Xbox360 wireless controllers - receiver connectivity issues

raelik · 6 Jul 2016, 18:37

@pomme Yeah, I should have mentioned you should run sudo su - (to switch to root) before doing any of this. Fixed my post (again).

rossoe · 8 Jun 2016, 20:55

worked perfectly thank you.

can we easily upgrade to the newly released 3.8.1 without the kernel jumping back up to the broken version?

trixter1981 · 9 Jun 2016, 07:12

done the upgrade to 3.8.1, it's okay. The kernel is untouched.

zanie420 · 12 Jun 2016, 16:42

RPI 3
Retropie 4.0-dev

Having the same issues getting wireless 360 receiver to work consistently after fresh install and enabling xboxdrv via the script. Tearing my hair out! No output from jstest /dev/input/js0.

However, I too can get it to work by logging into SSH as root and using:

killall xboxdrv
xboxdrv --trigger-as-button --id 0 --led 2 --deadzone 4000 --silent & sleep 1

This didn't work until I blacklisted xpad and installed xboxdrv via apt-get

Randomly the controller stops working and you have to redo it. Restarting puts you back a square one, but the workaround IS consistent it seems.....

What the hell am I doing wrong?

backstander · 12 Jun 2016, 17:34

@zanie420 if you read down below my post (trixter1981 & raelik posts), there is a workaround that will downgrade the kernel. The xboxdrv seams to work pretty consistently after this downgrade.

ataritoday · 14 Jun 2016, 02:14

Hi All,

Apologies, another Newb.....

I tried the script in above...sudo worked, curl worked and it downloaded something...

hard to tell if tr-d worked or not.....

same with chmod , did not seem to do much, but no error either....

when I get to the line /usr/ line I get a syntax error.... is this suppose to be a continuation of the line above ? what does it do ?

Apologies for the basic questions.

Thx
Jim

mazjohn · 14 Jun 2016, 17:31

Another Newb when it comes to installing scripts and Linux Kernels, ..cannot get past the first part without errors so far... Attempting this on clean install of V3.81 , over an hour struggling... will keep trying.

I would hope there would be an updated image release soon that officially addresses this??

Update: I gave up. had to start over with a clean install of retropie V 3.6 which uses an older Kernel. Works fine now.... Hopefully there is an update soon that addresses out of box issues with 3.81.

sberrieman · 14 Jun 2016, 20:46

Hi,

I'm getting a gzip error when running the final command and it performs the rollback - any ideas?

NizZ8 · 16 Jun 2016, 22:15

@raelik Thanks for posting, fixed the issue for me with a fresh install of 3.8.1

herb_fargus · 22 Jun 2016, 19:16

An issue has been logged here: https://github.com/raspberrypi/linux/issues/1540

PhantombrainM · 24 Jun 2016, 08:01

Thank you. This worked so far.
But one question for the future: how to roll back?
apg-get update and upgrade does not install the newest kernel anymore.
How do I switch back to an upgrading distribution when the problems have been fixed?
regards PhantombrainM

dabone · 25 Jun 2016, 19:29

I'm trying to get a fresh install using my dp9 gpio controllers along with my wireless xbox 360 controllers.
I guess I'm outta luck at the moment? I tried a fresh install, then backing down the kernel, but then I can't install the gamecon driver.

Later,
dabone

Jexoteric · 25 Jun 2016, 20:59

The script above works well, but it didn't fix the flashing ring of lights that would normally indicate the controller is still trying to connect. Shouldn't the light switch to the corresponding lighted quadrant that the receiver sees the controller as (1-4)?

Is the flashing ring the normal behavior or is something still incorrect?

backstander · 26 Jun 2016, 20:29

@Jexoteric

I'm not sure if you already did this step but...you'll still need to setup the Xbox 360 controller in the RetroPie Setup Script. This should setup the correct "corresponding lighted quadrant" to light up.

https://github.com/retropie/retropie-setup/wiki/Setting-up-the-XBox360-controller

Jexoteric · 29 Jun 2016, 02:13

@backstander nailed it. LED's work now, and are much less annoying.

Arcuza · 1 Jul 2016, 23:12

I'm having issues with this as well. It seems like random results, sometimes it works, sometimes it doesn't. Sometimes LEDs are flashing, sometimes they show contoller#, sometimes they die.

Is there a working fix? Will a fix be available in the next version?

I'm running 3.8.1 with raspberry PI 3.

billymalcolm · 7 Feb 2016, 01:16

Upon running script, I get

Gzip: stdin: not in gzip format
Tar: child returned status 1
Tar: error is not recoverable: exiting now

Anyone else get this? What have I done wrong?

archie778 · 13 Aug 2016, 21:11

@raelik I used this code to fix my controllers and it worked perfectly to fix the wireless controllers, however upon reboot, now i have no sound, and my resolution is way off... any idea what went wrong?

archie778 · 13 Aug 2016, 21:14

actually the controllers only work in the emulationstation menu, once i get into a game in an emulator they do nothing (i've tried re mapping them)

Maynard · 28 Aug 2016, 10:56

is this issue fixed with retropie 4.0? i've installed it and xbox360 controller works as it should. the only thing is the annoying flashing ring. i had this problem on other systems when using xpad, so that i allays used xboxdrv instead of xpad. is there a fix so that the lights don't rotating in circle anymore?

has anyone tested the downgrade script with retropie 4.0?