Juyao Dual Arcade 2 player on Ubuntu

mitu

@Dennis said in Juyao Dual Arcade 2 player on Ubuntu:

if i run that from the terminal it says path does not exist..

Yes, it's missing a letter:

cat /proc/bus/input/devices

Dennis

@mitu ahhhh lol.. i also have a xbox one hooked up:
I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button"
P: Phys=PNP0C0C/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
U: Uniq=
H: Handlers=kbd event0
B: PROP=0
B: EV=3
B: KEY=10000000000000 0

I: Bus=0019 Vendor=0000 Product=0003 Version=0000
N: Name="Sleep Button"
P: Phys=PNP0C0E/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
U: Uniq=
H: Handlers=kbd event1
B: PROP=0
B: EV=3
B: KEY=4000 0 0

I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button"
P: Phys=LNXPWRBN/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
U: Uniq=
H: Handlers=kbd event2
B: PROP=0
B: EV=3
B: KEY=10000000000000 0

I: Bus=0019 Vendor=1283 Product=0000 Version=0000
N: Name="ITE8713 CIR transceiver"
P: Phys=
S: Sysfs=/devices/virtual/rc/rc0/input8
U: Uniq=
H: Handlers=kbd event3
B: PROP=0
B: EV=100017
B: KEY=fff 0 4200108fc32e 237605100000000 0 700158000 419200004001 8e968000000000 10000000
B: REL=3
B: MSC=10

I: Bus=0003 Vendor=045e Product=02d1 Version=0203
N: Name="Microsoft X-Box One pad"
P: Phys=usb-0000:00:14.0-2/input0
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb2/2-2/2-2:1.0/input/input9
U: Uniq=
H: Handlers=event8 js0
B: PROP=0
B: EV=20000b
B: KEY=7cdb000000000000 0 0 0 0
B: ABS=3003f
B: FF=107030000 0

I: Bus=0019 Vendor=0000 Product=0006 Version=0000
N: Name="Video Bus"
P: Phys=LNXVIDEO/video/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input10
U: Uniq=
H: Handlers=kbd event9
B: PROP=0
B: EV=3
B: KEY=3e000b00000000 0 0 0

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH Mic"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1b.0/sound/card0/input11
U: Uniq=
H: Handlers=event10
B: PROP=0
B: EV=21
B: SW=10

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH Headphone"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1b.0/sound/card0/input12
U: Uniq=
H: Handlers=event11
B: PROP=0
B: EV=21
B: SW=4

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH HDMI/DP,pcm=3"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1b.0/sound/card0/input13
U: Uniq=
H: Handlers=event12
B: PROP=0
B: EV=21
B: SW=140

I: Bus=0003 Vendor=0314 Product=0328 Version=0110
N: Name="D_R_M JUYAO Dual Arcade"
P: Phys=usb-0000:00:14.0-1/input0
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb2/2-1/2-1:1.0/0003:0314:0328.000E/input/input26
U: Uniq=
H: Handlers=event4 js1
B: PROP=0
B: EV=1b
B: KEY=3fff000000000000 0 0 0 0
B: ABS=30027
B: MSC=10

I: Bus=0003 Vendor=046d Product=c077 Version=0111
N: Name="Logitech USB Optical Mouse"
P: Phys=usb-0000:00:14.0-3.1/input0
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb2/2-3/2-3.1/2-3.1:1.0/0003:046D:C077.000F/input/input27
U: Uniq=
H: Handlers=mouse0 event5
B: PROP=0
B: EV=17
B: KEY=70000 0 0 0 0
B: REL=903
B: MSC=10

I: Bus=0003 Vendor=03f0 Product=034a Version=0110
N: Name="Chicony HP Elite USB Keyboard"
P: Phys=usb-0000:00:14.0-3.4/input0
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb2/2-3/2-3.4/2-3.4:1.0/0003:03F0:034A.0010/input/input28
U: Uniq=
H: Handlers=sysrq kbd event6 leds
B: PROP=0
B: EV=120013
B: KEY=1000000000007 ff9f207ac14057ff febeffdfffefffff fffffffffffffffe
B: MSC=10
B: LED=7

I: Bus=0003 Vendor=03f0 Product=034a Version=0110
N: Name="Chicony HP Elite USB Keyboard System Control"
P: Phys=usb-0000:00:14.0-3.4/input1
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb2/2-3/2-3.4/2-3.4:1.1/0003:03F0:034A.0011/input/input29
U: Uniq=
H: Handlers=kbd event7
B: PROP=0
B: EV=13
B: KEY=c000 10000000000000 0
B: MSC=10

I: Bus=0003 Vendor=03f0 Product=034a Version=0110
N: Name="Chicony HP Elite USB Keyboard Consumer Control"
P: Phys=usb-0000:00:14.0-3.4/input1
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb2/2-3/2-3.4/2-3.4:1.1/0003:03F0:034A.0011/input/input30
U: Uniq=
H: Handlers=kbd event13
B: PROP=0
B: EV=1f
B: KEY=3f000300ff 0 0 483ffff17aff32d bf54444600000000 1 130f938b17c000 677bfad9415fed 9ed68000004400 10000002
B: REL=1040
B: ABS=100000000
B: MSC=10

mitu

Ok, so this looks according to the docs about this controller:

I: Bus=0003 Vendor=0314 Product=0328 Version=0110
N: Name="D_R_M JUYAO Dual Arcade"
P: Phys=usb-0000:00:14.0-1/input0
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb2/2-1/2-1:1.0/0003:0314:0328.000E/input/input26
U: Uniq=
H: Handlers=event4 js1
B: PROP=0
B: EV=1b
B: KEY=3fff000000000000 0 0 0 0
B: ABS=30027
B: MSC=10

If you run cat /etc/modprobe.d/rp-usbhid-quirks.conf (assuming this is the module options file you created with nano), what's the output ?

Dennis

@mitu said in Juyao Dual Arcade 2 player on Ubuntu:

cat /etc/modprobe.d/rp-usbhid-quirks.conf

options usbhid quirks=0x0314:0x0328:0x040

ps: something that makes it maybe weirder... my friend has a raspberry pi and it works on that... also works on windows (using a different emulator) but i got a mini pc with ubuntu i want to add in my arcade cabinet

mitu

@Dennis said in Juyao Dual Arcade 2 player on Ubuntu:

options usbhid quirks=0x0314:0x0328:0x040

This looks correct, matching your device. I don't know why this isn't applied. You can check if the quirks parameter is applied by running

cat /sys/module/usbhid/parameters/quirks

I assume you've rebooted the system after adding the file.

Dennis

@mitu when i run that it gives me:
(null),(null),(null),(null)

ps: i used this to install retropie:
https://markontech.com/linux/how-to-install-retropie-on-ubuntu-tutorial/

mitu

@Dennis said in Juyao Dual Arcade 2 player on Ubuntu:

@mitu when i run that it gives me:
(null),(null),(null),(null)

This means the quirks didn't apply. It's strange - I wonder if the usbhid module is built-in. What version of Ubuntu are you using ?

Dennis

@mitu Ubuntu 18.04.3 LTS, the latest.. clean install yesterday
do I need to run the terminal as admin?

mitu

Usually, if there's something needing admin rights - like loading/unloading module - it'e enough to add sudo before the command to run it as admin.

I don't have any more ideas what to check.
You can manually unload the driver (sudo rmmod usbhid), then load it with the quirks parameter set

sudo modprobe usbhid quirks=0x0314:0x0328:0x040

then check again if your encoder is detected as 2 gamepads.

Dennis

@mitu said in Juyao Dual Arcade 2 player on Ubuntu:

sudo modprobe usbhid quirks=0x0314:0x0328:0x040

you sire... are my new GOD!!... thank you so,so much... this DID the trick... it shows as 2 players AND no more spastic movement in menu! I need to get roms on there and see if all still works.. but i will let you know!

thanks a million times

mitu

.. this DID the trick ..

The command should be the equivalent of setting the module options (usbhid.quirks) with the .conf file, so I don't understand why it's not working via configuration, but it works from the command line (?).

Dennis

@mitu yeah it does, but does this mean i have to run it each time? Because that wouldn't be the best lol

Isn't the problem the line I added?
options usbhid quirks=0x0314:0x032..... etc
Because via the command line I did not use the 'options' text

mitu

@Dennis said in Juyao Dual Arcade 2 player on Ubuntu:

Because via the command line I did not use the 'options' text

The syntax is a bit different between the .conf file and the command line options, but the effect should be similar - I've tested it on an Ubuntu 18.04 installation, just like yours.

Can you double check if the options file is the correct path (file is in /etc/modprobe.d) and extension (.conf) ? If the options file is not correctly created, then the options won't apply automatically. If that's not the case, then you'll probably need to find a way to run the commands I posted earlier on each boot.

Dennis

@mitu yeah just checked and the file is 100% there.... it is read only btw and user is root... is that the problem.. i even tried adding another conf file without the rp- part.... i dont understand :(

Can't I add the line to another file and if yes, do you know how? Could it be the retropie install way I tried? See the url above which steps i used

mitu

@Dennis said in Juyao Dual Arcade 2 player on Ubuntu:

Can't I add the line to another file and if yes, do you know how? Could it be the retropie install way I tried?

No, the RetroPie installation doesn't affect the this part. Now that I'm thinking about it, there is another way - similar to how it's done for the PI: add the arguments to the boot loader (grub). See how it's done here - add the usbhid.quirks=0x16c0:0x05e1:0x040 fragment to GRUB_CMDLINE_LINUX_DEFAULT then run update-grub and reboot.

Dennis

@mitu this totally worked!!! thanks!!! b/c of new years eve and all I dont have time now to test a ROM and see if the controls work... on my friends Pi the controls worked in the menu but not in game... I will let you know!

thanks again so much and have a save and happy new year

Dennis

So, both controls are recognized! But now the controls do not work in game for player 1... in the menu I can use all the buttons but when starting a game only the right side of the arcade controls, so player 2 work.... nothing on the left arcade buttons work... also I couldnt exit out of the game for some reason... very weird.. any idea?

Dennis

Got of working via the retroarch mania thanks again for the amazing help

delbetu

@dennis Thanks for asking, answers were really helpful to me.
I have the same Juyao Dual Arcade Joystick and I faced the same issue that you had.

My dual controller was recognized as one controller so I wasn't able to configure them separately.

My solution was this:

cd /opt/retropie/configs/all/retroarch-joypads
cp Xin-Mo Xin-Mo Dual Arcade.cfg D_R_M JUYAO Dual Arcade.cfg

then edited D_R_M JUYAO Dual Arcade.cfg
replacing vendor and product_id

the final file should look similar to this:

input_device = "D_R_M JUYAO Dual Arcade"
input_driver = "udev"
input_vendor_id = "0314"
input_product_id = "0328"

input_up_axis = "-1"
input_down_axis = "+1"
input_left_axis = "-0"
input_right_axis = "+0"

input_select_btn = "7"
input_start_btn = "12"

input_a_btn = "0"
input_b_btn = "3"
input_x_btn = "5"
input_y_btn = "2"
input_l_btn = "1"
input_r_btn = "4"

input_l2_btn = "9"
input_r2_btn = "8"

input_l_x_plus_axis = "+0"
input_l_x_minus_axis = "-0"
input_l_y_plus_axis = "+1"
input_l_y_minus_axis = "-1"

After doing that, I was able to configure them separately on retroarch.