@cyperghost yep, but the GitHub link references building it etc. I was just pointing out it's packaged already.

@jcthrity3 Anyone? Beuler? Beuler?

I understand that that would be the best solution, but the problem is that I have a lot of work in this sd card (ultrastar in raspbian) (libreelec totally configured with addons)
and other compilations of source do me correctly, the emulator version libreto I have it installed.
My options would be the following

1º Try to solve the error

/home/pi/RetroPie-Setup/tmp/build/mupen64plus/GLideN64/src/Log.cpp: In function ‘std::wstring getFormattedTime()’: /home/pi/RetroPie-Setup/tmp/build/mupen64plus/GLideN64/src/Log.cpp:38:9: error: ‘put_time’ is not a member of ‘std’

2º Configure lr-mugen64plus so that they load the textures in better resolution

3º try to import the binary in some way by ftp

Thank you very much for your time

a greeting

@caver01 said in Trackball working in mame4all but not Advmame??:

You definitely need to configure the controls in the advmame.rc file for trackball/spinner controls to work correctly in AvanceMAME. Look for these entries and correct them as follows:

device_mouse raw
device_raw_mousedev[0] /dev/input/mouse0
device_raw_mousedev[1] /dev/input/mouse1
device_raw_mousedev[2] /dev/input/mouse2
device_raw_mousetype[0] ps2
device_raw_mousetype[1] ps2
device_raw_mousetype[2] ps2

You want "raw" input capture for the mouse, and you want them set to "ps2". Depending on how your setup detects the devices, they may come in as Mouse0, 1, 2 etc. So, just set all of them this way.

Then, further down into the .rc file, you specify which input is used by MAME like this:

input_map[p1_trackballx] mouse[0,x] mouse[1,x] mouse[2,x]
input_map[p1_trackbally] mouse[0,y] mouse[1,y] mouse[2,y]
input_map[p1_dialx] mouse[0,x]
input_map[p2_dialx] -mouse[0,y]

You see how I have mouse 0, 1, and 2 all mapped in the trackball x and y? That's because, if I had an external mouse plugged in, my trackball might shift over to 1 instead of 0. Later, if I unplug the external mouse, it shifts back to 0. By specifying all three possibilities (I also have spinners), it doesn't matter--all of the mouse inputs map as a trackball.

The dial inputs are what advancemame calls the spinners. For my setup, mouse 0 was consistently my spinners. So, Player 1 would get the x-axis and player 2 would get the y axis, although I noticed that the y axis was spinning backwards, so I added the minus in front to reverse it.

Your setup will be different I am sure, but you should be able to get the inputs working this way. Once configured in the .rc file, you can play with sensitivity settings using the in-game MAME GUI.

One final note--the polling rate isn't fast enough by default. The trackball and spinners have way more resolution than was being captured causing a good fast spin to register as a backspin until it slows down. That can be very frustrating. You can increase the polling rate to fix this. Add: usbhid.mousepoll=2 to your /boot/cmdline.txt.

Thank you for this! I have spent 3 days trying to get this spinner to work. It's rocking now!

@ddallman said in Player 1 START button not working IN GAME - CPS1:

What could be the deal?

If the start button works everywhere except the cps1 games, i would expect the issue to be in mame2003's cps1 emulation ? However i don't think you'll get support for this emulator, using mame2003-plus or FBNeo is highly recommended nowaday. Also, FBNeo is supposed to provide the best experience with cps1/cps2 in terms of accuracy and input lag.

@icvaalmall84 It's not down, https://www.screenscraper.fr works fine.

@mitu welp, you solved my problem. So emulationstation if launched from c:\programfiles\emulationstation\emulationstation.exe it is v2.9.0RP-DEV which works fine. I originally set it to install in D:\emulationstation so the exe in that location launches v2.0.1A which I just realized I accidentally deleted my desktop exe and then went to that location to grab it again. Dont know why there are 2 locations but v2.0.1A is what causes a problem. Somehow when typing this I went to 2.9.0 without thinking to check the version and then just closed it but every time I tried to use a controller I was launching v2.0.1. Sorry and thank you ._.

Going to leave this up unless mods wanna delete it cause maybe others might make a dumb mistake like me.

@quicksilver @mitu

It worked! Thanks for the help!!!

@washburngopro

That might be run-ahead instances. I think the setting is found under "latency".
Could set it to zero, I never use it but it is okay with some Nintendo games.

The bios is good, you should keep it. Rarely (Arc the Lad Monster Tournament) do I ever have to use no bios.

If your pi doesn't have any heatsink, airflow, cooling fan, radiator. It will overheat and the SoC/CPU will throttle undermining performance in some games. While it is possible to underclock and increase the soft/temp limit to get adequate performance for PSX, good ventilation is still needed when playing 4+ hours.

MODERATION NOTE: I merged the 2 topics you opened. If you find your posts flagged as spam, try removing the code blocks first when posting.

The power supply im using is working fine i fixed that issue

The issues i keep running into keep changing
now for some reason when i try to set up the wifi country in the retropie settings i get an error saying "could not communicate with wpa_supplicant" and then it says "there was an error running option I4 change wifi country" what do i need to do to fix this issue? i believe it is because of this that the ethernet on the raspberrypi isnt being accepted either

I had this issue where a left mouse click would freeze any game that had a panel overlay (the side art around the actual gameplay). Here was a thread about it. It looks like its fixed on the newest version of Retroarch 1.7.7.

https://retropie.org.uk/forum/topic/16926/retroarch-cores-crash-on-trigger-press-mouse-click-with-overlay-active

Thank you very much @barbudreadmon and @mitu the game now creates the gng.hi and correctly saves the hiscores.

@simpleethat No worries mate thanks for your help.

It's good that this is documented so if it happens to somebody else they know how to fix it.

@JustinWagga said in SAMBA Can't get it working:

It was just a recommended fix I found by Googling.

I would rollback the changes in your Win10 install. What edition and version of Win 10 do you have ? I know some editions disable automatcally guest login.

@Sebiohazard Can you give me an example - a game that doesn't work ? The info might not be on the scraping site for that particular game.