Configure 2 identical controllers differently

mitu

@xadox That's not what you're telling in the first post - even if they're seen as an USB receiver, you say they're recognized as Microsoft X-Box 360 Pad. Are you running xboxdrv by any chance ?

xadox

Yes. What I told in the first post its correct.
If I connect one of the Receivers without a Controller paired to them the following is shown (in this case under Ubuntu 16.04, no Pi around):

usb 2-2.1: USB disconnect, device number 4
usb 2-2.1: new full-speed USB device number 5 using uhci_hcd
usb 2-2.1: New USB device found, idVendor=045e, idProduct=028e
usb 2-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-2.1: Product: 8Bitdo Receiver
usb 2-2.1: Manufacturer: 8Bitdo Receiver   
usb 2-2.1: SerialNumber: Receiver     
input: Microsoft X-Box 360 pad as /devices/pci0000:00/0000:00:11.0/0000:02:03.0/usb2/2-2/2-2.1/2-2.1:1.0/input/input7

So the system recognises the Receivers as Microsoft X-Box 360 pad.
The xboxdrv is not installed.

mediamogul

@xadox, @mitu

At little history to @xadox's issue can also be found here. When you last wrote you noted that you were able to use a udev rule to create a unique symlink. To my knowledge, the only way to differentiate the two would be to have a different ID name. The only way I know how to do that would be to map a new virtual controller to one of the physical ones and assign a unique ID name there. I have a specific note on how to achieve this using xboxdrv, but you may be able to find a similar solution with other software.

xadox

@mediamogul Yeah. I thought it would be better to create an own thread for this.
I gave up with the udev rule, since I was not able to find enought information for this.

I think I will give the xboxdrv a try and will read your FAQ first.

mediamogul

@xadox said in Configure 2 identical controllers differently:

think I will give the xboxdrv a try

You might first see if you can discover any other possible solutions for changing the ID name. xboxdrv will definitely do the job, but it's a bit like taking a howitzer to a housefly.

xadox

@mediamogul Learing never hurts :)

Besides maybe I could also solve the problem with the 8BitDo SN30 PRO that the left and right trigger buttons are not working in ES or RetroArch.

grant2258

delete the config that getting used or move it somewhere safe so there is no conflict

xadox

@mediamogul After some problems in getting rc.local running on Ubuntu 16.04 I was able to create the configs for the two Receivers.

Both Receivers are getting individual Names and Configs in ES an RR, now.
The problem with the trigger buttons on the SN30 Pro could be solved, also.

But I have no clue how to start xboxdrv with the configs for the two Receivers at once. I am only able to start xboxdrv for one controller at once.

mediamogul

@xadox

Without seeing the script I can only guess, but it could be that xboxdrv is trying to call out to the same controller twice due to it having the same name. If this is the case, you could repeat the trick you were using earlier to create a unique symlinked event with a udev rule and point one of the xboxdrv launch instances to it. For troubleshooting, I always like to manually launch my xboxdrv instances from a terminal where I can view and correct any errors before I move them into a script.

xadox

@mediamogul At the moment I am starting xboxdrv manually from terminal.

/opt/retropie/supplementary/xboxdrv/bin/xboxdrv \
--evdev /dev/input/by-path/pci-0000:02:03.0-usb-0:2.1:1.0-event-joystick \
--silent \
--detach-kernel-driver \
--deadzone-trigger 15%	\
--deadzone 4000	\
--device-name "8BitDo SFC30" \
--evdev-absmap ABS_X=dpad_x,ABS_Y=dpad_y \
--evdev-keymap BTN_EAST=a,BTN_SOUTH=b,BTN_WEST=x,BTN_NORTH=y,BTN_TL=lb,BTN_TR=rb,BTN_SELECT=back,BTN_START=start \
--dpad-only \
--ui-axismap lt=void,rt=void \
--ui-buttonmap tl=void,tr=void,guide=void \
--evdev /dev/input/by-path/pci-0000:02:03.0-usb-0:2.2:1.0-event-joystick \
--silent \
--detach-kernel-driver \
--force-feedback \
--deadzone-trigger 15%	\
--deadzone 4000	\
--trigger-as-button \
--device-name "8BitDo SN30 Pro" \
--evdev-absmap ABS_X=x1,ABS_Y=y1,ABS_RX=x2,ABS_RY=y2,ABS_Z=lt,ABS_RZ=rt,ABS_HAT0X=dpad_x,ABS_HAT0Y=dpad_y \
--evdev-keymap BTN_EAST=a,BTN_SOUTH=b,BTN_WEST=x,BTN_NORTH=y,BTN_TL=lb,BTN_TR=rb,BTN_THUMBL=tl,BTN_THUMBR=tr,BTN_MODE=guide,BTN_SELECT=back,BTN_START=start \
&

But xboxdrv only creates the first virtual controller.
The second one is beeing ignored.

Starting xboxdrv two times with each config does not work, since I am only able to start the process once.

mediamogul

@xadox

See if they'll work in this format

sudo /opt/retropie/supplementary/xboxdrv/bin/xboxdrv \
--evdev /dev/input/by-path/pci-0000:02:03.0-usb-0:2.1:1.0-event-joystick \
--silent \
--detach-kernel-driver \
--deadzone-trigger 15%	\
--deadzone 4000	\
--device-name "8BitDo SFC30" \
--evdev-absmap ABS_X=dpad_x,ABS_Y=dpad_y \
--evdev-keymap BTN_EAST=a,BTN_SOUTH=b,BTN_WEST=x,BTN_NORTH=y,BTN_TL=lb,BTN_TR=rb,BTN_SELECT=back,BTN_START=start \
--dpad-only \
--ui-axismap lt=void,rt=void \
--ui-buttonmap tl=void,tr=void,guide=void \
&

sudo /opt/retropie/supplementary/xboxdrv/bin/xboxdrv \
--evdev /dev/input/by-path/pci-0000:02:03.0-usb-0:2.2:1.0-event-joystick \
--silent \
--detach-kernel-driver \
--force-feedback \
--deadzone-trigger 15%	\
--deadzone 4000	\
--trigger-as-button \
--device-name "8BitDo SN30 Pro" \
--evdev-absmap ABS_X=x1,ABS_Y=y1,ABS_RX=x2,ABS_RY=y2,ABS_Z=lt,ABS_RZ=rt,ABS_HAT0X=dpad_x,ABS_HAT0Y=dpad_y \
--evdev-keymap BTN_EAST=a,BTN_SOUTH=b,BTN_WEST=x,BTN_NORTH=y,BTN_TL=lb,BTN_TR=rb,BTN_THUMBL=tl,BTN_THUMBR=tr,BTN_MODE=guide,BTN_SELECT=back,BTN_START=start \
&

xadox

@mediamogul Working, thx!

mediamogul

@xadox

Ah, nice. Glad to hear it.

xadox

Using xboxdrv solves most of the problems I had.
But now there are other problems occuring because of xboxdrv.

Because xboxdrv creates a virtual gamepad, RR does not use it at first place.
So I hat to switch the controller in RR.

Another problem is the hotkey button. While the buttons seems to be mapped correctly in RR it does not work right.
Pressing B, START, X directly uses the hotkeys instead of the normal button press.
I was able to solve this after setting the hotkey button again in RR.

@mediamogul Like you already mentioned. It makes the whole configuration more complicated. Always have to remeber or make a note of it how xboxdrv was configured :)

I will search on another solution without the use of xboxdrv.

mediamogul

@xadox said in Configure 2 identical controllers differently:

I will search on another solution without the use of xboxdrv.

If you find anything, please post back. I'm always interested in alternatives to these types of problems.