Cannonball Engine (Outrun Emulator)

edmaul69

@jretropie i turned on scanlines for the game myself. I think even that is an improvement.

humppa

I managed to get the Hires setting running smoothly by using the following (moderate) overclocking settings in /boot/config.txt:

arm_freq=1300
core_freq=500
sdram_freq=500
over_voltage=2

The framerate needs to be set to 30 fps though. With the framerate set to 60 fps the sound will still stutter. The Pi 3 manages to achieve ~50fps according to the optional fps-display.

Regarding the joypad "up and down issue" in the menus, I am also interested in a solution.
I have an XBOX 360 controller and I am using the left analogue joystick in "wheel mode" using the following setting:

<analog enabled="2">
	<!-- Select axis for analog controls 
         You can place the accelerator and the brake on the same axis if your controller
         has a split axis setup.
         
         For an XBox 360 Controller, the wheel should be axis 0 and the pedals on axis 2.
      -->
	<axis>
		<wheel>0</wheel>
		<accel>2</accel>
		<brake>2</brake>
	</axis>

Usually, this is set to "0", which means that the analogue stick of my joypad would work as a digital one. The "2" setting allows much better steering control in my view.
However, setting <analog enabled="2"> also means that the left joystick is deactivated for the menus. With a setting of "0", the analogue stick would kind of work, but sometimes I am e.g. unable to move down in the menus. So I am using my keyboard instead. I really need to find a way to configure the D-PAD up and down buttons for the game menu...

edmaul69

Having my pi overclocked when i set it to enhanced or hi res it either kicks me back out to emulationstation or it locks up in a matter of seconds after the race starts.

humppa

@edmaul69: What overclocking settings have you tried? In general, the overclocking potential varies a lot. Some have been running their systems stable at 1375Mhz, others are already experiencing instabilities at 1300Mhz.

edmaul69

@humppa i set it to your posted settings. Ive had it running at 1350mhz before this but i never found anything run any different so i removed my overclocking settings. Im going to try with an overvoltage of 4.

humppa

@edmaul69
Are you using a heatsink and/or fan? I have only been using heatsinks so far, but I have just ordered a new case with a hole for a fan. I am hoping that this will allow better OC-settings. Even with my conservative settings, I have seen that the CPU is throttling after a while because temperatures are going over 82°C.
Besides Cannonball, I think mainly Dreamcast and N64 emulation will profit from overclocking.

edmaul69

@humppa i have a heatsink. No other system has a problem with overclocking on my system. I went full blown overclocking settings (not just changing the 3 basic settings) and had it running at 1350mhz. Only problem was when you finished a race and it went to load the map showing your distance it boots me right back to emulationstation.

edmaul69

so i turned off widescreen and got it to not exit back to emulationstation. the sound still is not perfect. it suffers with too much graphics on the screen and at the intro. but leaving it sitting on the start line too long it kicks me back out everytime.

retrocraze

Hi Guys,

Sorry to bump this topic.

I am interested in running Cannonball on my retropie and I have all of the relevant files to do so. I am just unsure on how install this on my retropie.

The Zip files structure looks like this:

res (folder)
roms (folder)
cannonball.exe
config.xml
sdl.dll

The roms folder contains:

epr-10187.88
epr-10327a.76
epr-10328a.75
epr-10329a.58
epr-10330a.57
epr-10380b.133
epr-10381a.132
epr-10382b.118
epr-10383b.117
mpr-10371.9
mpr-10372.13
mpr-10373.10
mpr-10374.14
mpr-10375.11
mpr-10376.15
mpr-10377.12
mpr-10378.16
opr-10185.11
opr-10186.47
opr-10188.71
opr-10189.70
opr-10190.69
opr-10191.68
opr-10192.67
opr-10193.66
opr-10230.104
opr-10231.103
opr-10232.102
opr-10266.101
opr-10267.100
opr-10268.99

Do I copy the entire zip file to:

/home/pi/RetroPie/roms/ports/cannonball

???

Any help would be appreciated.

Chris

jonnykesh

@retrocraze Install through the RetroPie setup script. manage packages > optional > cannonball. This will then show up in the Ports section.
make sure the ROM you have is the Rev B version. This is not outrunb.zipIt is just named outrun.zip.
Unzip and place the individual files (31 of them) in the /home/pi/RetroPie/roms/ports/cannonball/ folder along side the roms.txt file. Open the roms.txt to ensure your files match those needed.
Restart Emulation Station. Play

ts-x

@humppa said in Cannonball Engine (Outrun Emulator):

I managed to get the Hires setting running smoothly by using the following (moderate) overclocking settings in /boot/config.txt:

arm_freq=1300
core_freq=500
sdram_freq=500
over_voltage=2

The framerate needs to be set to 30 fps though. With the framerate set to 60 fps the sound will still stutter. The Pi 3 manages to achieve ~50fps according to the optional fps-display.

Regarding the joypad "up and down issue" in the menus, I am also interested in a solution.
I have an XBOX 360 controller and I am using the left analogue joystick in "wheel mode" using the following setting:

<analog enabled="2">

  <axis>
  	<wheel>0</wheel>
  	<accel>2</accel>
  	<brake>2</brake>
  </axis>
Usually, this is set to "0", which means that the analogue stick of my joypad would work as a digital one. The "2" setting allows much better steering control in my view.
However, setting <analog enabled="2"> also means that the left joystick is deactivated for the menus. With a setting of "0", the analogue stick would kind of work, but sometimes I am e.g. unable to move down in the menus. So I am using my keyboard instead. I really need to find a way to configure the D-PAD up and down buttons for the game menu...

This solution corrected the drift problems I was experiencing with my Xbox360 controller as well. Has anyone since come up with a workaround to address the resulting joystick menu deactivation (aside from using a keyboard)?

luckyluca

@ts-x said in Cannonball Engine (Outrun Emulator):

@humppa said in Cannonball Engine (Outrun Emulator):
I managed to get the Hires setting running smoothly by using the following (moderate) overclocking settings in /boot/config.txt:

arm_freq=1300
core_freq=500
sdram_freq=500
over_voltage=2

The framerate needs to be set to 30 fps though. With the framerate set to 60 fps the sound will still stutter. The Pi 3 manages to achieve ~50fps according to the optional fps-display.

Regarding the joypad "up and down issue" in the menus, I am also interested in a solution.
I have an XBOX 360 controller and I am using the left analogue joystick in "wheel mode" using the following setting:
<analog enabled="2">
  
  <axis>
  	<wheel>0</wheel>
  	<accel>2</accel>
  	<brake>2</brake>
  </axis>
Usually, this is set to "0", which means that the analogue stick of my joypad would work as a digital one. The "2" setting allows much better steering control in my view.
However, setting <analog enabled="2"> also means that the left joystick is deactivated for the menus. With a setting of "0", the analogue stick would kind of work, but sometimes I am e.g. unable to move down in the menus. So I am using my keyboard instead. I really need to find a way to configure the D-PAD up and down buttons for the game menu...
This solution corrected the drift problems I was experiencing with my Xbox360 controller as well. Has anyone since come up with a workaround to address the resulting joystick menu deactivation (aside from using a keyboard)?

I'd be interested in a solution as well.
At the very least it would be great to map ESC to the joystick in order to quit the game without navigating the menu with analogue on.