save configuration on exit issue

Floob

@smoothmalik Its just the output of the command above I'm after really.
Which fba are you running?

smoothmalik

pi@retropie:~ $ ls -lah /opt/retropie/configs/psx
total 16K
drwxr-xr-x 2 pi pi 4.0K May 27 16:14 .
drwxr-xr-x 52 pi pi 4.0K May 27 16:16 ..
-rw-r--r-- 1 pi pi 206 May 27 16:14 emulators.cfg
-rw-r--r-- 1 pi pi 221 May 27 16:14 retroarch.cfg

im running whatever version of FBA is on the 3.8 build. Im not running FBA Next or pifba

Floob

@smoothmalik fba-next is the default in 3.8 though?
Can you run ls -lah /opt/retropie/configs/fba ?

smoothmalik

im running just regular FBA

here you go
pi@retropie:~ $ ls -lah /opt/retropie/configs/fba
total 176K
drwxr-xr-x 2 pi pi 4.0K Jun 15 23:11 .
drwxr-xr-x 52 pi pi 4.0K May 27 16:16 ..
-rw-r--r-- 1 pi pi 195 May 27 16:13 capex.cfg
-rw-r--r-- 1 pi pi 0 Jun 12 18:18 content_history.lpl
-rw-r--r-- 1 pi pi 414 Jun 7 01:49 emulators.cfg
-rw-r--r-- 1 pi pi 1.1K May 27 16:13 fba2x.cfg
-rw-r--r-- 1 pi pi 49K Jun 15 23:12 fb_alpha_libretro-1.cfg
-rw-r--r-- 1 pi pi 49K Jun 14 03:42 fb_alpha_libretro.cfg
-rw-r--r-- 1 pi pi 46K Jun 16 00:33 retroarch.cfg
-rw-r--r-- 1 pi pi 221 May 27 16:14 retroarch.cfg.rp-dist

Floob

@smoothmalik
Whats the "default=" value show when you run nano /opt/retropie/configs/fba/emulators.cfg

These 2 files are produced when you save in RGUI

-rw-r--r-- 1 pi pi 49K Jun 15 23:12 fb_alpha_libretro-1.cfg
-rw-r--r-- 1 pi pi 49K Jun 14 03:42 fb_alpha_libretro.cfg

And by the looks of the file size of retroarch.cfg you have either renamed one of those files to be retroarch.cfg or you have added a lot of lines in there.

The video above explains why RGUI produces the large 46k files and why RetroArch wont read them. It also shows how to rip the relevant line(s) out to add to the original (very small) retroarch.cfg file.

smoothmalik

default="lr-fba"

I havent renamed anything. I got desperate yesterday and today and tried to save the config file in rgui after I made some changes but of course they didnt stay. The only change ive made in retroarch.cfg was done in the config editor and that was enabling bilinear filtering (true) and save on exit (true).

Floob

@smoothmalik I'm assuming you have upgraded an older version of RetroPie.
I would reset your RetroArch config with

rm /opt/retropie/configs/fba/retroarch.cfg
cp /opt/retropie/configs/fba/retroarch.cfg.rp-dist /opt/retropie/configs/fba/retroarch.cfg

Then go back in the config editor, just enable bilinear filtering, then pastebin your /opt/retropie/configs/fba/retroarch.cfg

smoothmalik

i didnt get far

pi@retropie:~ $ rm /opt/retropie/configs/fba/retroarch.cfg
rm: cannot remove ‘/opt/retropie/configs/fba/retroarch.cfg’: No such file or directory

I also tried removing though ftp also wouldnt let me

Floob

Thats odd?

This should show its there
ls /opt/retropie/configs/fba/r*

This should remove the old one
rm /opt/retropie/configs/fba/retroarch.cfg

unless you ran it twice, so its not there now?

smoothmalik

here the paste bin. Bilinear filtering reamained enabled and so did save on exit. The retroarch.cfg file is 46.1 kb now

http://pastebin.com/uYnT3SXy

I got the left joystick working in config editor.

Floob

If its now working for you, then great. But your retroarch.cfg really shouldnt be looking like that.

smoothmalik

I'll do a clean install maybe tomorrow. Thanks you've been extremely helpful.

Floob

No problem. If you do make a clean install, check out the video to explain how to make RGUI changes stick.