No sound retroflag gpi case with pi zero w 2 (Solved)

retropieuser555

@philcomm Here's there config file:-

############################################################################
# Boot loader configuration                                                #
# Warning: do not edit this file as it will be overwritten when upgrading! #
############################################################################

# Using /etc/modules is deprecated and no longer supported on 4.4 kernel
# So manually enable audio
dtparam=audio=on

# if you plug your tv at the same time as your rpi and that the rpi switches from the hdmi or
# give a low resolution because tv had no enough time to initialize it
boot_delay=3

# disable boot rainbow
disable_splash=1

# default CEC name
cec_osd_name=recalbox

avoid_safe_mode=1

kernel=boot/linux
initramfs boot/initrd.gz

# force hdmi while the tv can take time before sending the signal on the hdmi output
hdmi_force_hotplug=1

# total amount of GPU memory
gpu_mem_256=128
gpu_mem_512=128
gpu_mem_1024=448

# your settings can be set in /boot/recalbox-user-config.txt
include recalbox-user-config.txt

# overclocking settings are automatically managed in this file
# do not remove this line, nor edit the file
include recalbox-oc-config.txt

# Raise the first security limit up to 70° instead of 60° for pi3 and pi4
[pi3]
temp_soft_limit=70
dtoverlay=vc4-kms-v3d
include recalbox-crt-config.txt

[pi4]
temp_soft_limit=70
dtoverlay=vc4-kms-v3d
include recalbox-crt-config.txt

# disable 4k resolution
hdmi_pixel_freq_limit:0=200000000
hdmi_pixel_freq_limit:1=200000000

[board-type=0x12]
dtoverlay=vc4-kms-v3d

# custom config
[all]

They don't seem to be using the pwm-audio-pi-zero.dtbo overlay in the config and it isn't in the overlay folders at all. Any ideas how they got this working? Guess can go onto their forum and ask them

Philcomm

@retropieuser555 Does the /etc/asound.conf file exists? If yes, what's the content?

retropieuser555

@philcomm

pcm.monocard{
	slave.pcm "hw:0"
	slave.channels 2
	type route
	ttable {
		# Copy both input channels to output channel 1 (Right).
		0.1 1
		1.1 1
		# Copy both input channels to output channel 0 (Left).
		0.0 1
		1.0 1
		}
}

pcm.!default monocard

Thing is though, I don't know a great deal about recalbox, but it's not built on raspbian? Think if I used this in the retropie build it'll work?

Philcomm

@retropieuser555 said in No sound retroflag gpi case with pi zero w 2:

@philcomm
pcm.monocard{
	slave.pcm "hw:0"
	slave.channels 2
	type route
	ttable {
		# Copy both input channels to output channel 1 (Right).
		0.1 1
		1.1 1
		# Copy both input channels to output channel 0 (Left).
		0.0 1
		1.0 1
		}
}

pcm.!default monocard
Thing is though, I don't know a great deal about recalbox, but it's not built on raspbian? Think if I used this in the retropie build it'll work?

I will have to try later if that works

Slime1982

Hi, I have been struggling with the same issue, and have managed to solve it.

The issue is that by default the latest version of Raspbian disables the audio if nothing is connected to HDMI.

Use this one line entry in config.txt to fix it:

dtoverlay=audremap,pins_18_19,enable_jack=on

You don't need the pwm-audio-pi-zero.dtbo file and you can remove all the custom audio entries from Retroflag's config.txt and use this one line instead. (leave all the entries for the LCD in obviously).

The custom asound.conf file in recalbox is used to downmix stereo audio to mono, as the built in speaker on the GPi only outputs the right channel.

retropieuser555

@slime1982 Hey that's great news can you post your config.txt file please? I think I'm deleting the wrong lines out

Slime1982

@retropieuser555

Start with the stock config.txt and add this at the end:

#Pi Zero 2 W GPi Config
dtoverlay=audremap,pins_18_19,enable_jack=on
display_rotate=1
dtoverlay=dpi24
overscan_left=0
overscan_right=0
overscan_top=0
overscan_bottom=0
framebuffer_width=320
framebuffer_height=240
enable_dpi_lcd=1
display_default_lcd=1
dpi_group=2
dpi_mode=87
dpi_output_format=0x6016
#hdmi_timings=320 0 28 18 28 480 0 2 2 4 0 0 0 60 0 32000000 6
hdmi_timings=240 1 38 10 20 320 1 20 4 4 0 0 0 60 0 6400000 1

you still need Retroflag's dpi24.dtbo, but you don't need to copy the pwm audio overlay file.

The custom asound.conf file doesn't work, I suspect because the sound device is now referred to as headphones instead of pcm, but I'm working on it now.

Also, go into raspi-config, system options and in audio select 'headphones'. it should be the only option, but select it to ensure it is the default device.

Philcomm

@slime1982 Are you an angel? insert Anakin Star Wars GIF

Slime1982

@philcomm

Ha! no, just very determined!

However, it's not quite right yet. On testing with headphones, the L and R channels are swapped, so I've changed the line to

dtoverlay=audremap,pins_18_19,swap_lr

note that enable_jack=on does not appear to be necessary .

Still working on fixing asound.conf so both channels play through the GPi's speaker. I'll reply with an update when I figure it out.

retropieuser555

@slime1982 Almost there!

You're using their dpi25 overlay right? I'm getting some lines across the screen (but audio does work!)

MD5 (/Volumes/boot/overlays/dpi24.dtbo) = 55906663a9752f0588b74c407437dc16

Is that your md5 hash for your dpi24?

Philcomm

I'll try to make a PR to RetroFlag for these changes. I hope they have a repo for their GPi Patch

Slime1982

@retropieuser555

Hi, sorry, had to pop out.

Yes, that's the same file I'm using, the md5 matches :)

Lines on the screen might be a poor contact issue with the pogo pins.

Slime1982

@retropieuser555

Hi, sorry, I was testing with a stock Raspbian lite image earlier, I've moved to Retropie now. Do you mean you can see some of the boot text behind the splashscreen?

Comment out the line overscan_scale=1 in config.txt and also add these lines, which i neglected to include earlier:

avoid_safe_mode=1
disable_pvt=1
disable_audio_dither=1

That seems to fix it for me :)

Slime1982

OK, ignore everything I said about asound.conf. I was testing with Raspbian lite, it works perfectly in Retropie :D

So, I think that's it, we're up and running now!

retropieuser555

@slime1982 Heya yeah the screen lines is definitely specific to me, I left the gpi on for a few hours earlier and it's left some screen burn on the dpi screen itself. So a different problem but nothing relevant to this topic, the audio works, the video works and am happily testing out drastic, n64 and psp. It'll be interesting what we can push on this thing. Thanks again for the fix, we'll have to see if retroflag implement it and make it clear for pi zero2 this the way to go.

pumpytums

@slime1982
This works great thanks.

Can you SSH into your Zero 2 equiped GPI mine reboots everytime. Plays games fine though so doesn't sound like a power issue. Very odd indeed. I even put ssh.txt in the root keeps rebooting every time ssh is enabled.

retropieuser555

@pumpytums Is the file you made named ssh.txt you're putting into the boot folder? It needs to have no extension on the file, just called ssh

retropieuser555

This post is deleted!

pumpytums

@retropieuser555
I think this is an issue

fresh install of Retropie 24th October.
Retroflag default files
SSH in boot
wpa_supplicant.conf for WiFi setting

System boots then crashes. This problem occurs whenever SSH is enabled either via file method or through menu Raspi config.

Slime1982

@retropieuser555

Ah, yeah. I believe those lines will fade out eventually. I've done the same, left it on with no signal from the Pi, so you just get random lines on the screen. They burn in, but it seems to be temporary.