Can't load retropi using terminal command: emulationstation

[Birdrat]

Pi Model: Pi 4 model B - 4gb
Power Supply: Default Pi ac supply
Version: Linux raspberrypi 5.4.35-v7l+ #1314 SMP Fri May 1 17:47:34 BST 2020 armv7l GNU/Linux
USB Devices connected: Bluetooth keyboard
Controller used: Ps3
Error messages received:

libEGL warning: DRI2: failed to authenticate
• failed to add service - already in use?

Config.txt file:

For more options and information see

1. # http://rpf.io/configtxt
2. # Some settings may impact device functionality. See link above for details
3.  
4. # uncomment if you get no picture on HDMI for a default "safe" mode
5. #hdmi_safe=1
6.  
7. # uncomment this if your display has a black border of unused pixels visible
8. # and your display can output without overscan
9. disable_overscan=1
10.  
11. # uncomment the following to adjust overscan. Use positive numbers if console
12. # goes off screen, and negative if there is too much border
13. #overscan_left=16
14. #overscan_right=16
15. #overscan_top=16
16. #overscan_bottom=16
17.  
18. # uncomment to force a console size. By default it will be display's size minus
19. # overscan.
20. #framebuffer_width=1280
21. #framebuffer_height=720
22.  
23. # uncomment if hdmi display is not detected and composite is being output
24. hdmi_force_hotplug=1
25.  
26. # uncomment to force a specific HDMI mode (this will force VGA)
27. hdmi_group=2
28. hdmi_mode=58
29.  
30. # uncomment to force a HDMI mode rather than DVI. This can make audio work in
31. # DMT (computer monitor) modes
32. #hdmi_drive=2
33. hdmi_force_hotplug=1
34. #hdmi_force_edid_audio=1
35.  
36. # uncomment to increase signal to HDMI, if you have interference, blanking, or
37. # no display
38. #config_hdmi_boost=4
39.  
40. # uncomment for composite PAL
41. #sdtv_mode=2
42.  
43. #uncomment to overclock the arm. 700 MHz is the default.
44. #arm_freq=800
45.  
46. # Uncomment some or all of these to enable the optional hardware interfaces
47. dtparam=i2c_arm=on
48. #dtparam=i2s=on
49. #dtparam=spi=on
50.  
51. # Uncomment this to enable infrared communication.
52. #dtoverlay=gpio-ir,gpio_pin=17
53. #dtoverlay=gpio-ir-tx,gpio_pin=18
54.  
55. # Additional overlays and parameters are documented /boot/overlays/README
56.  
57. # Enable audio (loads snd_bcm2835)
58. dtparam=audio=on
59.  
60. [pi4]
61. # Enable DRM VC4 V3D driver on top of the dispmanx display stack
62. dtoverlay=vc4-fkms-v3d
63. max_framebuffers=2
64.  
65. [all]
66. dtoverlay=vc4-fkms-v3d
67. enable_uart=1
68. gpu_mem=512

How to replicate the problem: Terminal command: emulationstation

[BuZz]

@Birdrat how did you install RetroPie?

[Birdrat]

@Buzz I am running raspian and did watching a ETA prime video on youtube.

Using the commands sudo git clone--depth=1 https://github.com/Retropie/RetroPie-Setup

cd retroPie-Setup

sudo nano retropie_packages.sh

Add this line _platform=rp3

sudo ./retropie_setup.sh

[BuZz]

@Birdrat that's not correct information I'm afraid. You should download an image from our site and use that.

[Birdrat]

@BuZz is that the same as running retropi on raspian or is that a boot direct into the retropi image?

I was hoping to have the option to run raspbian and retropi.

Can you please send the instructions link for correct image and install?

[BuZz]

@Birdrat it's raspbian yes (without desktop but that can be installed). Image and a link to the instructions are on the download page. Or click docs on the forum.

[Birdrat]

@BuZz, It appeared to have worked after a uninstall of my previous set up and following your link for the manual install.

Cheers. Would you recommend any settings that I should change for a raspberry pi 4 for a better experience?