(GUIDE) How to add Ocarina of Time PC Port to Retropie (Pi5 64bit)

roslof

Enjoying this very much. Similar to the Mario 64 PC project. Thanks for providing the detailed steps!

@retropieuser555 said in (GUIDE) How to add Ocarina of Time PC Port to Retropie (Pi5 64bit):

Edit the below line, I used CONF_SWAPSIZE=1024

FWIW with this value, I still ran out of memory. With a large enough drive, would recommend boosting to 2048 to be safe.

Would also remove the -- -j4 at the end of each command-line for Bookworm.

Lastly, for things to work with the .sh files provided, note that the /opt/retropie/ports/soh folder should be pi:pi

sudo chown -R pi:pi /opt/retropie/ports/soh

Hope this helps.
-ros

Deityfierezy

So, I followed everything as said in here, the port opens and works just fine on raspbian, but when i try to run it trough retropie it just sends me back to the ports menu.

retropieuser555

@Deityfierezy So there might be some kind of error in the master branch, I re-tried it now with an earlier branch it worked out for me.

Maybe try this and see if it works for you:-

git clone https://github.com/HarbourMasters/Shipwright.git
cd Shipwright

git checkout 8.0.4 

git submodule update --init

retropieuser555

Also I have been testing out their Majora's mask Port and it also works. Same steps and dependencies as for Ocarina but after those then run this:-

git clone https://github.com/HarbourMasters/2ship2harkinian
cd 2ship2harkinian
git submodule update --init

Copy your Majora's mask .z64 rom into ORTExporter directory then run these:-

cmake -H. -Bbuild-cmake -GNinja
cmake --build build-cmake --target ExtractAssets
cmake --build build-cmake

As before copy the 2s2h.elf, 2ship.o2r & mm.o2r into /opt/retropie/ports/2s2h and create an .sh file that points towards it and the similar steps as before.

Only done a quick run around as the deku doing the first cycle but it seems to play pretty well

Majora's mask

nioh8

hey thanks for this, got it up and running on my pi5 with pi os, runs well. a bit off topic but this is the only relevant post i can find, is it possible to build the perfect dark PC port for the raspberry pi 5? i don't have the best knowledge with this stuff, was wondering if anyone has done it, thanks.

ExarKunIv

@nioh8 maybe
there is a Perfect Dark Decompilation on github, so there is a possibility that it could work.

nioh8

@ExarKunIv yea there’s a full fledged pc port here

https://github.com/fgsfdsfgs/perfect_dark

But I’m not well versed in compiling so was looking for some direction in how to build it

ExarKunIv

@nioh8 im someone can figure it out.
if i have time i can maybe mess with it. im trying to get the script for Ocarina of Time to work.
being a real bugger

ExarKunIv

@mitu i hate to tag you. but im out of ideas.

@retropieuser555 and I are trying to get a script working for the port above. and im seeing something i have not seen before.

here is the script
from what i can tell it is good and for the most part it works fine, but the thing is. it takes like 6 hours if it finishes

but if you run the command above it will take like 30 min. (i timed it)

what could be causing this issue. is there something in the background that RetroPie doing that would slow this down.
im very lost here

mitu

@ExarKunIv said in (GUIDE) How to add Ocarina of Time PC Port to Retropie (Pi5 64bit):

here is the script
from what i can tell it is good and for the most part it works fine, but the thing is. it takes like 6 hours if it finishes

but if you run the command above it will take like 30 min. (i timed it)

Pure guesswork, but running it from the script sets MAKEFLAGS to increase parallelism during build, which requires a great amount of RAM due to multiple threads compiling at the same time. The RAM requirement is so great, that it hits the SWAP, which is going to massively slowdown the compilation.

Running the commands by hand will use a single thread/CPU for compiling, lowering the RAM requirements and thus finishing sooner.

Btw, RetroPie already has a swap adding/removing function in helpers, there no need to invent another one.

EDIT: forgot to add. Modify the build function and unset MAKEFLAGS or set it to -j1, before the cmake commands are executed. See if that changes anything.

ExarKunIv

@mitu as always thank you for that insight. i will make the changes and see what happens

ExarKunIv

@mitu so adding the -j1 did the trick
j1 was slow so i changed the number, but its working

i just need a little help with the function rpSwap() i dont know how to set that up correctly

or is there a current script that already uses this that i can look at

mitu

@ExarKunIv said in (GUIDE) How to add Ocarina of Time PC Port to Retropie (Pi5 64bit):

i just need a little help with the function rpSwap() i dont know how to set that up correctly

openmsx and mame use that function. The only parameter is the amount of Mb you need, which the function allocates taking into account the existing RAM.

ExarKunIv

@mitu thank you. thats a big help