wolf4sdl black screen on launch, audio playing keyboard working

[BuZz]

@kaltertod please be more specific with details. Latest version isn't enough info.

Please do not post a support request without first reading and following the advice in https://retropie.org.uk/forum/topic/3/read-this-first

Also check dispmanx settings for wolf4sdl in RetroPie-Setup /
-> configuration / tools)

Should be enabled for RPI4

[kaltertod]

Dispmanx is enabled for wolf4sdl it is also kind of funny I cannot disable it either, runcommand.log shows no errors upon launch of the game... still have a black screen if you can point me to a log file that will give some information I will be happy to post it.

[kaltertod]

Pi = Rpi 4 4GB
Retropie Version = 4.6
Kernel Version = 5.4.51-v71+
Controller = Xbox One S & Keyboard
Usb Devices = Wireless Usb Keyboard Adapter (Logitech)
Error Messages = None /dev/shm/runcommand.log Shows no Errors

[kaltertod]

I have uninstalled and removed all game files from the /roms/ports/wolf3d directory, removed the /roms/ports/wolf3d directory and done a full reinstall of the the port and will see if this makes a difference.

[BuZz]

@kaltertod the log shows no errors or is empty?The log may still be useful to reproduce the issue.

If you still have the issue please post a log and also the contents of /boot/config.txt

[kaltertod]

Contents of the /boot/config.txt

---

For more options and information see

http://rpf.io/configtxt

Some settings may impact device functionality. See link above for details

uncomment if you get no picture on HDMI for a default "safe" mode

#hdmi_safe=1

uncomment this if your display has a black border of unused pixels visible

and your display can output without overscan

#disable_overscan=1

uncomment the following to adjust overscan. Use positive numbers if console

goes off screen, and negative if there is too much border

overscan_left=-60
overscan_right=-60
overscan_top=-60
overscan_bottom=-60

uncomment to force a console size. By default it will be display's size minus

overscan.

#framebuffer_width=1280
#framebuffer_height=720

uncomment if hdmi display is not detected and composite is being output

#hdmi_force_hotplug=1

uncomment to force a specific HDMI mode (this will force VGA)

#hdmi_group=1
#hdmi_mode=1

uncomment to force a HDMI mode rather than DVI. This can make audio work in

DMT (computer monitor) modes

#hdmi_drive=2

uncomment to increase signal to HDMI, if you have interference, blanking, or

no display

config_hdmi_boost=4

uncomment for composite PAL

#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

Uncomment some or all of these to enable the optional hardware interfaces

dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

Uncomment this to enable infrared communication.

#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18

Additional overlays and parameters are documented /boot/overlays/README

Enable audio (loads snd_bcm2835)

dtparam=audio=on

[pi4]

Enable DRM VC4 V3D driver on top of the dispmanx display stack

dtoverlay=vc4-kms-v3d-pi4,noaudio
max_framebuffers=2

[all]
#dtoverlay=vc4-fkms-v3d
overscan_scale=1
enable_uart=1
gpu_mem=512

[Overclocking]
over_voltage=6
arm_freq=2100
gpu_freq=750

[kaltertod]

Contents in dev/shm/runcommand.log

_________________________________________-

Parameters:
Executing: SDL1_VIDEODRIVER=dispmanx SDL_DISPMANX_WIDTH=720 SDL_DISPMANX_HEIGHT=480 SDL_VIDEO_KMSDRM_CRTCID=65 SDL_VIDEO_KMSDRM_MODEID=48 /opt/retropie/ports/wolf4sdl/bin/wolf4sdl.sh "/home/pi/RetroPie/roms/ports/wolf3d/vswap.wl1"

[mitu]

@kaltertod You've disabled the Pi4 fkms overlay and you're using the KMS only GPU driver. This is not a standard RetroPie config and that's why the game doesn't work - dispmanx is not available for your system.

[cyperghost]

@kaltertod Did you try ecwolf instead?
I made best experience with this mod therefore I wrote the script installer, sadly it wasn't accepted.
Main Thread is here - but consider also that what @mitu told you. As long you are not using a standard version it's hard to help.

[kaltertod]

I will try and go back to fkms and see what happens oddly it worked before....... and I will give ecwolf a shot

[kaltertod]

Disabled full kms driver and went back to fkms still no dice.... however, I uninstalled wolf4sdl and installed ecwolf and it now works flawlessly. Thanks Ghost I will mark this solved for now.