Best way to output SCART (RGB) from Pi 3?

Dochartaigh

@maxriptide said in Best way to output SCART (RGB) from Pi 3?:

@Dochartaigh it looks like scaling artifacts, do you have overscan enabled in config.txt?

I did have overscan settings on to shrink the image - but something else was also messed up so I started with a fresh /boot/config.txt). I just tried the "Pixel Perfect" settings, versus the "Full Screen" and the Pixel Perfect is definitely more clear.

My problem, in part, is definitely the overscan. With it turned on (which I was using to shrink the image since it was way too large) the image gets all blurry. Is there any other way to shrink the image besides tweaking the overscan settings in /boot/config.txt? (or besides changing the settings on the monitors themselves - which are set perfect for the actual consoles hooked up to them)

edmaul69

@Dochartaigh the correct way to shrink and expand is to use the overscan up, down, left, and right. Adjust those until you get the right size and position. You can use positive and negative numbers (ie: 5, -5) to get it shrunk to the size you need.

maxriptide

@edmaul69 using overscan with such small resolution (320x240) always lead to scaling artifacts which are what Dochartaigh is experiencing

maxriptide

@Dochartaigh said in Best way to output SCART (RGB) from Pi 3?:
Is there any other way to shrink the image besides tweaking the overscan settings in /boot/config.txt?

@Dochartaigh you can try the settings I suggested to you in this thread and try to center the image following the method suggested by Molhoy in this thread: https://retropie.org.uk/forum/topic/8673/how-to-center-image-of-retroarch-with-pi-outputing-240p-rgb-via-hat-board-gert-666-to-pvm/14

Dochartaigh

Hi Gents, so if I'm hearing you both correctly (please let me know if I'm not!), there is NO other way to SHRINK the image via software settings BESIDES overscan, right?

Overscan, like Max said, totally ruins the image quality, so I'm hoping there's something else to try. Centering is perfect (thanks to that post - even tested it with the 240p Test Suite on NES, SNES, and Genesis!).

mikechi2

You guys might want to check out this:

https://discord.gg/gCvP6

Kevin has been doing some great work getting the scaling settings right using a high horizontal resolution (1600 x 240) which eliminates non-integer scaling artifacts.

He using my component video output to a TV but the same theory should apply if you're using SCART on a PVM.

maxriptide

@mikechi2 Thanks mikechi, I have to try it!

riggles

I'm really interested in a solution to this as well, got my raspberry pi + pi2scart today and can't get it to look nice without having to use black bars at 240p, is it possible to resolve these issues with a future update or modification to retropie+retroarch? Or is it a limitation inherent to the Raspberry Pi ( 3 model B ) itself? If it's not, would it be possible that we can change resolutions on the fly in the future like when using retroarch on a modded wii with rgb scart? That would be the dream!

@mikechi2 Would love to check the discord out, the invite ran out.

On a side note, NES scrolling backgrounds with any of the cores stutters for me, both through hdmi (720 and 1080p )or on a crt in 1:1 240p. Is this due to me using an ipad power supply? It's rated 2.4A. It says I'm getting a solid 60fps (60.2) but it's noticeably lagging compared to the same game on a wii which is buttery smooth. Settings seem optimal, no shader, smoothing etc, messed with both vsync and threaded video, if I apply a 2x phosphor shader when playing in 720p performance still stays exactly the same, also the backgrounds stutter irregularly.
Should I wait for my 3A micro usb psu or install an older version of retropie, surely there's no need to overclock for NES is there?

edmaul69

@riggles phone chargers are terrible to use because they dont run a constant voltage. The way fast charging works is it runs at a high voltage and the drops and runs at a slower voltage then goes back up to higher voltage. Buy a power supply made for the pi 3.

mikechi2

@riggles

Take a look at the second half of the video when super metroid starts. We figured out a good solution that matches the original console without introducing scaling artifacts. It should work on all the various DPI based adaptors.

I'm planning on making another video this weekend with some detailed instructions. Stayed tuned...

riggles

@mikechi2 Looks amazing and big thanks for sharing, going to wait until then to mess around with the pi2scart in that case :D

A Former User

Hi folks, 1st post here...

I just received my Pi2SCART. Connected everything and unfortunately the IQ is abysmal - it looks like RF, lots of noise. I suspect that it might be a fault of the RGB cable I bought - its awful, the clamps that secure connector casing to the cable both fell off instantly and now its all wobbly, colours change when the cable is moved. I bought it as a bundle with the Pi2SCART from Arcade Forge so Im surprised it`s so shoddy.

Now, Im an experienced PC user but this is my first time with the Pi, hence Id appreciate if you had a look at my checklist and see if I maybe missed a step or detail. I`ll get another cable anyway of course.
I followed the most common guides from RGBCables, HiScoreBob, Pi2Jamma, Arcade Forge and RPi homepage. What I did:

-assembled the unit (Pi + Pi2SCART)
-formatted a MicroSD, wrote images (RetroPie, later tried Lakka and the one from Arcade Forge)
-edited the config.txt adding the settings from Arcade Forge page
-connected power (original charger), Dualshock 3 via USB, RGB cable to my SONY Trinitron CRT, got the MicroSD in

The image is stable however extremely noisy - just like an RF connection. I have PS1 and Wii connected via RGB to this TV and IQ is superb, so its not the TVs fault. I havent tried any actual roms or emulators yet - however I suspect that even the frontend should be noise-free.

Any help/comments appreciated. Apart from the cable, I was thinking, maybe I need to update the firmware (though I just got this Pi from PiHut). Or maybe I missed something obvious.

EDIT: some bizarre highlights in red in the above post - not sure how that happened :/

Dochartaigh

Can you post some photos of the image so we can see exactly what you're talking about? You might also be better off on their FaceBook page for troubleshooting info - they're very well versed in their own product and offer great help (RetroPie, while great, is very much geared towards HDMI TV's).

mikechi2

@arkive Double check your power supply - are you getting the yellow low voltage warning? When I designed my adapter I had a lot of issues with picture noise and dimming due to lower supply problems.

Dalton69

@mikechi2 Arcadeforge settings are for 320x240 so the GUI will not look any good at all at that resolution. You can try the pixel theme it works a little bit better but we really lack a low resolution theme.

A Former User

Thanks for replies folks,

@Dochartaigh - I decided to post here because I saw posters who might have Pi2SCART & CRTs and some experience with it - and maybe could see if I missed some obvious step. I'm not on Facebook, but will try to pester AF's customer support if this is unresolved. Can't post pics because the damned cable actually fell apart completely after I pulled it out from the Pi yesterday - ridiculous :) But, the "noise" is akin to static you see on hardware connected through RF socket...think "film grain" filter you get in some modern games (not sure if it`d be even possible to capture on camera, these things are rather tricky)

I`ve just ordered a new cable anyway, will see if this problem persists. Hopefully not...if yes, it means that either Pi2Scart or the Pi itself is borked :/

@mikechi2 - " the yellow low voltage warning"? Hmm, not sure, but don't think so - I read somewhere the warning manifests itself as a square in the top right corner...can't recall seeing anything like that (can't test again because that damn cable is busted). Do you mean yellow LED? I see the green-ish LED (next to the red) blinking, but it looks like it`s reading from SD (maybe). Also, I got the original Pi power thingy, so hopefully this is not the case...though the symptoms (noise/dimness) match.

@Dalton69 - yes, I'm aware of that GUI theme limitation but that's something to be expected when outputting to a CRT (got similar "problems" on Wii emus) - however I don't think the noise I describe above should be present at all, even in the frontend GUI.

Will wait for the new cable, see what happens then. Thanks again.

Dochartaigh

@arkive said in Best way to output SCART (RGB) from Pi 3?:
the "noise" is akin to static you see on hardware connected through RF socket...think "film grain" filter you get in some modern games

This topic isn't letting me scroll up (I might have posted this before), and without a picture I still really don't know exactly what you're seeing, but try these settings for the Pixel Perfect mode. You can either do it by hitting Select+X in a game to enter the RetroArch settings (remember to save if they work for you), or through the RetroPie menu, RetroArch settings.

Before doing the above settings, mine was kinda muddy, blurry almost, some diagonal lines were a little wavy, just not as clean as my actual video game consoles were at all. After trying those above settings it's razor sharp on my BVM's (actually too sharp almost!).

A Former User

Okay...back on topic, with a new SCART cable. The good news is that the noise/interference problem is gone - it was indeed the cable's fault. The bad news - well, obviously now I`m facing the real battle, namely how on Earth do I get this thing to scale properly?

Some of you here - OP especially - already have been through this trial of fire, and I'm hoping could help me out a bit. To be honest, the amount of configs & variables is fairly overwhelming, even to somebody who manages a mostly-stable modded Skyrim setup ;)

There's lots of info scattered here and there regarding the topic, quite a few helpful posts here in this thread, however I`m starting from absolute scratch, since it's my first venture into pixel-perfect RGB world. Back in the day I happily didn't care - just plugged in any console via anything better than RF (mostly composite) and was content with the result. Not anymore...

Ok, to recap, here's what I'm doing: I have a RPi3 B connected to a 27" Sony CRT TV via Pi2Scart, running Retropie 4.2.
For starters, I`d like to display a SNES game in native resolution. Here are changes to cfg files I attempted:

config.txt

uncommented:

disable_overscan=1

added:

disable_audio_dither=1
dtparam=audio=on
dtoverlay=vga666
enable_dpi_lcd=1
display_default_lcd=1
dpi_group=2
dpi_mode=87
hdmi_timings=320 1 16 30 34 240 1 2 3 22 0 0 0 60 0 6400000 1

or

hdmi_timings=256 1 8 17 21 224 1 7 10 24 0 0 0 60 0 4800000 1

retroarch.cfg for SNES

aspect_ratio_index = "22"
custom_viewport_width = "256"
custom_viewport_height = "224"

Some retroarch.cfg video entries

video_threaded = "true"
video_smooth = "false"
aspect_ratio_index = "0"
video_aspect_ratio_auto = "true"
video_shader_enable = "false"
video_allow_rotate = "true"
video_windowed_fullscreen = "false"
video_crop_overscan = "false"
video_scale_integer = "true"
video_force_aspect = "true"
video_shared_context = "false"
auto_screenshot_filename = "true"
video_force_srgb_disable = "false"
video_fullscreen = "true"
video_vsync = "false"
video_hard_sync = "false"
video_post_filter_record = "false"
video_aspect_ratio = "-1.000000"
video_scale = "3.000000"
video_refresh_rate = "60.000027"

The effect is far from perfect - the screen is filled, but mostly cut off at bottom and left , depending on which hdmi_timings and "overscan_" values used (best pic I managed to get was using the timings from AForge and trimming (adding?) 16 to overscan left & bottom - filled, but with small black bars on top and bottom). And there`s an annoying stutter in scrolling games too.

Sorry for the long post but can`t see any way to hide these configs via html here. Any help most appreciated. And, @Dochartaigh, the PixelPerfect settings you mentioned did help you out, did you use them in Lakka or RetroPie?

riggles

@arkive does the scrolling stutter go away when different non pixel perfect or non full screen settings are used? How does it scroll on an hdtv? In my case it was just bad usb cable.

mediamogul

@arkive

can`t see any way to hide these configs via html here.

"put small logs in code blocks - see http://commonmark.org/help/ - and put large logs on a pastebin type site like http://paste.ubuntu.com/ http://pastebin.com/ or similar."

Quoted from:

https://retropie.org.uk/forum/topic/3/read-this-first