Has anyone Gotten the Mayflash Gamecube Adapter to work with Retropie?

mediamogul

Not a problem. I had to work around a few other problems that were inherent with the Gamecube controller's analog control implementation. If you run into these issues as well, give me a shout. I may be able to help further.

hyawatha15

@mediamogul So funny thing.. I went through the steps and it's still stuck at connecting on port 0.

When I type: sudo systemctl status gamecube.service
I get: gamecube.service - Wii U Gamecube Adapter
Loaded: loaded (/etc/systemd/system/gamecube.service; enabled)
Active: active (running) since Wed 2016-09-14 1:10:15 UTC; 7min ago
Main PID: 402 (wii-u-gc-adapte)
CGroup: /system.slice/gamecube.service
└─402 /usr/local/bin/wii-u-gc-adapter

Sep 14 01:10:15 retropie wii-u-gc-adapter[402]: adapter 0x0x1146c48 connected
Sep 14 01:10:15 retropie wii-u-gc-adapter[402]: connecting on port 0

I can't control anything with the gamecube controller. The prompt to set the inputs isn't coming up either.

mediamogul

@hyawatha15

I might be misunderstanding you, but the 'Input Configuration' tool only shows up automatically on the first boot of the system. Any other time it has to be invoked by either the keyboard or another controller that you have already mapped. Assuming this is the issue, you would press whatever you have already mapped to 'Start' while in Emulation Station and the config option will be at the bottom of the resulting menu.

hyawatha15

@mediamogul

Interesting, I thought the input menu came up any time a new controller that hasn't been used before gets plugged in. I'll use a working controller to bring up the Input Configuration tool.

I assumed that because I was still seeing: Sep 14 01:10:15 retropie wii-u-gc-adapter[402]: connecting on port 0, I was stuck where I was at before. I'll update this post when I get home to try it.

tebra

@mediamogul said in Has anyone Gotten the Mayflash Gamecube Adapter to work with Retropie?:

@hyawatha15

Not a problem. I had to work around a few other problems that were inherent with the Gamecube controller's analog control implementation. If you run into these issues as well, give me a shout. I may be able to help further.

Hi mediamogul,
I follow your guide to use my Mayflash Gamecube adapter on my RetroPie v4.0.3 RPi3. Works good.
Only issue left are the analog controls (shoulders and sticks).
Any help/news about that?
Thanks

mediamogul

@tebra said in Has anyone Gotten the Mayflash Gamecube Adapter to work with Retropie?:

Only issue left are the analog controls (shoulders and sticks).

Are you trying to configure your triggers to be analog or digital? Personally, I would recommend digital in most cases, although analog is possible. Also, what exactly are the problems you're facing with the stick?

mediamogul

I might not be around later, so I thought I'd post the configs I use for my own adapter for you to use as a reference.

Analog Triggers:

sudo /opt/retropie/supplementary/xboxdrv/bin/xboxdrv \
	--evdev /dev/input/by-id/usb-raphnet.net_GC_N64_to_USB__v2.9_3918-event-joystick \
	--detach-kernel-driver \
	--force-feedback \
	--dpad-as-button \
	--deadzone-trigger 15% \
	--deadzone 4000 \
	--device-name "Raphnet Gamecube Adapter - Analog Triggers (xboxdrv)" \
	--silent \
	--calibration X1=-23436:0:26594,Y1=-25693:0:26593,X2=-20521:0:23068,Y2=-24890:0:19246 \
	--axismap -Y1=Y1,-Y2=Y2 \
	--evdev-absmap ABS_X=x1,ABS_Y=y1,ABS_RX=x2,ABS_RY=y2,ABS_RZ+=LT,ABS_THROTTLE+=RT \
	--evdev-keymap BTN_C=x,BTN_EAST=y,BTN_WEST=a,BTN_NORTH=b,BTN_TR=back,BTN_SOUTH=start,BTN_Z=lb,BTN_TL=rb,BTN_TL2=du,BTN_TR2=dd,BTN_START=dl,BTN_SELECT=dr \
	--ui-axismap start+x1=REL_X:10,start+y1=REL_Y:10 \
	--ui-buttonmap guide=void,tl=void,tr=void,start+lb=BTN_LEFT,start+rb=BTN_RIGHT

Digital Triggers:

sudo /opt/retropie/supplementary/xboxdrv/bin/xboxdrv \
	--evdev /dev/input/by-id/usb-raphnet.net_GC_N64_to_USB__v2.9_3918-event-joystick \
	--detach-kernel-driver \
	--force-feedback \
	--dpad-as-button \
	--trigger-as-button \
	--deadzone-trigger 15% \
	--deadzone 4000 \
	--device-name "Raphnet Gamecube Adapter (xboxdrv)" \
	--silent \
	--calibration X1=-23436:0:26594,Y1=-25693:0:26593,X2=-20521:0:23068,Y2=-24890:0:19246 \
	--axismap -Y1=Y1,-Y2=Y2 \
	--buttonmap LT=lb,RT=rb \
	--evdev-absmap ABS_X=x1,ABS_Y=y1,ABS_RX=x2,ABS_RY=y2,ABS_RZ+=LT,ABS_THROTTLE+=RT \
	--evdev-keymap BTN_C=x,BTN_EAST=y,BTN_WEST=a,BTN_NORTH=b,BTN_TR=back,BTN_SOUTH=start,BTN_Z=lb,BTN_TL=rb,BTN_TL2=du,BTN_TR2=dd,BTN_START=dl,BTN_SELECT=dr \
	--ui-axismap start+x1=REL_X:10,start+y1=REL_Y:10 \
	--ui-buttonmap guide=void,tl=void,tr=void,start+lb=BTN_LEFT,start+rb=BTN_RIGHT

tebra

@mediamogul said in Has anyone Gotten the Mayflash Gamecube Adapter to work with Retropie?:

@tebra said in Has anyone Gotten the Mayflash Gamecube Adapter to work with Retropie?:

Only issue left are the analog controls (shoulders and sticks).

Are you trying to configure your triggers to be analog or digital? Personally, I would recommend digital in most cases, although analog is possible. Also, what exactly are the problems you're facing with the stick?

I try to use my GC controler with reicast emulator.
But when I start /opt/retropie/emulators/reicast/bin/reicast-joyconfig it hang at "please move tha analog stick as far left as possible now"
So I suppose that default stick confioguration is not analog.

tebra

@mediamogul said in Has anyone Gotten the Mayflash Gamecube Adapter to work with Retropie?:

I might not be around later, so I thought I'd post the configs I use for my own adapter for you to use as a reference.

Analog Triggers:

sudo /opt/retropie/supplementary/xboxdrv/bin/xboxdrv \
	--evdev /dev/input/by-id/usb-raphnet.net_GC_N64_to_USB__v2.9_3918-event-joystick \
	--detach-kernel-driver \
	--force-feedback \
	--dpad-as-button \
	--deadzone-trigger 15% \
	--deadzone 4000 \
	--device-name "Raphnet Gamecube Adapter - Analog Triggers (xboxdrv)" \
	--silent \
	--calibration X1=-23436:0:26594,Y1=-25693:0:26593,X2=-20521:0:23068,Y2=-24890:0:19246 \
	--axismap -Y1=Y1,-Y2=Y2 \
	--evdev-absmap ABS_X=x1,ABS_Y=y1,ABS_RX=x2,ABS_RY=y2,ABS_RZ+=LT,ABS_THROTTLE+=RT \
	--evdev-keymap BTN_C=x,BTN_EAST=y,BTN_WEST=a,BTN_NORTH=b,BTN_TR=back,BTN_SOUTH=start,BTN_Z=lb,BTN_TL=rb,BTN_TL2=du,BTN_TR2=dd,BTN_START=dl,BTN_SELECT=dr \
	--ui-axismap start+x1=REL_X:10,start+y1=REL_Y:10 \
	--ui-buttonmap guide=void,tl=void,tr=void,start+lb=BTN_LEFT,start+rb=BTN_RIGHT

Digital Triggers:

sudo /opt/retropie/supplementary/xboxdrv/bin/xboxdrv \
	--evdev /dev/input/by-id/usb-raphnet.net_GC_N64_to_USB__v2.9_3918-event-joystick \
	--detach-kernel-driver \
	--force-feedback \
	--dpad-as-button \
	--trigger-as-button \
	--deadzone-trigger 15% \
	--deadzone 4000 \
	--device-name "Raphnet Gamecube Adapter (xboxdrv)" \
	--silent \
	--calibration X1=-23436:0:26594,Y1=-25693:0:26593,X2=-20521:0:23068,Y2=-24890:0:19246 \
	--axismap -Y1=Y1,-Y2=Y2 \
	--buttonmap LT=lb,RT=rb \
	--evdev-absmap ABS_X=x1,ABS_Y=y1,ABS_RX=x2,ABS_RY=y2,ABS_RZ+=LT,ABS_THROTTLE+=RT \
	--evdev-keymap BTN_C=x,BTN_EAST=y,BTN_WEST=a,BTN_NORTH=b,BTN_TR=back,BTN_SOUTH=start,BTN_Z=lb,BTN_TL=rb,BTN_TL2=du,BTN_TR2=dd,BTN_START=dl,BTN_SELECT=dr \
	--ui-axismap start+x1=REL_X:10,start+y1=REL_Y:10 \
	--ui-buttonmap guide=void,tl=void,tr=void,start+lb=BTN_LEFT,start+rb=BTN_RIGHT

So I can use virtual xboxdrv with ToadKing's driver?

mediamogul

@tebra

I accidentally posted my settings for the RaphNet Gamecube adapter. I'll have to dig up my configs for Mayflash after a while. Sorry for the confusion.

mediamogul

@tebra said in Has anyone Gotten the Mayflash Gamecube Adapter to work with Retropie?:

when I start /opt/retropie/emulators/reicast/bin/reicast-joyconfig it hang at "please move tha analog stick as far left as possible now"

If I remember correctly, I couldn't get reicast-joyconfig to read the analog stick either, but I'm almost certain you can just add the standard axis values to /home/pi/.reicast/emu.cfg and it will read them normally.

I believe the following are the two configs I used with the Mayflash adapter and ToadKing's driver:

Analog Triggers

/opt/retropie/supplementary/xboxdrv/bin/xboxdrv \
	--evdev /dev/input/by-id/usb-mayflash_limited_MAYFLASH_GameCube_Controller_Adapter-event-mouse \
	--force-feedback \
	--deadzone-trigger 15% \
	--deadzone 4000 \
	--device-name "Mayflash GameCube Port 1 (xboxdrv)" \
	--silent \
	--axismap -Y1=Y1,-Y2=Y2 \
	--evdev-absmap ABS_X=x1,ABS_Y=y1,ABS_RZ=x2,ABS_Z=y2,ABS_RX=LT,ABS_RY=RT,ABS_HAT0X=dpad_x,ABS_HAT0Y=dpad_y \
	--evdev-keymap BTN_TOP=x,BTN_TRIGGER=y,BTN_THUMB2=a,BTN_THUMB=b,BTN_BASE2=back,BTN_BASE4=start,BTN_TOP2=lb,BTN_PINKIE=rb

Digital Triggers

/opt/retropie/supplementary/xboxdrv/bin/xboxdrv \
	--evdev /dev/input/by-id/usb-mayflash_limited_MAYFLASH_GameCube_Controller_Adapter-event-mouse \
	--force-feedback \
	--trigger-as-button \
	--deadzone-trigger 15% \
	--deadzone 4000 \
	--device-name "Mayflash GameCube Port 1 (xboxdrv)" \
	--silent \
	--axismap -Y1=Y1,-Y2=Y2 \
	--buttonmap LT=lb,RT=rb \
	--evdev-absmap ABS_X=x1,ABS_Y=y1,ABS_RZ=x2,ABS_Z=y2,ABS_RX=LT,ABS_RY=RT,ABS_HAT0X=dpad_x,ABS_HAT0Y=dpad_y \
	--evdev-keymap BTN_TOP=x,BTN_TRIGGER=y,BTN_THUMB2=a,BTN_THUMB=b,BTN_BASE2=back,BTN_BASE4=start,BTN_TOP2=lb,BTN_PINKIE=rb

tebra

@mediamogul said in Has anyone Gotten the Mayflash Gamecube Adapter to work with Retropie?:

/dev/input/by-id/

Thank you for your config but I have a problem: my gamepad is not listed on /dev/input/by-id/
Here is the information given by "cat /proc/bus/input/devices" command
I: Bus=0003 Vendor=0000 Product=0000 Version=0000
N: Name="Wii U GameCube Adapter Port 1"
P: Phys=
S: Sysfs=/devices/virtual/input/input2
U: Uniq=
H: Handlers=event2 js0
B: PROP=0
B: EV=20000b
B: KEY=f 0 0 0 0 0 0 0 adb0000 0 0 0 0 0 0 0 0 0
B: ABS=3f
B: FF=50000 0 0

I: Bus=0003 Vendor=0000 Product=0000 Version=0000
N: Name="Wii U GameCube Adapter Port 2"
P: Phys=
S: Sysfs=/devices/virtual/input/input3
U: Uniq=
H: Handlers=event3 js1
B: PROP=0
B: EV=20000b
B: KEY=f 0 0 0 0 0 0 0 adb0000 0 0 0 0 0 0 0 0 0
B: ABS=3f
B: FF=50000 0 0

mediamogul

@tebra

You can also fall back on using the event numbers as well:

--evdev /dev/input/event2

--evdev /dev/input/event3

tebra

@mediamogul
Is it possible by N: Name="Wii U GameCube Adapter Port 1" and N: Name="Wii U GameCube Adapter Port 2".
Because if I reboot the rpi3 without my keyboard the event number will change. I'm right?

mediamogul

@tebra said in Has anyone Gotten the Mayflash Gamecube Adapter to work with Retropie?:

Is it possible by N: Name="Wii U GameCube Adapter Port 1" and N: Name="Wii U GameCube Adapter Port 2".

Sadly no. Those do not actually point to the events.

if I reboot the rpi3 without my keyboard the event number will change. I'm right?

I believe you're right. However, it might help to rearrange the order of your devices in relation to the USB slots to where the keyboard is always seen last.