RetroPie forum home
    • Recent
    • Tags
    • Popular
    • Home
    • Docs
    • Register
    • Login
    Please do not post a support request without first reading and following the advice in https://retropie.org.uk/forum/topic/3/read-this-first

    8bitdo FC30pro not working in emulators

    Scheduled Pinned Locked Moved Help and Support
    27 Posts 9 Posters 26.2k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • J
      JiePieWie
      last edited by

      I was away for a few days so my comments are a bit later than expected :-) I will reload the 1.68FW again and go through the pairing/config etc routine again. How do i start with a 'clean' ES-config so i can go through the config procedure like it's newly installed? Just to be sure..

      FloobF 1 Reply Last reply Reply Quote 0
      • FloobF
        Floob @JiePieWie
        last edited by

        @JiePieWie
        If you edit your /home/pi/.emulationstation/es_input.cfgfile to read:

        <?xml version="1.0"?>
<inputList>
  <inputAction type="onfinish">
    <command>/opt/retropie/supplementary/emulationstation/scripts/inputconfiguration.sh</command>
  </inputAction>
</inputList>

        it should then prompt as normal to configure a controller.
        Or you could manually prompt this by pressing Start when in ES and choosing "Configure Input"

        Please read the Docs before asking a new question.
        RetroPie Help Guides: https://goo.gl/3gcNsT

        1 Reply Last reply Reply Quote 0
        • ProxyCellP
          ProxyCell
          last edited by

          I have the FC30 Pro here (the famicom looking one) and it is working wonderfully. It did not get the controls setup automatically though and I had to set them myself using jstest so please consider that.

          RPi3b+ - No overclock
          RetroPie - latest from Github, as always
          2x SF30 Pro 8Bitdo controllers

          J 1 Reply Last reply Reply Quote 0
          • J
            JiePieWie @ProxyCell
            last edited by

            @ProxyCell said in 8bitdo FC30pro not working in emulators:

            I have the FC30 Pro here (the famicom looking one) and it is working wonderfully. It did not get the controls setup automatically though and I had to set them myself using jstest so please consider that.

            jstest? My controller is not usable via jstest because it's not 'attached' under /dev/input/js.. I can see there only js0 and js1 which are my Xin-Mo arcade joysticks. And they work fine.. Should i be able to see my FC30pro there also?

            1 Reply Last reply Reply Quote 0
            • ProxyCellP
              ProxyCell
              last edited by

              Yes @JiePieWie
              Have you registered the controller in both the bluetooth menu and in ES?

              RPi3b+ - No overclock
              RetroPie - latest from Github, as always
              2x SF30 Pro 8Bitdo controllers

              1 Reply Last reply Reply Quote 0
              • BuZzB
                BuZz administrators
                last edited by

                with the latest version of the retropie-setup script and firmware 1.68 it should work fine. The latest version of the bluetooth script in retropie-setup has the facility to install the correct udev rule, and also to connect to the controller in the background at any time.

                To help us help you - please make sure you read the sticky topics before posting - https://retropie.org.uk/forum/topic/3/read-this-first

                1 Reply Last reply Reply Quote 0
                • P
                  pimpmaul69 @JiePieWie
                  last edited by Floob

                  @JiePieWie i would go back to 1.69 then add the file manually in /opt/retropie/configs/all/retroarch-joypads. there is a change in retropie that uses the fc30 pro and nes30 pro universally so i would make both these configs if i were you.

                  first file named: 8BitdoFC30Pro.cfg

                  this is how i have it configureded inside mine. i did disable stuff i dont use. feel free to change it to your liking. i did add functions to change discs for ps1. if you keep the disk changing info in this file es cant overwrite the file. if you configure the controller in es it wont do anything after you select ok after setting up the controller. wait a minute and then reboot. the controller will be configured in es and these files will remain intact. if you want es to be able to change it feel free to not keep that stuff. only problem is emulationstation is good at overwriting these files with a blank file.

                  input_device = "8Bitdo FC30 Pro"
input_driver = "udev"
input_start_btn = "11"
input_select_btn = "10"
input_up_btn = "h0up"
input_down_btn = "h0down"
input_left_btn = "h0left"
input_right_btn = "h0right"
input_a_btn = "0"
input_b_btn = "1"
input_x_btn = "3"
input_y_btn = "4"
input_l_btn = "6"
input_r_btn = "7"
input_l2_btn = "8"
input_r2_btn = "9"
input_l3_btn = "13"
input_r3_btn = "14"
input_l_y_minus_axis = "-1"
input_l_x_plus_axis = "+0"
input_l_y_plus_axis = "+1"
input_l_x_minus_axis = "-0"
input_r_x_plus_axis = "+2"
input_r_y_plus_axis = "+3"
input_r_x_minus_axis = "-2"
input_r_y_minus_axis = "-3"

input_save_state_btn = "nul"
input_load_state_btn = "nul"
input_state_slot_decrease_btn = "nul"
input_state_slot_increase_btn = "nul"

input_disk_eject_toggle_btn = "3"
input_disk_next_btn = "7"
input_disk_prev_btn = "6"
input_menu_toggle_btn = "1"
input_exit_emulator_btn = "11"
input_enable_hotkey_btn = "10"
input_reset_btn = "nul"

                  the second file is named: szmy-powerLtd.Joypad.cfg

                  input_device = "szmy-power Ltd.  Joypad  "
input_driver = "udev"
input_start_btn = "11"
input_select_btn = "10"
input_up_btn = "h0up"
input_down_btn = "h0down"
input_left_btn = "h0left"
input_right_btn = "h0right"
input_a_btn = "0"
input_b_btn = "1"
input_x_btn = "3"
input_y_btn = "4"
input_l_btn = "6"
input_r_btn = "7"
input_l2_btn = "8"
input_r2_btn = "9"
input_l3_btn = "13"
input_r3_btn = "14"
input_l_y_minus_axis = "-1"
input_l_x_plus_axis = "+0"
input_l_y_plus_axis = "+1"
input_l_x_minus_axis = "-0"
input_r_x_plus_axis = "+2"
input_r_y_plus_axis = "+3"
input_r_x_minus_axis = "-2"
input_r_y_minus_axis = "-3"

input_save_state_btn = "nul"
input_load_state_btn = "nul"
input_state_slot_decrease_btn = "nul"
input_state_slot_increase_btn = "nul"

input_disk_eject_toggle_btn = "3"
input_disk_next_btn = "7"
input_disk_prev_btn = "6"
input_menu_toggle_btn = "1"
input_exit_emulator_btn = "11"
input_enable_hotkey_btn = "10"
input_reset_btn = "nul"
                  1 Reply Last reply Reply Quote 0
                  • D
                    Duhjoker
                    last edited by Floob

                    Im having the same problems with my NES30 pro. I started with 1.68 and flashed the controller to 1.69. Works fine in ES and on LR-fceumm but that's it.
                    I looked at the config file at opt/Retropie/configs/all/retro arch-joy pads posted above. All the button mappings match the above but it's missing the firmware print at the top. Am I supposed to write the config file exactly as given above? It's all jumbled too in no particular order.

                    Why are my posts all in code squares ?

                    BuZzB 1 Reply Last reply Reply Quote 0
                    • D
                      Duhjoker
                      last edited by

                      I have literally done every thing that this thread has suggested and some things a few other threads have suggested. The controller works fine in ES and works for the Nintendo emulator but nothing else.

                      P 1 Reply Last reply Reply Quote 0
                      • P
                        pimpmaul69 @Duhjoker
                        last edited by pimpmaul69

                        @Duhjoker said in 8bitdo FC30pro not working in emulators:

                        I have literally done every thing that this thread has suggested and some things a few other threads have suggested. The controller works fine in ES and works for the Nintendo emulator but nothing else.

                        Are you using libretro emulators? When you pick a game you need to push the "0" button which is "button a" on the 8bitdo controlller to get into options. Then choose emulators that start with "lr-" example: "lr-snes9x-next"

                        1 Reply Last reply Reply Quote 0
                        • D
                          Duhjoker
                          last edited by

                          Ok the only "lr" emulator I'm using is the lr-fceumm which works fine with the controller. When SNESx9 was working it was playing fine with the controller too.

                          I'm a lil confused about what happened today. For some reason after trying all the above I tried to update/install snesx9 and it did not give me a choice to use binary so I tried source and it said the appropriate files were missing. So I tried to uninstall it and got the same message.

                          So now I started with a fresh Jessie install with Retropie and try again.

                          Which drivers are we supposed to be using? The PS drivers knock out my wifi so I've been using Xbox drivers. I don't know any thing about the other two.

                          1 Reply Last reply Reply Quote 0
                          • D
                            Duhjoker
                            last edited by

                            Got the fresh install going and installed

                            Lr-fceum ---------works
                            PCSX rearmed-------not working
                            Snexs9-----------working
                            Osmose---------not working
                            Mupen64-------not working
                            Reicasreicast -----not working

                            Only the NES and SNES controls are working

                            1 Reply Last reply Reply Quote 0
                            • T
                              TheGecko
                              last edited by

                              I can confirm this today - fresh install of Retropie, paired successfully with the FC30 Pro running 1.69 firmware. UDev script setup to run in background mode, Retropie runs off the controller fine. Tried using PCX, Neogeo and PC Engine emulators, no luck - the dpad works, but no buttons.

                              I'll give firmware 1.68 a go, and I'll try out the adjusted button assignments from above.

                              1 Reply Last reply Reply Quote 0
                              • T
                                TheGecko
                                last edited by

                                OK - Firmware 1.68 installed, and everything appears to be working now. I had to remove the controller in the bluetooth menu, then re-pair it. Reboot of retropie, and it all appears good now.

                                I also powered down/up the controller after the firmware downgrade, just to be sure.

                                1 Reply Last reply Reply Quote 0
                                • BuZzB
                                  BuZz administrators @Duhjoker
                                  last edited by BuZz

                                  @Duhjoker said in 8bitdo FC30pro not working in emulators:

                                  Why are my posts all in code squares ?

                                  Because you used a four space indent which can be used for code blocks. http://commonmark.org/help/

                                  To help us help you - please make sure you read the sticky topics before posting - https://retropie.org.uk/forum/topic/3/read-this-first

                                  1 Reply Last reply Reply Quote 0
                                  • First post
                                    Last post

                                  Contributions to the project are always appreciated, so if you would like to support us with a donation you can do so here.

                                  Hosting provided by Mythic-Beasts. See the Hosting Information page for more information.