@biccahobz123 have a look into mitus post. You are in KIDS-Mode and have to change back to normal ;)

@YFZdude I see. Thanks for the info and the tip. But the issue I have, and the reason I wanted for every button to work on d-input, is the fact that both controllers have the same name in switch mode, which is a problem with their wildly different layouts.

Update your EmulationStation package and try again.

@mitu This is just what I was looking for. I performed an update within retropie config and got the same result. couldn't access any setup menu. copying the ROMs and Bios over, but a couple of BIN files wouldn't copy (admin permission required). I guess after I reflash the SD card, this won't be a problem putting all my ROMs back?

@georgeio111 didn't you say:

.. I brought it approx 5 years ago with all games already on it. ..

This is one of the systems we don't support here in the forums - see https://retropie.org.uk/forum/topic/3/read-this-first.

@mitu I was able to set a system variable OS_NAME=RetroPie and re-ran the script from GIT and the install works now. Not 100% fully tested at this point but at least RetroPie sees the “New” controller

Here is the updated config.txt file

pi@retropie:~ $ cat /boot/config.txt # For more options and information see # http://rpf.io/configtxt # Some settings may impact device functionality. See link above for details # uncomment if you get no picture on HDMI for a default "safe" mode #hdmi_safe=1 # uncomment this if your display has a black border of unused pixels visible # and your display can output without overscan #disable_overscan=1 # uncomment the following to adjust overscan. Use positive numbers if console # goes off screen, and negative if there is too much border #overscan_left=16 #overscan_right=16 #overscan_top=16 #overscan_bottom=16 # uncomment to force a console size. By default it will be display's size minus # overscan. #framebuffer_width=1280 #framebuffer_height=720 # uncomment if hdmi display is not detected and composite is being output hdmi_force_hotplug=1 # uncomment to force a specific HDMI mode (this will force VGA) #hdmi_group=1 #hdmi_mode=1 # uncomment to force a HDMI mode rather than DVI. This can make audio work in # DMT (computer monitor) modes #hdmi_drive=2 # uncomment to increase signal to HDMI, if you have interference, blanking, or # no display #config_hdmi_boost=4 # uncomment for composite PAL #sdtv_mode=2 #uncomment to overclock the arm. 700 MHz is the default. #arm_freq=800 # Uncomment some or all of these to enable the optional hardware interfaces #dtparam=i2c_arm=on #dtparam=i2s=on #dtparam=spi=on # Uncomment this to enable infrared communication. #dtoverlay=gpio-ir,gpio_pin=17 #dtoverlay=gpio-ir-tx,gpio_pin=18 # Additional overlays and parameters are documented /boot/overlays/README # Enable audio (loads snd_bcm2835) dtparam=audio=on [pi4] # Enable DRM VC4 V3D driver on top of the dispmanx display stack dtoverlay=vc4-fkms-v3d max_framebuffers=2 [all] #dtoverlay=vc4-fkms-v3d overscan_scale=1 dtoverlay=picade dtparam=audio=off

I’ll give it another whirl, bit I don’t remember that working when I tried it.......thanks. @Crush

@DanTarl

Hi DanTarl - I created a forum account just to thank you for this tip.

I was frustrated by my zero delay encoder going in to disconnect/reconnect loop (led flashing) while using MAME on Ubuntu v22. Adding this to the Grub Linux boot parameters fixed the problem immediately.

The line now looks like this:

GRUB_CMDLINE_LINUX_DEFAULT="quiet splash usbhid.quirks=0x0079:0x0006:0x00000400"

Detailed instructions for editing Ubuntu boot parameters here.

Thanks again - solving this seemed like such a longshot!

Paul

@saku00 so I tried some Naomi 2 games on the standalone flycast on a pi4 2gb. Good news and bad.

They boot. But they're absolute slide shows. 4-7 FPS at best.

https://ibb.co/fvXsjwn - you can see the FPS counter in the corner. So I would say Naomi2 is a no for a pi4. Not surprising given they're basically PS2/GameCube/Xbox graphic games. Maybe a pi5 or 6 in a few years will be able to handle that.

@lostless Thanks. I actually figured it out. There's a custom config setting on the bottom left. If you select it for every game, it won't affect others. Just never noticed it before!

@g4h The latest version of RetroPie 4.8, is working with all revisions of RPi4.

@CapNinja I have this same error button all the emulators I use. Did you happen to fix this?

@windg well, the ScummVM RP documentation is not aligned with the implementation. And it will create a clutter in the scummvm/ folder, plus will rewrite the *.svm files everytime after exiting ScummVM, which is surplus.

This and the missing interop with the LR variant made me to have a design which creates a more "it just works" experience for the user.

@jameelperkins31 Then please open a separate topic and describe your issue, adding the info asked in https://retropie.org.uk/forum/topic/3/read-this-first, instead of replying to random topics in the forum.

@g2000 hello @g2000 I'm Jameel Perkins Asking IS It possible For u to help me by watching this video please I Really Wanna try to see if I can get across to play GameCube N Wii games

?

If this is a bug, maybe the new version of RetroPie will not have this. You can try and to rename the save file (back-up first) with the name of disk2 and boot the game directly from there

The most multi disk games that i have try they don't have issue, only in few games disk swap is tricky.

If the issue continue you can report it directly to the developer of emulator here: https://github.com/libretro/pcsx_rearmed/issues

You can try also the alternative psx emulator, from RetroPie- Extra repo, lr-duckstation or lr-swanstation from here : https://github.com/Exarkuniv/RetroPie-Extra

@IsabelleXL SOLVED my using my keyboard as a USB hub

@Crush That is also an option, but sometimes I'd rather get everything scraped on a separate hard drive. Just makes me feel more secure in various ways. I'm probably just silly.