kernel patch to make the adapters appear as a set of independant controllers in march 2015 and it was included in the Linux kernel starting at version 4.2.0. With this patch, things are cleaner than ever. But as 2016-05-02, the kernel included in the RetroPie SD images is still one of the 4.1 series... So besides waiting, what can one do? Of course geting the kernel sources, applying the patch, compiling and installing it! But there is an easier way."

This will likely do the job and it's great to see that this addition is waiting around the corner in a future kernal update. Seeing as how several adapters use this same method, hopefully this will solve the issue all around.

hansolo77

Yeah I tried to run his script to update the cmdline.txt but it didn't work after rebooting. I think it's because I've updated the kernel in the past without including his patches. So I'm going through that now. Gonna take a good couple of hours. I sent his support email a message though to see if he suspects the problem I'm having is related, and see if he has any tips or suggestions.

mediamogul

@hansolo77

Let me know what he says. This is an interesting development and I might make use of it myself sometime in the future.

hansolo77

Sure thing. It's interesting the things we discover along the way trying to solve a problem. This all started because I wanted to get the latest version of RetroArch to have Leaderboard support. That led to the config files getting broke and needing to get replaced with the generic default. That led to all the custom changes I did for my controllers to work on the fly to disappear and stop working. Now I'm back to rebuilding the kernel so I can have a more permanent XBOXDRV solution. I still can't figure out why nobody else is having all these problems lol.

mediamogul

@hansolo77

Ha! Let's face it, solving these issues is the real game, saving the princess is just a bonus round.

hansolo77

@mediamogul You sure got that right! But this is fun too. This is what keeps me spending money where I shouldn't. :)

hansolo77

Well after fully rebuilding the kernel with the correct patches, I'm still having the same symptoms. My Raphnet NES2USB adaptor is being identified with 2 event ID's, but only one device ID.

This ONE hindrance is causing me ALL my issues. :( If I can distinguish a specific device for Controller 1 and Controller 2, I'm SOL. Does anybody have any idea on a different approach here?