Pi in a Super Famicom Build

obsidianspider

@Danorak1981 I really don't know. It was $9 from eBay, so I'm sure it's not designed to be as resilient as a screen from an iPhone. I guess I'll find out over time. Stuff like that is part of why I made it removable. If it dies I can just unscrew it from inside the case and put in a new one with all of 9 soldered connections. Of course, that assumes they would still make a board of the same size if and when it dies.

Morph-X

Massive props to this build. The idea of popping in a display in the cartridge is only rivaled by your execution of it. Absolutely brilliant. It kind of transcends the "homebrew" category, it could well enough be a fully marketed product.

I hope it brings you just as much joy in using it as it did while building it.

Congratulations on a superb build!

obsidianspider

In a case of "while I'm at it", when I got my TFT working again after the new 20170303 kernel update was released I decided to do something about the images being displayed on the TFT.

When I was first getting things going I just resized the image to 320x240 and displayed it. It worked, but if the image wasn't the correct aspect ratio, the script didn't care and it resulted in a distorted image. Today I managed to correct that. My new (still admittedly hacky) script will now resize images proportionally so they fit inside the window without stretching.

I think it's a "more right" way to address the issue, and is a whole lot more convenient than making custom images for every single game so it doesn't look stretched.

obsidianspider

Today I added a 256GB USB drive to the Super Famicom Pi and it was pretty easy. The drive was a bit too long, but I learned from putting one in my Genesis hub Pi that by taking the case off it should fit with no problems. The blue LED is really bright, so I covered it with a piece of tape, because without it there was blue light bleeding out of all of the vent holes like a spaceship read to take off.

backstander

@obsidianspider
Monoprice is the place to get cables lol
I'm sure some people would like the blue-light-bleeding-out-of-all-of-the-vent-holes-like-a-spaceship-ready-to-take-off disease!

obsidianspider

@backstander Monoprice was the only vendor I could find with a short HDMI cable that also had small connectors. Everyone else had really thick rubber on the plug and the cable insulation was huge.

obsidianspider

Today I decided to work on moving my scripts to my USB drive for stability, and to clean things up since I was initially just cobbling things together to get them to work. One challenge I faced was that the USB drive isn't immediately mounted when the system boots. It takes a few seconds. To get around that I put the tftstart.sh script in the /home/pi/ folder and added a bit to tell it to wait until the USB folder is available before trying to execute the scripts that are located on it.

#!/bin/bash
# Wait for USB disk detection
# Disk drive mount we're waiting on
usbdrive="/media/usb0/retropie-mount"
# Max time to wait (in seconds)
maxwait=60
for (( i = 0; i <= $maxwait; i++ ))
do
  [ -d $usbdrive ] && break
  sleep 1
done

#load image
sudo python /home/pi/RetroPie/tft/imageparam.py "/home/pi/RetroPie/tft/images/RetroPie Splashscreen Blue.jpg"

#turn on backlight and enable Reset button toggle
sudo python /home/pi/RetroPie/tft/switch.py

I also updated my runcommand-onstart.sh script to reference images located in the ROMs folder (I'm moving images to the ROMs folder) and to also handle file names with square braces[ ], which were breaking the script.

# /opt/retropie/configs/all/runcommand-onstart.sh

# get the full path filename of the ROM
rom=$3

# get the system name
system=$1

# get rom filename without folder
rom_bn=$(basename "$rom")

#get rom filename without extension
rom_bn="${rom_bn%.*}"

# escape square brackets in rom filename
rom_bn="${rom_bn//\[/\\[}"
rom_bn="${rom_bn//\]/\\]}"

# Set a TFT-specific image if there is one
img="$(find "/home/pi/RetroPie/tft/images/roms/${system}" -type f -name "${rom_bn}-image.*" -print -quit)"

# If a TFT-specific image was not found, look in the images folder in the ROMs directory for that system
if [[ -z "${img}" ]];
then
   img="$(find "/home/pi/RetroPie/roms/${system}/images" -type f -name "${rom_bn}-image.*" -print -quit)"
fi

# If an image was not found in the ROMs directory for that system, check to see if there are any in the default emulationstation location
if [[ -z "${img}" ]];
then
   img="$(find "/opt/retropie/configs/all/emulationstation/downloaded_images/${system}" -type f -name "${rom_bn}-image.*" -print -quit)"
fi	

# If no game images are found, display one for the system being emulated
if [[ -z "${img}" ]];
then
   img="$(find "/home/pi/RetroPie/tft/images/systems" -type f -name "${system}.*" -print -quit)"
fi

# If no system image is found, default back to the Raspberry Pi logo
if [[ -z "${img}" ]];
then
   img="/home/pi/RetroPie/tft/images/Raspberry_Pi_Logo.svg.png"
fi

# run the python script to display the image
sudo python /home/pi/RetroPie/tft/imageparam2.py "$img"

I'm sure there is a lot that could still be improved or optimized, but things are working well.

Cybermen

@obsidianspider Very good work. I am also rebuilding and have a question. How did you connect the original reset button? On the bottom are 4 connection possibilities?

obsidianspider

@cybermen the reset button is discussed in this post earlier in this same thread. That said, there are multiple motherboard variants, so use your meter to test.

Cybermen

Super, Thank You.

obsidianspider

Update

I learned the hard way not to use rpi-update

It apparently updated you to the bleeding edge firmware, and not only did the update fail halfway through, but once it completed successfully, Linux kept crashing. Now to see if I can fix this mess. Fun?

obsidianspider

Well that was less than fun. Lesson learned, kids. If you have a heavily customized install, make sure you create an image of your SD card in case you blow it up like I did.

Also, take better notes. ;)

Things are working now, but it was a lot of head scratching to get all of my scripts in the right places.

Darksavior

@obsidianspider I updated to the latest stretch build and that didn't go well. The gamecon driver wouldn't build. I reverted to stable stretch and fixed some dependencies to get ES to compile. I made a backup just in case, but it looks like I won't need to use it.

obsidianspider

@darksavior I haven't tried Stretch. I heard it wasn't supported yet.

Darksavior

@obsidianspider Try at your own risk, but once I sorted my dependencies, ES and the emulators I use work fine https://retropie.org.uk/forum/topic/16145/retropie-upgrading-raspbian-jessie-to-stretch

BillyH

@obsidianspider it's probably in the thread here somewhere but I can't seem to find it: have you linked the original power switch to a system shutdown, and if so, how?

Now that I have a Pi, I'm thinking about either murdering my old SNES or finding one to murder, and using it as a case for the Pi. If/When I do so, I may look closer to threads like these for inspiration.

obsidianspider

@billyh Please don't break a known working SNES just for a Pi project. There are millions of ones that are inoperable.

I used a Mausberry tied to the stock SNES power switch.