raspberry pi not booting into emulationstation

Devenhulk

This post is deleted!

Devenhulk

@IceChes1 i tried that but when i type in emulation station it just goes back to a black screen

mitu

You should add the rest of the information asked in https://retropie.org.uk/forum/topic/3/read-this-first.
What display are you using (TV/Monitor) ? Did you connect the HDMI cable into the 1st port (next to the USB-C power port) ?

Devenhulk

@mitu im using a monitor and yes i connected everything i can still use the terminal so i know i am getting a HDMI signal and the red light isn't blinking so i am pretty sure the power is good

mitu

@Devenhulk Can you run, from the terminal, tvservice -s and post the output ? What monitor are you using (model/vendor) ?

Devenhulk

@mitu im using a scripture monitor and a 128 gb SD

Devenhulk

@mitu yes i can it says state 0x6 {dvi custom rgb full 4;3} 640x480 60.00hz, progressive

mitu

im using a scripture monitor

Never heard of this and can't find any reference to it - can you be more specific ? Model number ?

Devenhulk

mb i meant to say Sceptre monitor E225W-1920

mitu

Post your config.txt - as it it now.

Devenhulk

For more options and information see

http://rpf.io/configtxt

Some settings may impact device functionality. See link above for details

uncomment if you get no picture on HDMI for a default "safe" mode
hdmi_safe=1

uncomment this if your display has a black border of unused pixels visible

and your display can output without overscan

#disable_overscan=1

uncomment the following to adjust overscan. Use positive numbers if console

goes off screen, and negative if there is too much border

#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

uncomment to force a console size. By default it will be display's size minus

overscan.

#framebuffer_width=1280
#framebuffer_height=720

uncomment if hdmi display is not detected and composite is being output

#hdmi_force_hotplug=1

uncomment to force a specific HDMI mode (this will force VGA)

#hdmi_group=1
#hdmi_mode=1

uncomment to force a HDMI mode rather than DVI. This can make audio work in

DMT (computer monitor) modes

#hdmi_drive=2

uncomment to increase signal to HDMI, if you have interference, blanking, or
no display
#config_hdmi_boost=4

uncomment for composite PAL

#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

Uncomment some or all of these to enable the optional hardware interfaces

#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

Uncomment this to enable infrared communication.

#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18

Additional overlays and parameters are documented /boot/overlays/README

Enable audio (loads snd_bcm2835)

dtparam=audio=on

[pi4]

Enable DRM VC4 V3D driver on top of the dispmanx display stack

dtoverlay=vc4-fkms-v3d
max_framebuffers=2

[all]
#dtoverlay=vc4-fkms-v3d
overscan_scale=1

mitu

Replace hdmi_safe with

hdmi_group=1
hdmi_mode=16
hdmi_drive=2

and see if you get a proper picture.

Devenhulk

okay ill try thanks

Devenhulk

@mitu i tried all 3 but when i try to boot up it doesn't Evan show that it finds a signal anymore so i switched it back to HDMI_safe

mitu

@Devenhulk Try choosing another video mode - see https://www.raspberrypi.org/documentation/configuration/config-txt/video.md. It's strange that for a monitor that claims to support 1080, setting the video mode to 1080p doesn't work.

EDIT: you can add

hdmi_force_hotplug=1
hdmi_ignore_edid=0xa5000080

to the previous lines, this will make the Pi ignore what your monitor sends in the EDID.

Devenhulk

@mitu k ill go try that

Devenhulk

@mitu i am sorry for the late reply been a little busy but when i type in those lines it still doesn't change that it boots up and there's a black screen i can still access terminal though but when i type in emulation station it just goes back to the black screen

Devenhulk

hey guys solved the problem it was the hdmi it needed to be closetest to the power

carbonatedwater

@Devenhulk Hi. What do you mean by this? I'm having the same problem, Retropie boots up, but then it just goes into a black screen when it goes into EmulationStation. I'm not really a Linux user, so I have no idea what is going on.
I'm using Retropie 4.8, on a Raspberry Pi 4. I've used my computer monitor and my TV.

superdan

@carbonatedwater Do you have any log while booting?