NeoPiGamer
-
@Flavor - Looks like you're using a custom PCB. Did you design it or source it from someone else?
We produced it.
-
is there a power and ground for the controls on each half of the control pad? also how did you connect the display to the pi zero
-
Yes, each half of the remaining GBA PCB have their own ground pinouts located at the locations quoted in the previous post.
My previous post in this thread linked below explains how I modified, connected, and configured the display in great detail.
-
The shoulder button supports are a massive ground I conveniently used here.
-
Hi Tekkaman_Slade.
First. This is the most awesome gba transformation.
Second. I would like to ask few things since I am thinking of similar build. I am thinking of few possibilities how to suite my purpose and would like to know what you think about it.
-
cutting more of the original PCB.
Purpose is to make up more room. Do you see any possible problems except the need to replace the connection for common ground and the "mounting of more peaces of PCB". -
would be possible to show a but more pictures ? for example with the whole assembly together (battery...lcd on its place.. etc).
Thanks a lot for the reply.
Ondrej
-
-
I'm documenting my effort on my personal wiki, you can take a look here http://wiki.mrvanes.com/wiki/mrvanes/view/Raspberry+Pi/Advance+Zero/ for detailed pictures of my WIP.
-
@mrvanes
Thanks. Nice progress. Now it is back to the board to figure out how to add a joystick and perhaps a hubpiwi . Good luck with the finish of the build. Ill keep you guys up to date with the progress. thanks again.Ondrej
-
In addition to cutting out the middle/green portion of the original PCB, I also removed all of the capacitors to reduce the depth of the PCB as well. After that, there's isn't much else left to cut without ruining the board.
It's hard to take more pictures of the internals of the NeoPiGamer without completely taking it apart since the pi zero is connected to components in the front and the back of the unit. I'll see what I can do as I might be opening it up for some minor tweaks soon.
I'm looking forward to hearing more about your addition of a joystick. I'm considering doing the same on my next GBA build.
-
@agentKrowka I wouldn't go for a hubpiwi (had to google to see what it was) as you can dismantle a multiport usb port quite easily and have wifi optional if you create an external USB connector. Saves space and battery since I don't need wifi while gaming. Cascading USB hubs are no problem, so you can attach keyboard and wifi dongle to the hub'ed output.
I needed the hub because I prefer audio via (dismantled) usb audio plug as you can see. Has enough power to drive the speaker or headphones so no need for the tiny amp. -
@mrvanes Yeah I was thinking about the bat. life /space / cost. For now I want to try to use it if possible since I have one already laying around. But so far it proves to be a bit too big anyway. So now I am looking for the usb hub option. Something cheap and tiny to compare the size/bat. efficiency etc.
-
So, last week the mini micro JST 2.0 PH 2-Pin connectors arrived and I had the time to complete my GBA-Zero project. Nice touch is that I kept the battery compartment intact and now contains a home-made 2AA-cell Li-ion pack.
http://wiki.mrvanes.com/wiki/mrvanes/view/Raspberry+Pi/Advance+Zero/
Hope the pics may be of any help to anyone. Happy hacking! -
@mrvanes Nice visual build log! In the spirit of build logs, here's another a guy sent to me. https://pitendo.wordpress.com/2016/10/03/gamepie-advance-build/
-
@mrvanes By the way, could you post some more details (text and/or photos) of your X/Y button setup?
-
I don't have more pictures than what you see, only higher resolution. I had to build an elevated structure using perfboard to lift the microswithes above the GBA PCB, because I used the test pin connection for the A/B buttons situated there. Then I glued the 3DS X/Y buttons using 2 component glue to the microswitches. I had to drill out some support structure and remove the well gliders from the X/Y buttons.
Sometime, I will write some comments around the pics to clarify what I did, just don't hold your breath.
-
@mrvanes Hi. Great job man :) Interesting choice for the battery. Are those 2x 2500mah ? Did you had any chance to check how long they last in "real play" conditions ?
-
They're ordered as 2900 (per AA!), but I don't believe they have that much juice, or I destroyed them while soldering the pack. I get about 1-2 hr pure playtime on a full charge. I'll time it someday. I did tweak config.txt back to 30fps refresh for the piTFT overlay instead of 60 yesterday, so that may add some stamina? I also made a GBZero and that one lasted way longer on a single 2600 Adafruit LiPo.
-
@mrvanes Well if you went for 14500 Li-ions - I know what you mean. I am yet to meat a good quality bat. of that sort (they usually have around 900 mah :/ ) Maybe you could try to squeeze in some 16650 bat. But they are a bit too long as far as I can see.
I am trying to go with a 3.7v 3000mah flat lipo (64x48x8 mm) ... I think I cna fit it in if I rly try hard this weekend :D -
Yes, they're 14500's. I made the mistake of ordering 18650's (pack) before I knew the difference (I allways call them AA's when I buy alkalines). Was a bitter surprise when they arrived after 3 weeks transport. But why would they print/sell/advertise 2900 when it's actually 900 (apart from blatantly lying for profit)?
And yes, you will never fit 18650's in the GBA.
-
I was asking myself the same question and started to dig around to see if there is some similar bat. to AA size which would be better in terms of capacity .
Found this most helpful thing:
https://en.wikipedia.org/wiki/List_of_battery_sizesAs per this apparently the "common" capacity for 14500 Li-ion is 700-800 ... So I guess they print it there just for profit ...perhaps ? Honestly - no idea :/
One note.. Finding the best battery for the job was always a problem in all my projects that required batteries :/
Mostly ended up using li-po packs. But with them comes the problem ----- size. They are super nice and flat which is pretty much useless int his project since a 3000mah will be somewhere around (60 to 80) x (80 to 100) x (around 3.5) mm.
Best I found is 64x48x8 mm
http://www.ebay.com/itm/3-7V-3000-mAh-Polymer-rechargeable-Li-battery-For-GPS-DVD-PDA-Tablet-PC-814864-/121823784043?hash=item1c5d436c6b:g:5xMAAOSwn8FXRm~TThere is a option to take smaller capacity and make it as a pack 1s2p (1 series 2 parallel). Not good, since unbalance charging of parallel lipos is dangerous. So unless you find/make a suitable pack that you can take out and charge in external charger this option is useless.
Last option is to just find one fitting Li-po and go with the capacity that it provides. I think you can find a 2500mAh li-po that would fit your design (with some plastic cutting) .
If you figure out something different/better I would appreciate if you let us know.
-
I'm sticking with the 1s2p 14500 Li-ion pack I made, if not for the sole reason of aesthetics. I like the look of the blue pack that snuggly fits the original AA container ;)
Contributions to the project are always appreciated, so if you would like to support us with a donation you can do so here.
Hosting provided by Mythic-Beasts. See the Hosting Information page for more information.