Pi in a Dreamcast VMU Build - WIP

moosepr

@obsidianspider thats the easy bit

raspi-config - enable spi

sudo nano /etc/modules - add in

spi-bcm2835
fbtft_device

sudo nano /etc/modprobe.d/fbtft.conf - add in

options fbtft_device name=fb_ili9163 gpios=reset:25,dc:24 speed=40000000 bgr=1 rotate=0 custom=1 fps=60

reboot

obsidianspider

@moosepr I'm workin on it! I'm workin on it!

obsidianspider

So, it works, kind of. Both screens are showing garbage data on the pixels on the right, one is showing them on the bottom as well. I haven't tried adjusting resolution yet, but the screen is mirroring what's going to HDMI correctly, aside from the garbage pixels.

I do have overscan disabled in /boot/config.txt

lilbud

@obsidianspider do the dead pixels show up under the VMU bezel?

moosepr

@obsidianspider hmmm are those the 128x128 screens, or the 128x160?

obsidianspider

@moosepr they're the "red board" screens.

Setting the HDMI resolution to 128 x 128 in /boot/config.txt didn't help.

Great refresh rate though. Very smooth.

@lilbud The whole screen shows. I'm going to actually end up coloring in the white surround black to hide it a bit. This is just "set in" but you get the idea.

moosepr

@obsidianspider just for shits and giggles, try running it with the other driver

options fbtft_device name=fb_st7735r gpios=reset:25,dc:24 speed=40000000 bgr=1 rotate=0 custom=1 fps=60

then if that works, try adding some size in there

options fbtft_device name=fb_st7735r gpios=reset:25,dc:24 speed=40000000 height=128 bgr=1 rotate=0 custom=1 fps=60

all in sudo nano /etc/modprobe.d/fbtft.conf of course

obsidianspider

@moosepr That gave me a different kind of garbage. The bad pixels moved to the other side, things are upside down, and the bottom output is garbled.

moosepr

@obsidianspider odd!! it behaves differently to the one i have got. Although mine is probably wired differently (you may also have a totally different screen on the board)

notro did point me in the direction of using the flex driver, where you can basically set the full init commands. I did start looking, but decided to wait till my boards arrived (they have literally just been marked as shipped!!)

here is all i know so far https://github.com/notro/fbtft/issues/453

moosepr

@obsidianspider Mine have H144TC215A-V0 on the ribbon

obsidianspider

I went back to the ILI9163 driver and then tried messing with some overscan settings, which didn't seem to help once EmulationStation loaded, but I do see that the garbled text appears to be from the console, so that may be an insight into what's going on.

I'm going to have to mess with it. Like I said, I want to make this stuff works before I go removing things from the board. ;)

obsidianspider

@moosepr Mine say TXDT144CF-47 on the ribbon

moosepr

@obsidianspider yours seems to have a few more pins than mine internally i think (although the search is a bit of a minefield)

i think the garbage is generally just leftovers from stuff that has been on the screen on other boots. from a cold boot it will be rainbowsnow, from a setings change and a reboot it will be whatever was there last time

obsidianspider

@moosepr I can confirm the rainbow snow from a cold boot. I can also confirm that the other screen behaves the same way. Initially it only had garbage on the right, but now it has garbage on the bottom and right, so it's consistent. I need to shift things down and to the right. Weird.

obsidianspider

@moosepr Ideally I'd like to be able to set overscan like on the 3.2" TFT I'm using so I can keep the image from displaying at the top of the screen where it's covered by the VMU plastic. Though, in looking through it, I have that one set up differently.

@obsidianspider said in Pi in a Gameboy Advance Build - WIP:

My SainSmart 3.2" TFT showed up today and getting it to work wasn't as straightforward as I initially read, but it was totally doable and the speed seems very good when connected to my test mule Raspberry Pi 2 with a fresh image of RetroPie updated to 4.0.6.

(I still have the protective film in place)

OK, so here's how I got the screen working on a freshly installed image of RetroPie 4.0.6 on a Raspberry Pi 2. Steps are a combination of a few posts here and on GitHub

First I added the following to the bottom of the /boot/config.txt
#Waveshare 3.2 TFT Screen
#same resolution for hdmi and tft
hdmi_force_hotplug=1
hdmi_cvt=320 240 60 1 0 0 0
hdmi_group=2
hdmi_mode=1
hdmi_mode=87

dtparam=spi=on
dtoverlay=waveshare32b:rotate=270,speed=82000000,fps=60
Then I rebooted and wondered why nothing had happened. It turned out I needed to install the device tree overlay (that's what dtoverlay means, you learn something every day). Since RetroPie is
git clone https://github.com/swkim01/waveshare-dtoverlays.git
sudo cp waveshare-dtoverlays/waveshare32b-overlay.dtb /boot/overlays/waveshare32b.dtbo

moosepr

@obsidianspider yeah I think the overscan basically just shrinks the image within the screen area, so we need to remove the rainbowsnow before the overscan can be used properly.

I think the init sequence needs tweaks to get the image starting in the correct place. I was going to start off using the link notro sent to me, and compare that against the init sequence within the driver code itself. Then once that was working, get the data sheet and see which registers can be tweaked

obsidianspider

@moosepr That makes a lot of sense. I need to run some errands, but I'll see what I can figure out tonight, if anything. Thanks again for assisting with this.

moosepr

@obsidianspider Not a problem! I need to fix it too! :p

obsidianspider

I realized that when I was playing with things, I put the following in the /boot/config.txt to get the 128x128 working at the right resolution. I'm not sure if this is better or worse for the garbage pixel problem (probably not affecting it)

hdmi_force_hotplug=1
hdmi_cvt=128 128 60 1 0 0 0
hdmi_group=2
hdmi_mode=1
hdmi_mode=87

I basically just took what I did for the Waveshare screen and adjusted it. Games are playing in the correct aspect ratio (I actually have a black bar at the top and bottom when playing a game), but EmulationStation DGAF and just takes up the whole screen.

To try to help with identification and troubleshooting, I pried one of the screens away from the board.

obsidianspider

Since this screen stuff appears to be a driver/software issue, I'm thinking about removing the screen from the board, making sure it works as well as it did when on the board, then fitting it to a VMU so I can try fitting a Zero in with it. The software stuff can be tweaked really any time. What say you, hive mind?