Pi Zero W GBA [BUILD]
-
Is this one good?
-
@techieandroid
That one looks good to me. -
@techieandroid yeah thats the baby!!
-
@alulagoa said in Pi Zero W GBA [BUILD]:
@techieandroid
That one looks good to me.@moosepr said in Pi Zero W GBA [BUILD]:
@techieandroid yeah thats the baby!!
Okay thanks guys I got it.
Should come soon. Then I can finish building it. :)
I've got my live stream setup so I'll stream it live when I begin building it.
FWIF I think some will watch. -
@moosepr
Okay so I've got and setup the new screen but I don't like it at all. I don't know if this can be tweaked (probably, I just haven't tried yet) but the screen's dpi is messed up (everything it too small, which is probably just a wrongly set resolution from before when I had a tv connected), and the other major problem is it stutters so bad I can't play any game on it (it stutters, drops frames and tears). -
@hex I would disagree with this, I have one from Ebay which I converted to 5v and I think its junk, the contrast is poor, and when you have white pixels on a black background you get ghosting across that whole horizintal line of pixels, not the mention that the screen gets incredibly hot.
it is also poor resolution,
yes it works for gaming, just about, but if you are going to invest a good amount of time then I would try to get a better screen. -
@spruce_m00se Can you show a comparison photo/video?
Sent from 20,000 leagues under the sea.
Powersaver Emulation station : https://github.com/hex007/EmulationStation
ES dev script : https://github.com/hex007/es-dev/blob/master/es-tests.sh -
@hex I can show a photo at some point, but annoyingly the usb hub i built into the gameboy isnt compatible with keyboards, grrrr, that means that I need to desolder it and conenct a keyboard for some config as I had an urgent money making project (a lotof money ) last month and needed a micro sd urgently, so I robbed the one from the gameboy. now I have to reinstal the gpio pin controller setup before I can play again,
-
@spruce_m00se Some point is fine.
Sent from 20,000 leagues under the sea.
Powersaver Emulation station : https://github.com/hex007/EmulationStation
ES dev script : https://github.com/hex007/es-dev/blob/master/es-tests.sh -
@hex what would you like to see? the ghosting? or would you like to see the actual screen?
-
I have a photo of the LCD driver board, the circled white components are Caps that get super hot, I tried to put a ceramic cap alongside them to filter out any high frequency ripple, it didnt really do anything.
the whole thing gets so hot that it softens the hotglue thats holding it in place, and the individual caps get too hot to touch, -
I think you have a short or you have not converted it properly. My LCD board used to do that when I connected to the wrong terminal. Now it runs between room temp and warm. I can keep my finger on the chipset for extended periods.
Sent from 20,000 leagues under the sea.
Powersaver Emulation station : https://github.com/hex007/EmulationStation
ES dev script : https://github.com/hex007/es-dev/blob/master/es-tests.sh -
This screen you've been talking about is not the one we've been using in the build. Information not pertaining to this topic belongs in a different thread.
-
@techieandroid if you change the fbtft.config and set the speed to be 80000000 (7 zeros) and add FPS=60
That should improve things
-
@moosepr
Okay cool, thanks I'll try it out. -
@moosepr
The resolution is defaulted at 720x480, which is probably why it looks bad, I'm going to go into the config and change that to the actual resolution of the screen. -
@moosepr
I set it to speed=90000000 fps=60 after testing it a lot and like these settings. I was wondering what resolution settings I have to choose from that applies to this screen and not the HDMI, like, I guess this screen would be analog (I don't really know I haven't looked at the spec sheet yet). I'm just trying to set everything to 320x240 which is what the screen is. Also I'm curious about changing the overscan since it appears to be off. Will that mess anything up with this screen? -
@hex Do you have a link for a conversion tutorial? I have simply soldered the 5v input to the old output of the voltage regulator that I removed, in thoery everything after the voltage regulator is still seeinng the same voltage as before.
-
@spruce_m00se Kindly create a new thread and tag me. This is getting off topic
Sent from 20,000 leagues under the sea.
Powersaver Emulation station : https://github.com/hex007/EmulationStation
ES dev script : https://github.com/hex007/es-dev/blob/master/es-tests.sh -
@hex hold on, hahahaha
Contributions to the project are always appreciated, so if you would like to support us with a donation you can do so here.
Hosting provided by Mythic-Beasts. See the Hosting Information page for more information.