Failed to build emulationstation-kids

BuZz

@timbellomo You are low on memory. Are you sure you have a RPI3. Looks more like you have a 256 or 512MB Raspberry Pi 1 -depending on split. (in which case you should lower gpu split to 32 for compiling probably).

What's the output of cat /proc/cpuinfo ?

timbellomo

if I don't have a Pi 3, i'm going to have some strong words with MicroCenter.

processor       : 0
model name      : ARMv7 Processor rev 4 (v7l)
BogoMIPS        : 76.80
Features        : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm crc32
CPU implementer : 0x41
CPU architecture: 7
CPU variant     : 0x0
CPU part        : 0xd03
CPU revision    : 4

processor       : 1
model name      : ARMv7 Processor rev 4 (v7l)
BogoMIPS        : 76.80
Features        : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm crc32
CPU implementer : 0x41
CPU architecture: 7
CPU variant     : 0x0
CPU part        : 0xd03
CPU revision    : 4

processor       : 2
model name      : ARMv7 Processor rev 4 (v7l)
BogoMIPS        : 76.80
Features        : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm crc32
CPU implementer : 0x41
CPU architecture: 7
CPU variant     : 0x0
CPU part        : 0xd03
CPU revision    : 4

processor       : 3
model name      : ARMv7 Processor rev 4 (v7l)
BogoMIPS        : 76.80
Features        : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm crc32
CPU implementer : 0x41
CPU architecture: 7
CPU variant     : 0x0
CPU part        : 0xd03
CPU revision    : 4

Hardware        : BCM2709
Revision        : a22082
Serial          : 0000000068e065c1

BuZz

You do, but you don't have the right amount of free ram. Are you sure about your gpu split ?

Please post me the contents of your /boot/config.txt

timbellomo

Thanks for your help... sorry for the delay. I'm in the middle selling a house and haggling with real estate agents:

pi@retropie:~ $ tail /boot/config.txt

# Enable audio (loads snd_bcm2835)
dtparam=audio=on
#gpu_mem_256=128
#gpu_mem_512=256
#gpu_mem_1024=256
overscan_scale=1

program_usb_boot_mode=1
gpu_mem=32

BuZz

All of it please. Also the output of uname -a.

timbellomo

sorry...

/boot/config.txt:
http://pastebin.com/hpba4CQ1

uname -a:
Linux retropie 4.4.26-v7+ #915 SMP Thu Oct 20 17:08:44 BST 2016 armv7l GNU/Linux

BuZz

@timbellomo please sudo apt-get update; sudo apt-get dist-upgrade to update firmware/kernel. then boot up and do free again.

BuZz

The full output of dmesg would be useful too. thanks.

timbellomo

dmesg:
http://pastebin.com/1GGexvsR

note: i was building again, but Ctrl+C'd it to run the upgrade

BuZz

Something's definitely wrong - did you update the firmware/kernel via rpi-update at any point ?

[    0.000000] Memory: 111528K/131072K available (6348K kernel code, 432K rwdata, 1716K rodata, 476K init, 764K bss, 11352K reserved, 8192K cma-reserved)

Let's see when you have updated to the current firmware/kernel

BuZz

Are you running a standard RetroPie image downloaded from our site or something custom ?

timbellomo

i burned retropie-4.1-rpi2_rpi3.img. 99% sure from your site. But as I said, I'm running it 100% off of USB, without any SD card. After dist-upgrade it doesn't boot at all anymore :/. Nothing on screen

BuZz

@timbellomo I've not done any booting off USB, but you will want to probably request for help from raspberrypi.org forums where the firmware/kernel devs etc are. I can't really advise further (It's a Raspbian/firmware issue).

timbellomo

copied bootcode.bin and start.elf from backup and it's booting again.

new dmesg:
http://pastebin.com/6vJKQkgw

i haven't updated the firmware/kernel via rpi-update.

BuZz

There is an issue with the firmware/kernel you are running I think - I cannot advise further and if updating stops it booting, perhaps there is something wrong with your usb booting set-up. I would report to raspberrypi.org and get some advice from there.

BuZz

Also see this - https://www.raspberrypi.org/forums/viewtopic.php?p=1028131#p1028131

Read from that post.

timbellomo

Thanks so much. Updating the firmware got me sorted. It's showing the proper amount of memory now... It's just not booting into emulationstation. Just drops to console... working on that now.

EDIT: It was the memory split. Reverted and now everything boots up again. Back to the beginning; installing emulationstation-kids.