Updating issues with RetroPie on RPi 4 issues?

jimmyjudd

@IceChes1 if you search the official Raspberry pi forum page (not retropie) there's a code you can run that will backdate your firmware on your pi. this will then allow you to overclock your GPU once more

IceChes1

Thank you so much.

djchewmacca

@mitu It's for those who with to dual boot their Pi with RetroPie. I have mine multibooted with multiple OSs. I'm using PINN which is a variant of NOOBs. When the official release of RetroPie is released I will be able to replace this dev build with the full version and keep my multibooted OSs as they are.

djchewmacca

@djchewmacca wish to dual boot*

George Spiggott

I've installed the latest weekly build (retropie-buster-4.5.11-rpi4.img.gz) and have discovered that my PS3 pad does not show up on bluetooth. This used to be an issue with retropie back in the summer? Is this still the same issue with the same fix? Or was it resolved and came back in the weekly builds?

Thread with the old problem.
https://retropie.org.uk/forum/topic/22312/latest-update-and-ps3-sixaxis-controller/81?_=1580935831242

mitu

@George-Spiggott I don't think it's the same problem, though the symptoms might look similar.
Try installing the latest test Raspbian Linux kernel/firmware with

sudo rpi-update

and then re-pair the controller via Bluetooth and see if there's any difference.

George Spiggott

@mitu Thanks. I've just tried that. No change. I have since removed and reinstalled sixaxis just to be sure it was't that. I still can't see the PS3 pad on bluetooth.

rejesterd

@George-Spiggott - Is the pad fully charged?

Try removing it and re-adding it from the command-line..

$ bluetoothctl remove <mac address of pad>
$ bluetoothctl connect <mac address of pad>

If that doesn't work, see if bluetoothctl can detect the pad..

$ bluetoothctl 
Agent registered
[bluetooth]# scan on
Discovery started
...

If it can discover other bluetooth devices but not the game pad, then there might be a discovery filter that's blocking it. To check it, do..

$ bluetoothctl 
Agent registered
[bluetooth]# menu scan
Menu scan:
Available commands:
-------------------
uuids [all/uuid1 uuid2 ...]                       Set/Get UUIDs filter
rssi [rssi]                                       Set/Get RSSI filter, and clears pathloss
pathloss [pathloss]                               Set/Get Pathloss filter, and clears RSSI
transport [transport]                             Set/Get transport filter
duplicate-data [on/off]                           Set/Get duplicate data filter
clear [uuids/rssi/pathloss/transport/duplicate-data] Clears discovery filter.
back                                              Return to main menu
version                                           Display version
quit                                              Quit program
exit                                              Quit program
help                                              Display help about this program
export                                            Print evironment variables
[bluetooth]# duplicate-data
DuplicateData: off

You can see mine is off, so there's no active filter. If yours is on, then try running the 'clear duplicate-data' and 'duplicate-data off' commands.

George Spiggott

Yes it is charged, I get a controller showing (shown below) when the pad is attached via a cable but I can't remove it.

[CHG] Controller DC:A6:32:51:52:36 Discovering: yes

I tried the scan but it did not pick up the pad. Duplicate data is off. There's a weekly update out today I'll see if that fixes it.

ByteThis

@George-Spiggott said in Updating issues with RetroPie on RPi 4 issues?:

Yes it is charged, I get a controller showing (shown below) when the pad is attached via a cable but I can't remove it.

[CHG] Controller DC:A6:32:51:52:36 Discovering: yes

I tried the scan but it did not pick up the pad. Duplicate data is off. There's a weekly update out today I'll see if that fixes it.

I've been having the same problem with my Wii U Pro controllers. They paired and worked fine on my Pi3B but I can't connect them on my Pi4. I tried on the Feb 7th version but haven't yet on today's update. Busy at the moment clearing all my stuff off the Pi3 to place on my Pi4.

mitu

@ByteThis I have a Wii U Pro controller and it's pairing without issues with the Pi4, configuration is fine and it works in RetroArch (that's the extent of my test).
The PS3 does not have native pairing - AFAIK - and it needs to be be first connected via USB to start the pairing - https://retropie.org.uk/docs/PS3-Controller/#using-the-retropie-setup-gui-to-configure-the-ps3-controller-bluetooth-connection-for-sixaxis.

ByteThis

@mitu said in Updating issues with RetroPie on RPi 4 issues?:

@ByteThis I have a Wii U Pro controller and it's pairing without issues with the Pi4, configuration is fine and it works in RetroArch (that's the extent of my test).

Thanks I will try it again when I have everything transferred over. Did you have it paired with the older versions of the weekly dev branch or the latest versions ?

mitu

@ByteThis said in Updating issues with RetroPie on RPi 4 issues?:

Did you have it paired with the older versions of the weekly dev branch or the latest versions ?

I installed the first dev image released and updated normally since then - updating the OS and packages in Raspbian along the RetroPie's installed packages.

davidgrohl

@IceChes1 said in Updating issues with RetroPie on RPi 4 issues?:

PSP games run very well.

Could you please tell me what core are you using for PSP and your configuration?
I'm tryng PSP but I cannot reach a smooth gameplay.
Thanks

IceChes1

I am using ppsspp, NOT lr-ppsspp with all default settings.

George Spiggott

Using PPSSPP here on a vanilla Pi4 at 2x resolution. It depends on the game. Medieval runs fine, GTA Vice City slows down when there's a lot on screen, Little big planet ran ok even on my vanilla Pi3B (1x resolution). Even overclocked I've never got the Tomb raider games to run smoothly consistently.

WODAK

@George-Spiggott said in Updating issues with RetroPie on RPi 4 issues?:

Using PPSSPP here on a vanilla Pi4 at 2x resolution. It depends on the game. Medieval runs fine, GTA Vice City slows down when there's a lot on screen, Little big planet ran ok even on my vanilla Pi3B (1x resolution). Even overclocked I've never got the Tomb raider games to run smoothly consistently.

Are you meaning running Tom Raider on PI3 or PI4. On PI4 it runs really good...both of them Anniversary and Legends.

George Spiggott

@WODAK on the pi4, alrhough I haven't tried overclocking rhe GPU on this build. Legend is jumpy and Anniversary slows down when the screen is busy, eg on the second level near the waterfall.

WODAK

@George-Spiggott said in Updating issues with RetroPie on RPi 4 issues?:

@WODAK on the pi4, alrhough I haven't tried overclocking rhe GPU on this build. Legend is jumpy and Anniversary slows down when the screen is busy, eg on the second level near the waterfall.

True...mine is overclocked... as for the game play....I didn't complete any level ... just tired to play a little bit moving, running around, learning how to play :)...etc...maybe for 5 minutes each...and it didn't have any hickups or anything.

George Spiggott

@WODAK How high is your GPU overclocked?