Help needed for a Handheld Project

[Jiehfeng]

@moosepr My bad, I didn't know you were talking about programming it, but thank you for the tutorials, I'll be using those.

So how do I connect w/e to the Pi? Let's say a button for example, it has 4 metal pins. If I'm correct, you push it down on 4 holes on the PCB anywhere, and solder the bottom of it. From there where do I connect it to the raspberry pi? The wires soldered again from the bottom?
Are PCB's just basic boards you solder stuff onto or is there much more to it? I'm guessing all the holes aren't connected and separate like a breadboard? So it's basically a mounting board?

[moosepr]

@Jiehfeng the board you have is just a mounting board in essence, but you can link bits together to make circuits. You can make custom boards that link things, but that is getting more complicated

The buttons trend to have 4 pins, but normally they will be in pairs, so they will technically be linked together. You could test the behavior with a battery, led, and some wire to see which pins are linked all the time, and which link when you press the button

You normally connect one side of all the buttons to ground and the other side to the I/O pins of the teensy. Your program on the teensy will allow you to set which pin triggers which output

[Jiehfeng]

@moosepr Brilliant, thank you so much. So basically, in my handheld I'll be cutting squares from the PCB to mount buttons on them. Then connect all the ground pins with wires all going into one wire connected to the ground?
How do I connect the analog stick? In the OP I got a Wii U analog stick which already seems to have a PCB. It has 4 pins, I'm thinking it uses Red, Black, Yellow, and White wires, how do I connect those?

[moosepr]

@Jiehfeng your analog stick seems to have 5 pins. They normally work like variable resistors, which have 3 pins. One will be connected to +ve, one to -ve, and the this is connected somewhere in between. Your teensy will measure the voltage from the middle pin, which will change depending on it angle of the stick.

https://www.arduino.cc/en/Tutorial/AnalogInput

You will basically have 1 analog input for each stick direction.

[moosepr]

@Jiehfeng

[Jiehfeng]

@moosepr What is +ve or -ve? Or where is that?

So to put it in perspective, what colour wires do I wire exactly from the 5 pins to the Teensy LC? (kinda noob so don't understand yet)

[Jiehfeng]

@Jiehfeng That arduino tutorial has many different parts I don't have, so I don't really know how to understand it with my own parts.

[moosepr]

@Jiehfeng ah sorry, on the sticks, +ve is the pwr and -ve is the gnd. Connecting to the teensy you will want to connect the pwr pin on the stick to the 3.3v on the teensy, and gnd to gnd.

you will then want to connect the dir pins (dirH and dirV), into analog pins on the teensy (they are the a0-a9 pins). and for a final bonus, you could attach the click pin from the sticks into any of the digital pins (the grey ones on the diagram) you could always assign them to start/select so you dont need the extra buttons

your code on the teensy will then read the voltage from the analog pins, which will range from 0 to 3.3v over the range of movement of the stick

[Jiehfeng]

@moosepr Thanks a bunch, that's 90% of the info I need to finish my project. The other 10% is the wires. I understand completely where the pins connect to the teensy, but what colour wires for what pins?

GND - Black
PWR - Red
Dir H - Yellow?
Dir V - Green?
Click - White?

Do buttons use red or white wire?

[moosepr]

@Jiehfeng technically speaking, the colour of the wires is irrelevant. as long as you know what colour does what, your golden. Most people do tend to stick with red for power, and black for ground, but nothing is set in stone

[Jiehfeng]

Hey, I just got the Teensy LC with a few momentary push button switches. I put a button onto the PCB and soldered it on, then put a red wire to the top left pin and the black wire to the bottom left pin (soldered), and connected the black to the GND on the Teensy and the red to the 0 digital pin.
But for some reason my button isn't working? I tried the basic example and button example on teensyduino but the button won't respond.

[moosepr]

@Jiehfeng do you have access to a multimeter?

On the push buttons, there are normally 4 pins, but some are connected and some switch.

If you look at the bottom right part of the image, the top 2 pins are always connected together, and the bottom pins are connected together, then all 4 are connected together when the button is pressed

[Jiehfeng]

@moosepr No sadly not.
I'll try switching the wires up to every possible pin and see if it works. The switch is SPST btw.

[Jiehfeng]

@Jiehfeng Just tried with another button, works fine. I guess that button was faulty. Thanks again. :)