Retroflag Snes case
-
@chuck_b there’s a switch inside that sets it to safe power/shutdown or the symptom you are mentioning. Check to see if that switch is set to safe shutdown.
-
@jandalf81 you talk about the external switch, not the internal safe switch, right?
@lostless I don't have one, I'm asking before I buy it :)
-
Yeah, sorry. I could have expressed myself better here...
To clarify:
The case comes with an internal board, see http://retroflag.com/SUPERPi-CASE-J.htmlThere's two switches and one button on that board:
- POWER (ON / OFF)
- SAFE SHUTDOWN (ON / OFF)
- RESET
Also, the power is being routed through this internal board. So, I have set the SAFE SHUTDOWN to ON and installed the script from the official website https://github.com/RetroFlag/retroflag-picase
This way, the fan starts spinning when you set the POWER switch to ON (and doesn't stop while the Pi is powered on). The script will shut down the Pi and stop the fan when it detects the POWER switch being set to OFF.
-
@jandalf81 If you don't use the fan port on the pcb, will the shutdown scripts still work?
I'm having trouble using a fan on ports 17, 20 on the gpio. Fan works but hitting power button just turns the whole device off, with no safe shutdown.
-
-
@cyperghost ya, your script works great. Thanks
-
@cyperghost Does this work with 3B+? Cause I'm not getting safe shutdown.
-
@hurricanefan It works as long as you use RetroPie with ES. It is the same python code as retroflag uses with some improvements. I suggest to put the switch in correct position. So retroflag code uses killall command and then safe shutdown fails if an emulator is running. This avoids the script written by me.
-
@cyperghost I am using retropie 4.4 image with all packages updated, I have a pi 3b+ and the safe shutdown switch is set to ON. Any time I hit the power button it just kills all power to the device. No safe shutdown.
-
@HurricaneFan Is there a sudden powerdown like you pull the power cord? If no then try my script. If yes then the switch seems not working
-
@cyperghost Yeah, it acts like I totally powered down like a cord pull. I switched the python file to yours and I get the same behavior. So bad switch might be possible.
-
@hurricanefan I've read about wrong soldered switch, maybe you set safe shutdown to off and try this? Some users reported issues here
-
@cyperghost I tried putting the switch back to off and it doesn't work either. Its as if the switch doesn't do anything at all when its on.
-
Sounds like its something to do with pi 3b+ models.
-
@hurricanefan Do you have annother Pie? It's not the layout of the GPIOs or so... So I think it's rather something with the case.
-
@cyperghost I have a pi 3b thats screwed into another case. I'll try to test that shortly.
-
@jandalf81 said in Retroflag Snes case:
This way, the fan starts spinning when you set the POWER switch to ON (and doesn't stop while the Pi is powered on).
And Retropie starts only when I set the POWER SWITCH to ON. Correct?
-
@cyperghost So just finished testing with the same sd card and a pi 3b (not plus) and the safe shutdown and reset code works just fine. The pi 3b+ has something that doesn't like the shutdown/reset code. Super weird!!
-
@hurricanefan I have the retro flag case and using @cyperghost script and it’s working fine on my pi 3b+
-
@hurricanefan Please try following, the retroflag scripts enables UART for getting the power LED work
comment out or writeenable_uart=0from your/boot/command.txt/boot/config.txt
Contributions to the project are always appreciated, so if you would like to support us with a donation you can do so here.
Hosting provided by Mythic-Beasts. See the Hosting Information page for more information.