Daphne . Arcade joystick orientation wrong.

pjft

@dabbler sudo git checkout retropie

Actually, just re-merged it there. Try again, but make sure it's retropie, not daphne as you had mentioned.

dabbler

@pjft said in Daphne . Arcade joystick orientation wrong.:

@dabbler sudo git checkout retropie

Actually, just re-merged it there. Try again, but make sure it's retropie, not daphne as you had mentioned.

No luck im afraid, i get :

pi@retropie:~/RetroPie-Setup $ sudo git checkout retropie
error: pathspec 'retropie' did not match any file(s) known to git

full steps:

cd /home/pi/RetroPie-Setup/
sudo ./retropie_packages.sh daphne clean
sudo git clone https://github.com/pjft/daphne-emu/ tmp/build/daphne
sudo git checkout retropie
sudo ./retropie_packages.sh daphne depends
sudo ./retropie_packages.sh daphne build
sudo ./retropie_packages.sh daphne install
sudo ./retropie_packages.sh daphne configure

pjft

@dabbler You're missing navigating to the daphne folder, as I mentioned, after cloning the repository.

sudo git clone https://github.com/pjft/daphne-emu/ tmp/build/daphne
cd tmp/build/daphne
sudo git checkout retropie
cd /home/pi/RetroPie-Setup/

dabbler

@pjft said in Daphne . Arcade joystick orientation wrong.:

sudo git clone https://github.com/pjft/daphne-emu/ tmp/build/daphne
cd tmp/build/daphne
sudo git checkout retropie
cd /home/pi/RetroPie-Setup/

Works a treat. Joystick fully working and Bega etc working - thanks so much @pjft

For others, the full steps to install and build this version are:

cd /home/pi/RetroPie-Setup/
sudo ./retropie_packages.sh daphne clean
sudo git clone https://github.com/pjft/daphne-emu/ tmp/build/daphne
cd tmp/build/daphne
sudo git checkout retropie
cd /home/pi/RetroPie-Setup
sudo ./retropie_packages.sh daphne build
sudo ./retropie_packages.sh daphne install
sudo ./retropie_packages.sh daphne configure

phnman

@dabbler

With the updated space on the first line everything works great. Thanks to pjft for compiling

tafaz73

@pjft
Finally someone upped again this thread. I'm still stuck with non orking joystick. Unfortunately, when I'm building Daphne I receive following error

g++: error: vldp2/libmpeg2/cpu_accel.o: No such file or directory
g++: error: vldp2/libmpeg2/alloc.o: No such file or directory
g++: error: vldp2/libmpeg2/cpu_state.o: No such file or directory
g++: error: vldp2/libmpeg2/decode.o: No such file or directory
g++: error: vldp2/libmpeg2/header.o: No such file or directory
g++: error: vldp2/libmpeg2/motion_comp.o: No such file or directory
g++: error: vldp2/libmpeg2/idct.o: No such file or directory
g++: error: vldp2/libmpeg2/idct_mmx.o: No such file or directory
g++: error: vldp2/libmpeg2/motion_comp_mmx.o: No such file or directory
g++: error: vldp2/libmpeg2/slice.o: No such file or directory
g++: error: vldp2/libvo/video_out.o: No such file or directory
g++: error: vldp2/libvo/video_out_null.o: No such file or directory
make: *** [Makefile:67: all] Error 1
/home/pi/RetroPie-Setup

Any ideas?

pjft

@tafaz73 No ideas.

Are you following these instructions?

https://retropie.org.uk/forum/topic/16464/daphne-arcade-joystick-orientation-wrong/115?_=1611934569118

Have you updated the RetroPie-Setup script?

tafaz73

@pjft
Yes, this is what I have done.
The issue happened at the end of

sudo ./retropie_packages.sh daphne build

No, I didn't update Retropie-Setup script. I will do and then test the build again.

Thank you

Pennywisekrueger

I like others have just found this thread seconds before tearing my last strands of hair out.

For the complete raspberry pi noob like me - what do I do?

Connect to wifi / lan
Boot to command line and
Type the commands in exactly as shown below;

cd /home/pi/RetroPie-Setup/
sudo ./retropie_packages.sh daphne clean
sudo git clone https://github.com/pjft/daphne-emu/ tmp/build/daphne
cd tmp/build/daphne
sudo git checkout retropie
cd /home/pi/RetroPie-Setup
sudo ./retropie_packages.sh daphne build
sudo ./retropie_packages.sh daphne install
sudo ./retropie_packages.sh daphne configure

After this do you need to amend the daphne config file still?

Thanks for your help (anyone who sees this) 😣

pjft

@pennywisekrueger Good question about step 4, I don't have an answer as I had already set up my buttons - this just adds the joystick support.

I imagine you might have to edit the file, as your button configuration will be different to others' (at least fine-tuning) but worth launching Daphne before changing the file and seeing how it goes.

Pennywisekrueger

@pjft but I got the rest right!!? 🙏🏼

pjft

@pennywisekrueger As far as I remember, yes.

Pennywisekrueger

This post is deleted!

Pennywisekrueger

@pjft I’m getting stuck at this line

sudo git clone https://github.com/pjft/daphne-emu/ tmp/build/daphne

Should this be one line or two?

pjft

@pennywisekrueger one, but you haven't given me any error message or even what RetroPie version you're running and on what pi, etc.

Please share more details about what you're running to.

Pennywisekrueger

@pjft sorry - I’m on a pi 3b+

I’ve now got to the line

sudo./retropie_packages.sh daphne build

And it says no such file or directory

pjft

@pennywisekrueger There's a space between sudo and ".". Are you on /home/pi/RetroPie-Setup ?

Pennywisekrueger

@pjft I am now! My initial post missed some vital parts !! I’m there now everything seems to have worked - how do I boot back into emulation station to see if it’s worked 😬😬

Current command line flashing says

Pi@retropie:~/RetroPie-setup $

pjft

@pennywisekrueger sudo reboot now will restart the machine

Pennywisekrueger

@pjft it works!!!!!!!! THANK YOU SOOOOOOO MUCH!!!!

Dragons Lair 2 tested 👌🏼👌🏼👌🏼

Any idea why it uses player 2 controls (not that I’m that bothered)