SNES mini theme

mitu

@ash786i The same way you'd add any theme - go into the RetroPie system in Emulationstation, then open the ES Themes menu and select the theme you want to install to add it to your installed themes.

Paisano87

Hello, I am having problems when loading the theme, do not load the interface graphics, it stays blank and you only see the names of the systems in plain text, the carbon theme loads correctly, if I have verified that inside of each category is the distribution of the cover and text applied, but nothing more, white backgrounds and no sounds.
I did not find anything about it, I hope you can help me. Thank you

mitu

@Paisano87 Can you add more info about your system - https://retropie.org.uk/forum/topic/3/read-this-first ?

Paisano87

Thank you for answering mitu
I have a Raspberry Pî 3 B and RetroPie 4.4.9 version
Thanks

quicksilver

@Paisano87 What do you have your gpu/cpu memory split set to?

Paisano87

@quicksilver said in SNES mini theme:

What do you have your gpu/cpu memory split set to?

Sorry, I do not understand what you are asking me

mitu

@Paisano87 Check the /boot/config.txt file on your sd card, or insert the SD card into your PC and open the config.txt file you find in there. Post the output of that file in the forum.

Paisano87

@mitu said in SNES mini theme:

/boot/config.txt

For more options and information see

http://www.raspberrypi.org/documentation/configuration/config-txt.md

Some settings may impact device functionality. See link above for details

uncomment if you get no picture on HDMI for a default "safe" mode

#hdmi_safe=1

uncomment this if your display has a black border of unused pixels visible

and your display can output without overscan

#disable_overscan=1

uncomment the following to adjust overscan. Use positive numbers if console

goes off screen, and negative if there is too much border

#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

uncomment to force a console size. By default it will be display's size minus

overscan.

#framebuffer_width=1280
#framebuffer_height=720

uncomment if hdmi display is not detected and composite is being output

#hdmi_force_hotplug=1

uncomment to force a specific HDMI mode (this will force VGA)

#hdmi_group=1
#hdmi_mode=1

uncomment to force a HDMI mode rather than DVI. This can make audio work in

DMT (computer monitor) modes

hdmi_drive=2

uncomment to increase signal to HDMI, if you have interference, blanking, or

no display

#config_hdmi_boost=4

uncomment for composite PAL

#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

Uncomment some or all of these to enable the optional hardware interfaces

#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

Uncomment this to enable the lirc-rpi module

#dtoverlay=lirc-rpi

Additional overlays and parameters are documented /boot/overlays/README

Enable audio (loads snd_bcm2835)

dtparam=audio=on
gpu_mem_256=128
gpu_mem_512=256
gpu_mem_1024=256
overscan_scale=0

NOOBS Auto-generated Settings:

#hdmi_force_hotplug=1
hdmi_force_edid_audi=1
#hdmi_ignore_hotplug=1
sdtv_mode=2
dtparam=spi=on

mitu

@Paisano87 You seem to have enough GPU memory, which is a good thing. Check your VRAM Limit setting in Emulationstation and make sure you have more than 80 Mb allocated (try with 120Mb also). Restart Emulationstation after you change the settings and see if you get better results.

Paisano87

@mitu Where should I go to modify the VRAM changes? forgive for my ignorance ... thanks

mitu

@Paisano87 In the Emulationstation menus, activated by pressing Start.

Paisano87

@mitu Another way yo chance this?, in my emulationstation menu don't show this!, Only save metadata on exit and parse gameslist only

mitu

@Paisano87 Then you might be using an older Emulationstation version - you can check your version at the bottom of the menu, after you press Start . What version are you using ?

Paisano87

@mitu Hi, I'm using version 2.01A

mitu

@Paisano87 That is not supported by the theme - and by a lot of recent themes. Are you using RetroPie or not ?

Paisano87

@mitu said in SNES mini theme:

That is not supported by the theme - and by a lot of recent themes. Are you using RetroPie or not ?

Yes, i use retropie

mitu

@Paisano87 Then please use a recent version, your version is probably too old - or badly configured - and doesn't have a current version of Emulationstation.

Paisano87

@mitu
There is some way to update emulationstation without the need to re-record retropie?, is that I have a multiboot in the SD card and that would entail staying without the other systems
Thanks

mitu

@Paisano87 Sure, each package can be updated individually - https://retropie.org.uk/docs/Updating-RetroPie/#updatinginstalling-individual-packages. But your system might be so old that the update has a chance it would not work.

Paisano87

Try to update the package individually and it worked perfectly, I already have the theme applied !! Many thanks!!