Hotkeys not working with XBOX one pads

mitu

@rad_schuhart said in Hotkeys not working with XBOX one pads:

Also as I said, when pressing the hotkey in Kodi, in the configuration pad screen, it is not recognized, but it is recognized by emulation station. Is there maybe anything wrong in the drivers?

Could be, xpadneo was recently upgraded to v0.9.1, that would be the change since 4.7.1 was released. Maybe the following change is at fault:

      hid-xpadneo: Send KEY_MODE for the Xbox button

You can grab the previous xpadneo version by downloading the previous xpadneo.sh and overwriting the one in $HOME/RetroPie-Setup/scriptmodules/supplementary, then re-installing the driver and rebooting.

NOTE: to reset back to the current RetroPie-Setup version (so updating will not give an error) run:

cd $HOME/RetroPie-Setup
git reset --hard

Rad_Schuhart

Hi Mitu, I am refloating this thread. I am still having the same issue. I gave it some months of time to see if the drivers update and the problem fixes itself, but no luck so far. Along this time, my children were able to exit the games using a wired XBOX 360 controller, but my youngest managed to break the pad and is not usable anymore. So at this point I need my wireless XBOX ONE controllers working.

I tried updating everything, and also tried with a 100% fresh install, and still have the same issue. Everything works but just no hotkey, so I cannot save, not load, and most important, not exit any game.

Any how-to idiots guide edition would be very appreciated. :(

Thanks in advance! I am sure it must be an easy fix.

mitu

@rad_schuhart I don't think the Xpadneo driver has had any radical updates this year or during the last 4 moths. It's still the best bet for an Xbox One controller, when used over Bluetooth.
Have you tried using the Select button as a hotkey ?

Rad_Schuhart

@mitu yep, I tried and still does not work. Any clue or anything I can check and post here?

mitu

@rad_schuhart You could post a verbose log for a libretro based emulator, just to check what configuration files are used. Use pastebin.com to post the log file's contents.

EDIT: post also the main RetroArch configuration file, from /opt/retropie/configs/all/retroarch.cfg.

Rad_Schuhart

@mitu Hi, sorry it took me some time to answer, I was at job.

And sorry again, but I need an idiots guide. I am totally lost now and I don't know how to do what you request me to do. I have been trying to solve the problem for long time, so now I am so saturated that I don't know even where to start.

Maybe you can access remotelly to it saving your precious time? I feel bad taking your time, seriously.

mitu

Not sure what I could add more than what's already explained in the documentation page I linked. What step is unclear ?

Rad_Schuhart

@mitu Well, almost everything is unclear for me. :(

Verbose log: First time I read those words, lol. In your link it says "When launching Libretro cores (those prefixed by lr-) the Runcommand launch menu presents the option to Launch with verbose logging. This outputs more information to the log file found in /dev/shm/runcommand.log which is useful, and often necessary, when diagnosing problems. Once the game is exited, the log file can be downloaded via SFTP or viewed directly via the command line."

Well, I don't know what is a libreretro core, and don't know how to launch it. Neither what SFTP is or what is the command line.

And about the retroarch configuration file, what should I type? I pressed F4 in the keyboard and wrote that: /opt/retropie/configs/all/retroarch.cfg. and did not work.

Yep, it seems as I said I need an idiots step by step guide. Like "Switch it on, go to retropie, raspi-config.... and so on" I am really sorry and also embarrased, but for some of us this is pretty much like chinese. :(

mitu

When you launch a game, then name of the game and the emulator used is shown in the Runcommand dialog (as shown in the documentation page). If the emulator name starts with lr- it means it's a libretro core.
A lot of the emulators included in RetroPie are libretro cores, in fact if you're using another type of emulator, this topic wouldn't make sense, since only RetroArch has the concept of hotkey.
So just launch your game, bring up the launch menu and enable verbose logging before starting, this will produce the log file.

As for how to view or retrieve the file: SFTP/SSH has a separate doc page, linked from the one I posted, which explains how to enable it and how to connect to your Pi via SFTP and transfer the log file to your PC and upload it to pastebin.com.

EDIT: you can also copy the log file to your roms folder after you run the game and then retrieve it vie file shares from your PC (by browsing \\retropie\roms). To copy the file, just exit EmulationStation and type at the command prompt:

cp /dev/shm/runcommand.log $HOME/RetroPie/roms/

Rad_Schuhart

@mitu said in Hotkeys not working with XBOX one pads:

\retropie\roms

Well, I think I half managed to do it. I launched the game with verbose logging, that was easy. Problem was I could not exit the game so later on when running that cp runcommand and so on, it did not work.

I had to launch the game with the broken xbox wired controller, and then I was able to retrieve the file and uploaded here in pastebin:

https://pastebin.com/WKfb3Smd

I guess is not what you need, and you have to see that file with the xbox one bluetooth controller, but if I cannot exit the game, no idea what to do.

mitu

Well, yes, without the Xbox controller plugged in - to see which configuration file it loads - the log is not so useful. You can use the Esc key on the keyboard to exit RetroArch if you have it plugged in, this way the controller detection and configuration info will show in the log.

On the other hand, just to check if my theory of RetroArch loading the wrong controller configuration file, can you check in the \\retropie\configs\all\retroarch-joypads file share and tell me what folders and files are present there ? There should be one .cfg file per controller you configured and no folders present. If you configured just 2 controllers in your setup, there should be just 2 .cfg files present.

Rad_Schuhart

@mitu
Quick update: I launched the game with the xbox one controller, switched it off, connected the xbox 360 one, exited the game and copied the file:

https://pastebin.com/xQhrXQWy

Maybe here you can find something

Rad_Schuhart

@mitu said in Hotkeys not working with XBOX one pads:

\retropie\configs\all\retroarch-joypads

There are 4 files, names are "Microsoft X-box 360 pad.cfg" and another that ends in bak.
And "Xbox Wireless Controller.cfg" and another that ends in .bak

mitu

@rad_schuhart said in Hotkeys not working with XBOX one pads:

Maybe here you can find something

The log doesn't show any controller being present. Did you upload the previous log by mistake ?

There are 4 files, names are "Microsoft X-box 360 pad.cfg" and another that ends in bak.

Ok.

Rad_Schuhart

@mitu I think I uploaded the new one, but I will try again later on, and Ill try exiting with the keyboard, but did not work last time I tried.

I have to go to work now, so Ill update again in 12 long hours, lol.

Rad_Schuhart

@mitu

Here I am, 12 hours later, lol. I think I managed to paste the correct file now. Hope you can see what is wrong there.
https://pastebin.com/5XtFWLCe

mitu

@rad_schuhart Unfortunately, there's no message showing which config file is loaded (if any) for the controller, though it appears that a controller is detected:

[INFO] [udev]: Added Device Keyboard#0   USB Keyboard (/dev/input/event0) .
[WARN] [udev]: Full-screen pointer won't be available.
[INFO] [udev]: Pad #0 (/dev/input/event3) supports force feedback.
[INFO] [udev]: Pad #0 (/dev/input/event3) supports 16 force feedback effects.
[INFO] [Joypad]: Found joypad driver: "udev".
[INFO] [Video]: Found display server: null
[INFO] ALSA: Using floating point format.

Do you have any additional driver installed - like xboxdrv ?

Rad_Schuhart

@mitu I just took a look: Retropie setup/manage packages/manage deiver packages/ only two appear as installed, and those are "xpadneo" and "xpad" both installed via source.

EDIT: I just tried unninstalling "xpad", restarted the system but the problem persist.

mitu

Thank I have no idea why the configuration is not loaded by RetroArch. You could try resetting its configuration to RetroPie's defaults, by copying retroarch.cfg.rp-dist over retroarch.cfg in the \\retropie\configs\all\ (do a backup first just in case).

If that doesn't work, I'm not sure what we could try.

Rad_Schuhart

@mitu I did it right now. There are some changes, for example now the main controller is the cross and not the stick, but still I cannot exit the game.

The only thing that I can say is I have this problem with both my xbox one controllers since I updated the system like one year ago, but it worked flawlessly (except in kody) for a long time. I have absolutelly no clue what to do :(