Development of module-script generator for lr-mess, lr-mame and mame standalone

JimmyFromTheBay · 9 Jun 2021, 22:42

@folly I have very little idea what I'm doing here, but this is what happens if I try to install coco3 from the script.

hhtien1408 · 10 Jun 2021, 02:09

@DTEAM @dmmarti @Folly @valerino
Great news for Super Acan Funtech
The lastest official MAME 0.233 can emulate sound already.
Check the youtube video

Folly · 6 Oct 2021, 07:39

@hhtien1408

That looks/sounds really good !

Folly · 6 Oct 2021, 07:40

@jimmyfromthebay said in Development of module-script generator for lr-mess and mame standalone:

@folly I have very little idea what I'm doing here, but this is what happens if I try to install coco3 from the script.

It looks like you have a corrupted module-script inside your RetroPie-Setup.

Did you see it at the end of the install of coco3 ?

Do you also see this when starting the RetroPie-Setup ?

Can you see in the experimental packackages if coco3 is installed ?

JimmyFromTheBay · 6 Oct 2021, 10:12

@folly said in Development of module-script generator for lr-mess and mame standalone:

@jimmyfromthebay said in Development of module-script generator for lr-mess and mame standalone:

@folly I have very little idea what I'm doing here, but this is what happens if I try to install coco3 from the script.

It looks like you have a corrupted module-script inside your RetroPie-Setup.

That was weird - I'd literally just formatted an SD card, installed Retropie on it and run nothing but your script. But I updated RetroPie-Setup and all the Coco stuff is installed now :)

Sadly it now crashes on the "Initialising" screen. Should I have the BIOS files (I've got all these CoCo ones from the 0.232 set) somewhere other than in pi>RetroPIe>BIOS?

Do they need to be in a special folder or something? This is the runcommand.log:

Parameters: 
Executing: /opt/retropie/emulators/mame/mame -v -c -ui_active coco3 -flop1 "/home/pi/RetroPie/roms/coco3/Pac-Man (emulated).DSK"
Attempting load of mame.ini
Parsing mame.ini
Attempting load of mame.ini
Parsing mame.ini
Attempting load of horizont.ini
Attempting load of computer.ini
Attempting load of raster.ini
Attempting load of source/coco3.ini
Attempting load of coco.ini
Attempting load of coco3.ini
Reading translation file English: 1 strings, original table at word offset 7, translated table at word offset 9
Loaded 0 translations from file English
Starting plugin data...
Starting plugin hiscore...
Attempting load of mame.ini
Parsing mame.ini
Attempting load of mame.ini
Parsing mame.ini
Attempting load of horizont.ini
Attempting load of computer.ini
Attempting load of raster.ini
Attempting load of source/coco3.ini
Attempting load of coco.ini
Attempting load of coco3.ini
Available videodrivers: x11 KMSDRM RPI dummy 
Current Videodriver: KMSDRM
	Display #0
		Renderdrivers:
			    opengl (0x0)
			 opengles2 (0x0)
			  opengles (0x0)
			  software (0x0)
Available audio drivers: 
	alsa                
	sndio               
	dsp                 
	disk                
	dummy               
Build version:      0.232 (mame0232)
Build architecure:  
Build defines 1:    SDLMAME_UNIX=1 SDLMAME_X11=1 SDLMAME_LINUX=1 
Build defines 1:    LSB_FIRST=1 
SDL/OpenGL defines: SDL_COMPILEDVERSION=2009 USE_OPENGL=1 
Compiler defines A: __GNUC__=8 __GNUC_MINOR__=3 __GNUC_PATCHLEVEL__=0 __VERSION__="8.3.0" 
Compiler defines B: __unix__=1 
Compiler defines C: __USE_FORTIFY_LEVEL=0 
Enter init_monitors
Adding monitor screen0 (1920 x 1080)
Leave init_monitors
Enter sdlwindow_init
Using SDL native texturing driver (SDL 2.0+)
Loaded opengl shared library: <default>

Hints:
	SDL_FRAMEBUFFER_ACCELERATION             (NULL)
	SDL_RENDER_DRIVER                        (NULL)
	SDL_RENDER_OPENGL_SHADERS                (NULL)
	SDL_RENDER_SCALE_QUALITY                 (NULL)
	SDL_RENDER_VSYNC                         (NULL)
	SDL_VIDEO_X11_XVIDMODE                   (NULL)
	SDL_VIDEO_X11_XINERAMA                   (NULL)
	SDL_VIDEO_X11_XRANDR                     (NULL)
	SDL_GRAB_KEYBOARD                        (NULL)
	SDL_VIDEO_MINIMIZE_ON_FOCUS_LOSS         (NULL)
	SDL_IOS_IDLE_TIMER_DISABLED              (NULL)
	SDL_IOS_ORIENTATIONS                     (NULL)
	SDL_XINPUT_ENABLED                       (NULL)
	SDL_GAMECONTROLLERCONFIG                 (NULL)
	SDL_JOYSTICK_ALLOW_BACKGROUND_EVENTS     (NULL)
	SDL_ALLOW_TOPMOST                        (NULL)
	SDL_TIMER_RESOLUTION                     (NULL)
	SDL_RENDER_DIRECT3D_THREADSAFE           (NULL)
	SDL_VIDEO_ALLOW_SCREENSAVER              (NULL)
	SDL_ACCELEROMETER_AS_JOYSTICK            (NULL)
	SDL_MAC_CTRL_CLICK_EMULATE_RIGHT_CLICK   (NULL)
	SDL_VIDEO_WIN_D3DCOMPILER                (NULL)
	SDL_VIDEO_WINDOW_SHARE_PIXEL_FORMAT      (NULL)
	SDL_VIDEO_MAC_FULLSCREEN_SPACES          (NULL)
	SDL_MOUSE_RELATIVE_MODE_WARP             (NULL)
	SDL_RENDER_DIRECT3D11_DEBUG              (NULL)
	SDL_VIDEO_HIGHDPI_DISABLED               (NULL)
	SDL_WINRT_PRIVACY_POLICY_URL             (NULL)
	SDL_WINRT_PRIVACY_POLICY_LABEL           (NULL)
	SDL_WINRT_HANDLE_BACK_BUTTON             (NULL)
Leave sdlwindow_init
Enter sdl_info::create
Leave renderer_sdl2::create
window: using renderer opengl
renderer: flag SDL_RENDERER_ACCELERATED
renderer: flag SDL_RENDERER_TARGETTEXTURE
Audio: Start initialization
Audio: Driver is alsa
Audio: frequency: 44100, channels: 2, samples: 512
sdl_create_buffers: creating stream buffer of 22528 bytes
Audio: End initialization
Keyboard: Start initialization
Input: Adding keyboard #0: System keyboard (device id: System keyboard)
Keyboard: Registered System keyboard
Keyboard: End initialization
Mouse: Start initialization
Input: Adding mouse #0: System mouse (device id: System mouse)
Mouse: Registered System mouse
Mouse: End initialization
Joystick: Start initialization
Input: Adding joystick #0: USBGamepad (device id: 03000000790000001100000010010000)
Joystick: USB Gamepad  [GUID 03000000790000001100000010010000]
Joystick:   ...  2 axes, 10 buttons 0 hats 0 balls
Joystick:   ...  Physical id 0 mapped to logical id 1
Joystick:   ...  Does not have haptic capability
Input: Adding joystick #1: USBGamepad (device id: 03000000790000001100000010010000)
Joystick: USB Gamepad  [GUID 03000000790000001100000010010000]
Joystick:   ...  2 axes, 10 buttons 0 hats 0 balls
Joystick:   ...  Physical id 1 mapped to logical id 2
Joystick:   ...  Does not have haptic capability
Joystick: End initialization
Searching font Liberation Sans in -. path/s
font Liberation Sans|Regular is not TrueType or BDF, using MAME default
Input: Autoenabling mouse due to presence of a mouse
Input: Autoenabling mouse due to presence of a mouse
Input: Autoenabling mouse due to presence of a mouse
Input: Autoenabling mouse due to presence of a mouse
coco3.rom NOT FOUND (tried in coco3 coco)
disk11.rom NOT FOUND (tried in coco_fdc_v11 coco3 coco)
Fatal error: Required files are missing, the machine cannot be run.
sdl_kill: closing audio
Enter sdlwindow_exit
Leave sdlwindow_exit

But coco3.rom and disk11.rom are in pi>RetroPie/BIOS/coco3.zip, so I can only assume coco3.zip should be somewhere else.

Folly · 6 Oct 2021, 19:04

@jimmyfromthebay

You have to put the bios files in : ~/RetroPie/BIOS/mame/coco3.zip

Really no idea what you did and what's wrong.

Can't really tell, but perhaps you have a broken SD that has gone read-only.
You can see that if you put files on it and later after a reboot they are gone again.
Or delete a file and after a reboot they are back again.
Then it's time to buy a new SD card.

From my own experience, SD cards don't have a long lifetime,
I am now using a good old fashioned hard-drive on my pi4.
Faster over USB3.0 and far more reliable and lives much longer !

JimmyFromTheBay · 10 Jun 2021, 17:14

@folly Ah, the problem was that I didn't have them in the MAME folder. Cheers, will sort that out :)

Thanks for your patience, and for this awesome script.

JimmyFromTheBay · 10 Jun 2021, 17:36

@folly said in Development of module-script generator for lr-mess and mame standalone:

I can play the game using the numpad keys ! (0 = coin and jump, 2=down,8=up,4=left,6=right)
For lr-mess there is a hotkey issue, so have to test later.

I just got it working absolutely fine in lr-mess, and smoother than with MAME. Joystick control works, but you have to go into Analog Controls and set all the sensitivity readings to 100 and the auto-centre settings to 255, because it's expecting analogue input so it takes Mario ages to reverse unless you basically turn the analogue controls digital.

Folly · 10 Jun 2021, 18:02

@jimmyfromthebay said in Development of module-script generator for lr-mess and mame standalone:

@folly said in Development of module-script generator for lr-mess and mame standalone:

I can play the game using the numpad keys ! (0 = coin and jump, 2=down,8=up,4=left,6=right)
For lr-mess there is a hotkey issue, so have to test later.

I just got it working absolutely fine in lr-mess, and smoother than with MAME. Joystick control works, but you have to go into Analog Controls and set all the sensitivity readings to 100 and the auto-centre settings to 255, because it's expecting analogue input so it takes Mario ages to reverse unless you basically turn the analogue controls digital.

Haha, that's nice.

You beat me with your knowledge 👍.

JimmyFromTheBay · 10 Jun 2021, 18:27

@folly said in Development of module-script generator for lr-mess and mame standalone:

@jimmyfromthebay said in Development of module-script generator for lr-mess and mame standalone:

@folly said in Development of module-script generator for lr-mess and mame standalone:

I can play the game using the numpad keys ! (0 = coin and jump, 2=down,8=up,4=left,6=right)
For lr-mess there is a hotkey issue, so have to test later.

I just got it working absolutely fine in lr-mess, and smoother than with MAME. Joystick control works, but you have to go into Analog Controls and set all the sensitivity readings to 100 and the auto-centre settings to 255, because it's expecting analogue input so it takes Mario ages to reverse unless you basically turn the analogue controls digital.

Haha, that's nice.

You beat me with your knowledge 👍.

Well, it's nice to be able to give SOMETHING back :D

Folly · 6 Oct 2021, 19:55

@jimmyfromthebay

Thanks.

Just tested it with the joystick.

Works perfect with lr-mess !

JimmyFromTheBay · 10 Jun 2021, 20:51

@folly Don't forget to set the colour mode to CMP for the proper arcade look ;)

Folly · 11 Jun 2021, 06:20

@jimmyfromthebay

Thanks.

Yes indeed, I saw the composite mode.
Will use it.

Folly · 12 Jun 2021, 08:04

@valerino

Do you have some time to check out the front-end script ?
I would like to know what your experience is.

JimmyFromTheBay · 6 Dec 2021, 14:43

@folly I'm currently having a problem installing systems starting with certain letters from the script. For example if I try to install anything starting with Z (eg the ZX80) I get dumped to an error screen saying something about expecting five menu options and only finding four (or possibly the other way round), which I can only get out of by powering down and rebooting. (P and T seem to have this problem too.)

I'm also still having trouble making Dragon 32 games work (they load and start, but don't run properly), but this can be got around by using the CoCo 2 versions instead. However, for some reason the CoCo 2 emulation has a very washed-out palette and I can't find any setting in either Retroarch or the MESS menu that would fix it. CoCo 3 looks fine. Any idea what's going on there?

JimmyFromTheBay · 12 Jun 2021, 12:27

@jimmyfromthebay said in Development of module-script generator for lr-mess and mame standalone:

I'm also still having trouble making Dragon 32 games work (they load and start, but don't run properly), but this can be got around by using the CoCo 2 versions instead. However, for some reason the CoCo 2 emulation has a very washed-out palette and I can't find any setting in either Retroarch or the MESS menu that would fix it. CoCo 3 looks fine. Any idea what's going on there?

BREAKING: turns out the best plan is to simply run the CoCo 2 versions, which in almost all cases are basically identical to the Dragon 32 ones, through the Coco 3 emulator. So far everything works and you get the nice clean non-washed-out palette :)

JimmyFromTheBay · 12 Jun 2021, 13:43

@jimmyfromthebay said in Development of module-script generator for lr-mess and mame standalone:

@folly I'm currently having a problem installing systems starting with certain letters from the script. For example if I try to install anything starting with Z (eg the ZX80) I get dumped to an error screen saying something about expecting five menu options and only finding four (or possibly the other way round), which I can only get out of by powering down and rebooting. (P and T seem to have this problem too.)

Slightly more helpfully :D

Folly · 6 Dec 2021, 16:37

@jimmyfromthebay

Thank you for placing the issue.

I have seen that once before while developing the front -end.
I work with "comma seperate values" in the menu.
The whole menu of the systems is extracted from mame and then turned into "CSV-style" and injected into the menu.
If spitting isn't correct due to some characters in the names then you can get these problems.

I will have a look at it, once I can.

Edit :
I can't reproduce the problem over here using zx80 from all the possible menu options.
So, at the moment I can't really tell what's wrong.
I will have look at it later.

JimmyFromTheBay · 6 Dec 2021, 16:44

@folly I'm trying to install from option 11 (Alphabetical by systems). I've updated RetroPie-Script and re-downloaded add-mamedev-systems-test6.sh, but it's the same for all letters now as far as I can see. Options 8 and 10 work fine, btw.

Folly · 6 Dec 2021, 17:48

@jimmyfromthebay said in Development of module-script generator for lr-mess and mame standalone:

@folly I'm trying to install from option 11 (Alphabetical by systems). I've updated RetroPie-Script and re-downloaded add-mamedev-systems-test6.sh, but it's the same for all letters now as far as I can see. Options 8 and 10 work fine, btw.

When entering Option 11 (Picture 1):

can you see picture 2 after entering from picture 1 ?
can you see picture 3 after entering from picture 2 after selecting Z ?

Picture 1:

Picture 2:

Picture 3: