Neon Enhanced plugin for PSX

dre3ed

Ok so really strange situation,
Reinstalled retropie, did not put the bios in. PS1 game works fine. no freezes.
As soon as i copy over the SCHP001.bin into bios and enhance the gfx it starts freezing and crashing.

pcsx_rearmed_neon_enhancement_enable = "disabled"
pcsx_rearmed_neon_enhancement_no_main = "enabled"

If I have them like this, I have no crashes anymore or freezes, but the quality has dropped.

I tried overclocking the gfx, that didint help. I can actually hear the sound struggling when I put the enhancement on, as if the cpu isnt good enough.

dankcushions

This post is deleted!

dankcushions

sorry, misread. trying again:

@dre3ed said in Neon Enhanced plugin for PSX:

Ok so really strange situation,
Reinstalled retropie, did not put the bios in. PS1 game works fine. no freezes.
As soon as i copy over the SCHP001.bin into bios and enhance the gfx it starts freezing and crashing.

bios should be in uppercase, and be called SCPH1001.BIN. crashes are probably due to the issues i mentioned previously: https://retropie.org.uk/forum/post/68747

pcsx_rearmed_neon_enhancement_enable = "disabled"
pcsx_rearmed_neon_enhancement_no_main = "enabled"

If I have them like this, I have no crashes anymore or freezes, but the quality has dropped.

that's a pointless setting as you've disabled the enhancement, but enabled the speed hack for the enhancement. i don't even know what that would do.. probably nothing.

I tried overclocking the gfx, that didint help. I can actually hear the sound struggling when I put the enhancement on, as if the cpu isnt good enough.

overclocking GPU is pointless as pcsx is done purely on the the CPU. you're just adding more instability. i think your CPU is downclocking due to overheating, overclock or power - the same things that likely causing pi to crash it to crash.

dre3ed

I have heatsinks on every chip and a fan blowing on them plus an LCD display with temp monitor.
running between 36 and 46 degrees max. So its not that.

the bios upper case? when i go into the \RETROPIE folder the bios file is like this SCPH1001.bin isnt that uppercase?

I will now try and only overclock the cpu... cannot understand this is not working for me and working for others.

BuZz

@dre3ed said in Neon Enhanced plugin for PSX:

I have heatsinks on every chip and a fan blowing on them plus an LCD display with temp monitor.
running between 36 and 46 degrees max. So its not that.

PSU ?

the bios upper case? when i go into the \RETROPIE folder the bios file is like this SCPH1001.bin isnt that uppercase?

no - .bin is lowercase

dankcushions

@dre3ed

I have heatsinks on every chip and a fan blowing on them plus an LCD display with temp monitor.
running between 36 and 46 degrees max. So its not that

isn't what? an overclock doesn't have to be hot to be unstable. it just has to be overclocked. remove all overclocks if you have any instability.

dre3ed

ok so the psu is the official raspberry pi 3 one. 2.5a with 5.1v.
ordered it before yesterday thought it was that. But it helps anyway with powering controllers the 2.5a 5.0v wasnt good enough i had the bolt from time to time.

The .BIN is correctly in uppercase.

dre3ed

So I removed the overclock, it plays but then I can hear the sound starting to struggle and slow downs in the games. I will try a cpu overclock now. I'm running out of ideas.

dre3ed

just for info my config.txt looks like this by default without me doing anything. Anybody see anything wrong ?

For more options and information see

http://rpf.io/configtxtreadme

Some settings may impact device functionality. See link above for details

uncomment if you get no picture on HDMI for a default "safe" mode

#hdmi_safe=1

uncomment this if your display has a black border of unused pixels visible

and your display can output without overscan

disable_overscan=1

uncomment the following to adjust overscan. Use positive numbers if console

goes off screen, and negative if there is too much border

#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

uncomment to force a console size. By default it will be display's size minus

overscan.

#framebuffer_width=1280
#framebuffer_height=720

uncomment if hdmi display is not detected and composite is being output

#hdmi_force_hotplug=1

uncomment to force a specific HDMI mode (this will force VGA)

#hdmi_group=1
#hdmi_mode=1

uncomment to force a HDMI mode rather than DVI. This can make audio work in

DMT (computer monitor) modes

#hdmi_drive=2

uncomment to increase signal to HDMI, if you have interference, blanking, or

no display

#config_hdmi_boost=4

uncomment for composite PAL

#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

Uncomment some or all of these to enable the optional hardware interfaces

#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

Uncomment this to enable the lirc-rpi module

#dtoverlay=lirc-rpi

Additional overlays and parameters are documented /boot/overlays/README

Enable audio (loads snd_bcm2835)

dtparam=audio=on
gpu_mem_256=128
gpu_mem_512=256
gpu_mem_1024=256
overscan_scale=1
dtparam=i2c_arm=1

BuZz

@dre3ed please put configs in a code block or use external pastebin site. Click compose button for help in editor.

dre3ed

sorry!
I will in futur do that, my bad!
¨
Ok so I tried overclocking to 1300mghz, a bit faster game play but crash after a bit temps are still 44.., at 1372mghz overclock pretty good game play but still some slow downs then crash

BuZz

@dre3ed Please can you edit your post and do it, so it's readable.

Have you made sure your lr-pcsx-rearmed is up to date? Please can you post your complete retroarch-core-options.cfg and /opt/retropie/configs/all/retroarch.cfg file.

Please disable all overclocking for testing/debugging of any emulator issues.

BuZz

@dre3ed Also why is this discussion happening here, when you have another topic open for it ? https://retropie.org.uk/forum/topic/9273/retropie-in-game-freezing

dre3ed

ok so basically i put the resolution to CEA-34 - 1920x1080 @ 30hz 16.9 clock: 74mhz progressive and it didnt freeze anymore. I can notice thought that the screen isnt just kinda as fast as 60hz or at least its not as good. What would be the optimal or max resolution ?

dre3ed

apologise again, as I am new to the hole forum world I was not sure where to write, I just found this article online.

dankcushions

@dre3ed the default.

the neon enhancement can easily cause minor slowdowns regardless of overclock. without a video of what you get it might just be normal.

dre3ed

how does the code block work ? i click compose it says this forum is powered by ?

dre3ed

@dankcushions ok thank you, i guess I might have to remove it then.
Sorry about the code block thing, i dont know how to do it.

thank you all for your help and sorry for not respecting the rules.

dre3ed

BUT, to all those who have had the same problém as me, I am pretty sure I worked out the problem now. It's the resolution.

I am now running with neon enhancements but I changed the default resolution to 640x480 at 60hz no more slow downs no more freezing no more crashing. I will keep trying other resolutions until i find the max.

So there we go.

BuZz

@dre3ed is says Markdown This forum is powered by Markdown. For full documentation, click here - if you click here it tells you how to use markdown.

for code blocks put three backticks ``` above and below the block