How are you cooling your Pi 3?
-
Do you guys recommend using heatsinks and/or cases with fans, with a non overclocked pi?
Just want to know if I need to spend a little bit more money or not.
Btw, I'm thinkin of housing my pi in my old sega genesis, do you guys think it will overheat being closed on the shell of the genesis? -
@Thegodfather
You should be fine without any heating unless it's really cramped in there. -
The only cooling which really works (based on benchmark tests on youtube) is water cooling (overkill obviously) & a large heat sink which means you wont get the top of a case on. Everything else outside of that is a waste of time. I run a pi2 not over clocked and it runs everything.
-
@UberJay said in How are you cooling your Pi 3?:
The only cooling which really works (based on benchmark tests on youtube) is water cooling (overkill obviously) & a large heat sink which means you wont get the top of a case on. Everything else outside of that is a waste of time. I run a pi2 not over clocked and it runs everything.
Well, come on now. Just about any sink properly attached will help cool the CPU. I have not seen a single overheat indicator since I added a sink to my Pi3 and before that I was able to easily and consistently trigger temperature throttling by running newer arcade games.
-
@caver01 I think if your examination was more scientific ie. A before / after with stats on temp. You would find that no significant improvements are made unless you go above and beyond what fits in a standard case.
-
standard-size case that helps temps a lot.
there are also loads of other temperature experiments done with pi3s. these guys will throttle no problem without heatsinks, and often with.
anecdotally, my pi3 + heatsink (bigger than the 'ebay' one in that video) in my alu case keeps my temps down pretty low, but i'll still get throttling when i attempt a mame recompile, and that's with no overclock.
-
@UberJay said in How are you cooling your Pi 3?:
@caver01 I think if your examination was more scientific ie. A before / after with stats on temp. You would find that no significant improvements are made unless you go above and beyond what fits in a standard case.
I'm not sure I need to be more scientific. We could get into test data and define what you mean by significant, but we are merely after sufficient cooling. All I know is that I bought a Pi3 when they came out and saw throttling (red box appears, games stuttering, sound dropping etc.). I slapped on a heatsink (cut from an old Pentium sink) using thermal paste and viola--no throttling. In fact, I haven't seen a single instance of throttling since. Is it significant cooling? Depends on how you define it. Do I know how many degrees it has changed? No. I don't remember the temperature delta. Is it sufficient for a better gaming experience? Absolutely.
I don't want to sound overenthusiastic about it, but I think it's important to counter the argument that the only cooling that works is water cooling. That's simply not true. There may be people reading this that are seeing the red box and wondering what they can do about it. Everyone's mileage will vary as we all use different cases and what not, but you don't have to go crazy to see results. A properly applied sink can make an impact and can improve your gaming experience if you are seeing issues.
-
Here's my heatsink for sake of argument. It really doesn't take much to help an overheating problem. Also, I think you'd agree that this is a sink that will fit it practically every case made, although I don't use a case (mounted inside my arcade cabinet). That probably makes a difference too.
-
@UberJay said in How are you cooling your Pi 3?:
I run a pi2 not over clocked and it runs everything.
Interestingly, when I was running a Pi2 I didn't see any heat issues either, but when I upgraded to the Pi3, everything ran faster (and hotter). It may be apples and orange between the two.
-
I think this would be a better solution than your little heat sink.
-
@UberJay LOL! That's fantastic. I know it's an extreme example to prove the point, but it's not a contest to get the lowest temp--we just need enough cooling to stop the throttling. Besides, that one blocks access to gpio pins.
-
@caver01 I think we agree to be honest. I'm sure you are getting some benefits from your heat Sync and if it meets your requirements then it's obviously the right solution. Like you said it's not a competition but if it was this guy has won :)
-
@UberJay I do like the creative use of plastic to insulate and secure the sink. Mine is literally just sticking with the thermal paste, but I'd feel better if I had a method to hold it on there.
-
I think he did a follow-up video with a fan put on that thing as well... lol.
Anyway, from what I have seen, a heatsink only drops temps by a little bit (the normal ones you see for the RPi, not the beast above). Adding a fan is when it drops considerably.
-
I put 2 small copper heat sinks in my pi3 today. Total waste of time. I have to run the thing with the case cover off or it starts to throttle
-
@Ekstreme How small? Were they finned, or just slabs of copper?
-
Finned. but not tall enough I reckon.
I've just ordered a case with a fan. Enough of this mucking about -
I bought this from Ebay.
Huge difference for only $7US
-
@T1nmaN wow. The price is right. Seems like a no-brainer to get a case, heat sinks and a fan for that price. I like that the case was designed with GPIO, camera and display cable slots too. Is it acrylic? It would be easy enough to use acrylic weld solvent to attach "wings" with screw holes for mounting. Seems like a good solution if the fan doesn't conk out.
-
@caver01 Yeah, the one thing that is missing is screws and nuts to attach the board to the case, but it's a pretty tight fit, and I feel pretty good about it the way it is. Does anyone know what size nuts and screws would work? I can't remember if it had the holes to attach to the board at the bottom, but I'll check when I get home. It is acrylic.
Here's the ebay link : http://www.ebay.ca/itm/111965982816?_trksid=p2057872.m2749.l2649&var=410906661440&ssPageName=STRK%3AMEBIDX%3AIT
Contributions to the project are always appreciated, so if you would like to support us with a donation you can do so here.
Hosting provided by Mythic-Beasts. See the Hosting Information page for more information.