Another PiStation-project
-
Not that bad but to have less wiring i would of stripped out the controller/memory card ports and then bought 1 usb hub with 3 ports and then get 1 more usb hub with 2 ports stripped it out of the casing then i would have 4 for controllers and one for transferring files and also the area where you have the CD i would of cut open more of the area and since you will be powering it with the original power source could of done a little bit of wiring to have the fan connect there as well and use a fan a little bit bigger.
Finally just to have power air flow drill on the top cover 2 holes where the fan would be and on the right side i would of drilled about 10 smaller holes with applied a dust filter on the outer side because you know for any system it does collect dust in time especially when using a fan. -
So you mean that I should have stripped off the original ports and basically, destroyed the original looks of it ? I can always get a multitap, which will work, since this config works like the original system. And I have that hub inside, which can be accessed via CD lid to do servicing.
About the fan, I bought slightly bigger one and it's now hooked up straight to the PS1 PSU, into that 7.6V pin, so it runs in decent speed. The fan is also about 10mm off from the surface so it will get fresh air sucked in from the sides. And the case itself has breathing holes, so it's unnecessary to cut it open more. I have been testing the machine for many hours and it only gets mildly warm and it blows the air out from the left side vents.
My soul rests, when I hear the PS1 boot music
-
By adding in the back those hinges you already ruined the original look anyways and anyways by enabling that way if you have a friend that comes over with lets say an Xbox controller he would have to plug it in on the top because not everyone was a fan of the playstation controllers which come on that would look even more weird having a wire hanging out of the disc tray.
Also if you have your hands on a 3D printer or know someone that has one you could easily make the ports for the USB and besides that if you have arcade sticks as well wouldn't it still look weird with the wires coming out of the lid.
Also like i did mention as well for the fan it would lower the temp even more if you were to slap in something like a 60, 70 or even 80mm fan and also drilling some holes where your fan is position would allow air flow to work out better since you want air to come inside the system because if you look at a lot of people's builds as well when it comes down to using a fan they would drill some holes or even the small pie cases with a fan always has ventilation on the top as well.
It is still not that bad but would of had room for other things in the future for the system because there is hardly any room for anything you might want to add in.
Also one other thing i would of done to make it a little more cooler is instead of the hinges you could of cut out a small hole and used a micro sd card ribbon just so if you were to plan on replacing the SD card or if something was to happen to your SD card you would have to unscrew your Pi just to take it out since in the image it shows you have no way of taking it out without damaging the system. -
@dd-indeed as a pi station owner, i take your side on this. I have 1 usb port in the back. I would never want usb ports on the front. I like the front to look as stock as possible. If people dont like a ps1 or ps2 controller who cares. I like more authenticity so i only use sony ps 1, 2, 3 controllers on mine. Anything that says sony. And i am a bigger fan of 360 controllers.
-
Edit: Sorry, I didn't meant this to you
-
Damn, this forum would need some serious improvements haha, constantly having issues and connection cuts.
Anyway, like I said in my first message, bluetooth is for having other controllers, so I don't need to have USB-ports on the front. And the hinge is on the back, so no one can't see it anyway, so it doesn't spoil the looks. Also, even if the SD card is not removable without removing the whole raspi, it doesn't matter, as the SD unlikely will get corruped and if does, usually the kernel works, so you can fix stuff from the command console anyway. Last but not least, I can't fit in any bigger fans without destroying the whole case and spoiling the looks, since big fans are always too thick, 20mm, so there's simply no enough room for them in this case. And the raspi doesn't recuire big fans, it's not like a normal, regular PC.
-
Oh hey, you asked about some issues from some games, I managed to take this screenshot from Colin McRae Rally 2.0, where I encountered this strange issue, some of distances between graphical levels are incorrect:
Notice that second tree, that the car is in front of it, rather than behind where it should be.
-
@dd-indeed Are you using a PSX bios?
-
Yes, the regular one, SCPH1001, US-version.
-
That's okay - some glitches are relating from a missing bios
-
Yea I noticed that, some games freezed on intro, some refused to run and many of them had variety of issues. But at least the performance has been good overall in almost all games. And that NTSC format on USB stick, where the games are, helps with that freezing/loading issue I mentioned.
-
As you can see i stripped out the fans from an old PS3 cooling fan because the controller board for it was burnt out which is just as thick as the one you have in your Pi right now and people has done tests with bigger fans on their Pi's which lowers the system temp by roughly between 15°C and 20°C which has people shown before with a 20mm fan it mainly lowers it by 10°C so i for me i would prefer to have 15°C less on my Pi than 10°C less on my Pi and also for your game you should also try out a different PSX emulator and also try out SCPH-101 instead because the slim bios might work better than the fat bios.
-
Well, I already have 50 mm fan installed and that's enough for now. If I would install bigger fan to it, I would need to rethink the whole system and take a step back in functionality of it, so I'll let it be like it is right now. Even the 50 mm fan blows just enough of the air out, temps reach to around 60 C, which are still well within the limits.
But about that BIOS, that's a good tip, I'll try that out, thanks.
Edit: SCPH-101 bios fixed at least one glitch at the menu transition from car setup menu to the race beginning on CMR 2.0.
-
Always play around with each kind of bios for the system and also you could try PSX2PSP which turns the bin/cue/iso into a PBP file instead which does compress the game to be smaller and could help with making the game look better.
-
@ecks said in Another PiStation-project:
Always play around with each kind of bios for the system and also you could try PSX2PSP which turns the bin/cue/iso into a PBP file instead which does compress the game to be smaller and could help with making the game look better.
Well with current setup I have, I don't use any shaders for PS1 games, since they're not working as I would want to and slows down the games way too much. But, one thing that could help with the looks of the game is 3x resolution, which is apparrently not possible yet. The double resolution does wonders indeed, but triple resolution would look even better. Only things PS1 games would need is 2D filters for static stuff and 2-3x resolution for 3D rendered stuff to make them look great. That compression could help with the performance a bit, I'll examine that thing later on.
-
Okay, I've now finished the build as those shorter HDMI-cables arrived today. Attached them to the case with cable anchors:
But now, I'm needing help regarding the performance. I noticed, that GT2 slows down on certain places, so overclocking is definitely needed. Could someone help and write the proper instructions of how to do that ? I already searched information about it and wrote couple lines into the boot config, but it didn't work.
Also, I'm having issues with splashscreens. They start to play on the boot, but then suddenly cuts off after some seconds. I already wrote those couple lines, that should prevent it from happening, but it didn't help. So I would need help with them as well.
-
Update: I found one topic, where the overclocking guide was clear enough and worked straight away:
https://www.instructables.com/id/RetroPie-Overclocked-Raspberry-Pi-3-for-Video-Game/
-
Deleted
-
After couple months of playing, I started to notice, that my design is not good enough in terms of cooling. The machine runs really hot after multiple hours of playing and starts to smell a bit. I decided, that I need to upgrade the heatsinks and the fan as well. Propably those laptop radial fans would be the best solution in terms of space and they're pretty cheap as well. I'll update some information over here, once I've done those changes.
-
deleted
Contributions to the project are always appreciated, so if you would like to support us with a donation you can do so here.
Hosting provided by Mythic-Beasts. See the Hosting Information page for more information.