Xinmo Controller Config and Remote Access

mitu

As you probably discovered, to edit the file, just connect via SSH (you'll need to enable it first, it's in the docs) and run sudo nano /boot/cmdline.txt to add the necessary parameters.
Or you could take the alternate configuration path and add a configuration file for the kernel module by adding a .conf file in /etc/modprobe.d and adding

options usbhid quirks=0x0314:0x0328:0x040

to it.

rfxcasey

That command is not working, I notice the post at the bottom has 'usbhid quirks' while the first command listed is 'usbhid.quirks' which is correct? The first bit of code I addes as a line to cmdline.txt and rebooted but it still only sees my Xin mo as once controller. And the accompanying code after the '=' what is that, why is it different in the two posts and does it change based on which USB port your using?

mitu

@rfxcasey said in Xinmo Controller Config and Remote Access:

That command is not working, I notice the post at the bottom has 'usbhid quirks' while the first command listed is 'usbhid.quirks' which is correct?

That's not a command, but the contents of the modprobe configuration file, which has a different syntax than the kernel command line.

The first bit of code I addes as a line to cmdline.txt and rebooted but it still only sees my Xin mo as once controller. And the accompanying code after the '=' what is that, why is it different in the two posts and does it change based on which USB port your using?

No, it doesn't change based on the port. Post your cmdline.txt here, surrounded by code marks ( ``).

rfxcasey

OK will do, and sorry, yes I misspoke, but since you seem to know what you're doing is their any way we can chat instead or are such requests frowned upon here?

mitu

@rfxcasey I think you're missing the point of a forum.

rfxcasey

@mitu LOL! Oh, I know it's just a time thing. Anyways, awesome, I enabled SSH in RetroPi, wrote down the IP of the machine, plugged the IP into Putty making sure SSH was the protocol and BAM, I'm in like Flynn. Here's the contents of my /boot/cmdline.txy file:

dwc_otg.lpm_enable=0 console=serial0,115200 console=tty1 root=/dev/mmcblk0p11 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait loglevel=3 consoleblank=0 plymouth.enable=0
usbhid.quirks=0x16c0:0x05e1:0x040

mitu

@rfxcasey Did you add the usbhid.quirks=0x16c0:0x05e1:0x040 on the same line with the other parameters or on a separate line ? It should be on the same line - but from what your posted it looks like it's on the next line.

rfxcasey

@mitu Yes, the first two lines in my post are all on the same line as originally and I haven't touched that line, it's just the way it pasted in this reply box for the forum. The line I added is the last line and is also on it's own seperate line.

Took the liberty of running lsusb and here is the output:
pi@retropie:/ $ lsusb
Bus 001 Device 004: ID 046d:c52b Logitech, Inc. Unifying Receiver
Bus 001 Device 005: ID 16c0:05e1 Van Ooijen Technische Informatica Free shared USB VID/PID pair for CDC devices
Bus 001 Device 006: ID 0424:7800 Standard Microsystems Corp.
Bus 001 Device 003: ID 0424:2514 Standard Microsystems Corp. USB 2.0 Hub
Bus 001 Device 002: ID 0424:2514 Standard Microsystems Corp. USB 2.0 Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
pi@retropie:/ $

rfxcasey

@rfxcasey Oh, sorry just read what you typed again, yeah I put it on a new line as per the Wiki for retropi with Xin Mo https://github.com/RetroPie/RetroPie-Setup/wiki/Xin-Mo-Controller

rfxcasey

Oh, sorry just re read what you said, I'm God aweful tired. No it's not on the same line as you're saying it should be. I was just following the instructions found here. https://github.com/RetroPie/RetroPie-Setup/wiki/Xin-Mo-Controller

mitu

@rfxcasey the Wiki says:

Add the following to /boot/cmdline.txt -- just add a space to the end of the existing entry, so it is all on one line):

Where did you read to put it on a new line ?

rfxcasey

Ah, crap, I don't know, yeah I see it now, my brain is fried from work and lack of sleep. I don't know, somehow my brain saw add a new line, I think it was my dyslexia kicking in. Hold on and I'll fix it and hopefully I'll work now. JEEEZ, I need off of 3rd shift.

rfxcasey

AWESOME!!! Just testing it out, when I went into RetroPi configure controller it recognized it as 2 gamepads right away, configured each and was instantly playing some Street Fighter Alpha 3 with my 5 year old. I works great! Thanks for the help, should have notice my mistake, the devil is in the details as they say. I read so much I have developed a tendency to be lays and just speed read without even realizing I'm doing it. I my brain just saw 'add to it's own line' for some reason. Anyways the device should be included by default and hopefully this will be fixed in a new version so folks don't have mess with it manually. Guess my wiring job was spot on, I don't have any issues now. Thanks again.