Just made sure my RPI was up to date with latest scummvm binary and the opengl option worked ok here. Perhaps something else in your config - you could remove /opt/retropie/configs/scummvm and re-install from binary and see if that helps.

@BuZz said:

Why ? The wheezy version is no longer supported and you would be better off with 3.6 - if you have a problem with that version, perhaps we can help.

i have a 3.6 TFT, and it haven´t almost no support

the little information I've found is to install in raspbian wheezzy and not is support
for jezzy.

http://appdictive.dk/blog/projects/2015/10/30/cheap_tft_display_on_raspberry_pi/

@gutossn said:

I have the Retropie 2.6 for RP1. If you want, i can upload to you the img file from sd card (8GB). Google Drive. See ya.

i thank you very much, I appreciate it but I prefer to wait to see if I get a newer version

@Drakaen391 yes, by removing the p3 controller configuration from the ps3 controller configuration menu (same place where you installed it)

@mad61190 Yes, like I tought. That is your monitor that isn't passing the right info to the Raspberry/Kodi. A fix for that can only be made in Kodi program itself.

Is there needed to config the Controller again to play with the ROMs? I can control everything in Menu but if the ROM is starting than the Controller is not anymore working.

@caver01 said:

You should be able to get very good spinner support working in AdvanceMAME. I have an Ultimarc U-TRAK trackball and two (2) Groovy Game Gear TurboTwist 2s working perfectly in AdvanceMAME, but it took some messing around with the advmame.rc file to get it setup properly.

Check here:
https://retropie.org.uk/forum/topic/106/trackball-working-in-mame4all-but-not-advmame/2

That's awesome! I will give it a shot and let you know how it worked.

@herb_fargus I will try and see what happens o/

D'oh. Fixed it. Sorry. Didn't realize the whole network went south.

Thank you for all the assistance. I grabbed .78 and I'll use that instead. Any thing (MAMECLR) that you already state is difficult to use is probably NOT worth investing the time in for a one time setup for a quick mess around box attached to the TV. All I really wanted to do with my PI 3 was replace the HUGE 'media center' PC that has been taking up space in the living room with something that might play a couple of games and allow surfing on my slightly older app filled but not 'smart' TV.

Thank you again for the assistance and for all of your work on this project. I may tinker with it later and become proficient, but at this point I just want to plunk down and play some Galaga and Dig Dug. Thanks for the information on how to find out what is installed as default. I appreciate that as well.

You can't because it will not work even if it compiles properly. Use a PC.

@herb_fargus Much appreciated. All those menus look familiar. I'll try that - handy to know that I can have custom configs for each rom. Thanks!

I am able to get it working now on Emulation Station but on reboot it needs to be manually discovered again, I wrote the script that finds the MAC address and make sure it found but it does not seem to be working.

#!/bin/bash
sudo bluetoothctl << EOF
power on
connect [MAC Address]
exit
EOF

I made the correction and was given a prompt for a pin I set it to 0000
It seems to be working fine now

#!/bin/bash
sudo bluetoothctl << EOF
power on
connect [MAC Address]
connect [MAC Address]
exit
EOF

Would that be the only change to make two of the same controllers be found on boot?

This is exactly what I was looking for! Thank you for the clarification and fast response!

@Leo1372 In Kodi -> Settings -> Settings ->Peripherals

Kodi 16 + joysticks was tested in RetroPie 3.6. Keep in mind that if you update the RetroPie-Setup scripts and make a Binary based instalation, you will get the very latest changes to RetroPie, so not the same as installing a clean RetroPie 3.6 image.