Not recognising keyboard or joypads

Riverstorm

Where is it not recognized? Are you sitting at the Emulationstation emulator selection menu?

When it first boots it immediately jumps to "Configure Input" did you have a device plugged in before you powered on the Pi and then you should configure at least one input device to navigate Emulationstation.

If you skipped that part I am not sure if that option comes back on the next reboot or if their are default keys assigned for the keyboard/controller if you skip it to bring up the Start menu. I have never tried it.

BuZz

you can't skip it unless you have configured an input device.

Riverstorm

@BuZz said in Not recognising keyboard or joypads:

you can't skip it unless you have configured an input device.

Ok, thanks Buzz for the clarification. I was wondering and wasn't feeling quite ambitious enough to load a fresh image just to see if I could "break it" sort to speak. :)

cryin-assassin

Hi thanks for the replies.
It's actually at the configure input screen where nothing happens.
I loaded another image and upon boot could see a USB device not supported error. So pretty sure the keyboards are my issue.

Just need to grab a cheap USB keyboard to test. Will keep let you know how I get on.

Thanks again
Nick

BuZz

Make sure you have sufficient power for the RPI also if using USB devices.

cryin-assassin

OK so after a new Power supply 5V 2A i am still in the same situation
Actual error I am receiving is -
device not accepting address 4 ( when booting to Raspbian to test)

I have tried 3 Keyboards - and 2 Joypads on the Retropie menu all not recognized.
I have also tried a few USB cables I had read the cable could be at fault.

Next step is to try a different Micro USB to USB lead ....

Meneer Jansen

@cryin-assassin said in Not recognising keyboard or joypads:

OK so after a new Power supply 5V 2A i am still in the same situation
Actual error I am receiving is -
device not accepting address 4 ( when booting to Raspbian to test)

I have tried 3 Keyboards - and 2 Joypads on the Retropie menu all not recognized.
I have also tried a few USB cables I had read the cable could be at fault.

Next step is to try a different Micro USB to USB lead ....

How do you boot into Raspbian? Doesn't that need some sort of input from you? Is there really NO inputdevice what so ever that your PiZero accepts input from? If that is so: I'd check my micro-USB to USB cable like you said....

cryin-assassin

It boots to a load/install image screen with no input, TBH I only tried that as I thought my RetroPie install may have been at fault my end.
Yep no USB device is recognized, so when I get home I shall try another micro USB adapter .... Fingers crossed :)

Riverstorm

@cryin-assassin said in Not recognising keyboard or joypads:

It boots to a load/install image screen with no input

Any chance you can snap a pic of your screen and post it? I am not sure what screen you're referring to but it might help in the troubleshooting. I am guessing since you have no keyboard you can't grab logs and I don't think it has Wifi by default?

cryin-assassin

I can grab a picture of the Raspbian boot error message this eve, strangely Retropie gives no error message on boot but still no USB device is recognized.

Confusing me a tad, but joys of these little projects.

cryin-assassin

Apologies , I cannot grab any log files as no Keyboard and no Wifi as yet.
Thanks
Nick

cryin-assassin

Ok finally she recognized the Keyboard :)
The issue was the Micro USB to USB adapter.

Thanks for all the suggestions guys, I can now move on with this project.
Nick

Riverstorm

@cryin-assassin said in Not recognising keyboard or joypads:

Ok finally she recognized the Keyboard :)
The issue was the Micro USB to USB adapter.

Thanks for all the suggestions guys, I can now move on with this project.
Nick

That's great, good luck! :)