Had to remove your account as it was still sending out notifications.

Great news guys its up and running thank you very much for all your help and knowledge now its time for the dreamcast.

thanks

No, not currently something that is supported.

Check these threads for development suggestions:
https://retropie.org.uk/forum/topic/2250/emulationstation-fork
https://retropie.org.uk/forum/topic/4430/using-videos-in-emulation-station/
https://retropie.org.uk/forum/topic/3121/emulationstation-mod
https://retropie.org.uk/forum/topic/3566/grid-view-emulationstation-mod-ideas

When you say "shoulder" buttons do you mean "trigger" buttons? Trigger buttons are the back left & right buttons that kinda look like gun triggers. The front left & right buttons like what's on the SNES controller are shoulder buttons (I actually think they are called "bumper" buttons on the 360 controller).

The Xboxdrv doesn't work with the latest kernel so you can downgrade your kernel to get it to work.

The xpad driver has a special trigger patch that fixes those left and right trigger buttons to work with EmulationStation but breaks support for Kodi.

@CaelThunderwing I updated the firmware and I have setup the controller in both regular mode and the xinput mode. I have both modes working for es and libetro cores. I'm trying to map the values of jstest and evtest to the keymaps for kodi.

Put the post as "Solved" plz ;D

ufff, what about to use a 64 gbs SD card?

Anyway maybe you could try to copy and paste files with putty or WinSCP, care, you will need to be root, you will see all files that samba doesnt show up

@suprjami great thanks, this will help me a lot.

@dankcushions Great dude. I was working on something similar, I have about 50 configs done, but with artwork on the sides also(for verticals on horizontal). Wow 1500, you must have seperated verticals and wrote a bat file? And yes, I will use these for my long list lol, great place to start. What would be the easiest way to match these file names to my rom files names to seperate? I need like something that will remove all roms that dont have the same name or something. Somekind of match prog

@obsidianspider said in Boot Problems with Pi 3:

Running a Fan from GPIO can cause issues as they tend to draw quite a bit of current. If you have a spare SD card, try using that to see if it works before you reformat your existing SD card.

Its a really tiny fan, like the smallest you can buy, smaller than a quarter.

Anyway, I tried a spare sd card and put the newest retropie image on it with the fan and led plugged in and booted up fine, still does the text then splash then text again then into emulation station but quickly and with no issues. Never use to see the text twice, only once before the splash screen, must be new?

I guess my other sd card is corrupt somehow now.

@MennoSteenwijk said in Best raspberry pie for retropie:

After installing Retropie on my Raspberry pie 1 I encounterd some issues in the speed of the pie while trying to play for example Mario Kart N64

On the wiki, it says:
Note that you need a Raspberry Pi 2 if you want any decent N64 performance and even then it is hit and miss.
https://github.com/retropie/retropie-setup/wiki/Nintendo-64

Just arrived to RetroPie and still trying to configure my devices, after reading full topic here are my two cents:

unistalled PS3 Driver (clone) Paired Sony official PS3 bluetooth controller successfully Installed PS3 Driver (clone) Connect PS3 Clone Gamepad on USB then disconnect Push PS button to connect Gamepad. All done :)

At this point two devices works properly. I can change from retorpie to kodi and back again and all its fine. Just played some games on joypad, exit retropie onto kodi, navigate using keyboard.. all fine !

But... after reboot, bluetooth keyboard can't be paired again. I need to start over again from point 1.

the question is: It's possible on boot process, disable sixaxis while normal stack connects to bluetooth keyboard (or other devices) and after some time (maybe 1 minute) reenable sixaxis again?
How is started bluetooth device during boot? and where are the scripts?

Any advice are welcome if someone has tryed something like this.

Obocaman

@OldDucGuy I just run the parent

@Floob yeah i'v always used the crt pi shader, love it. but all those overlays, they're so.. cosy! Nostalgia is one helluva drug.

Another step forward! These are my controllers default calibration values:

jscal -s 18,1,0,112,142,5534751,5534751,1,0,112,142,5534751,5534751,1,0,112,142,5534751,5534751,1,0,112,142,5534751,5534751,1,0,112,142,5534751,5534751,1,0,112,142,5534751,5534751,1,0,0,0,536870912,536870912,1,0,0,0,536870912,536870912,1,255,-4208,3952,21931,21931,1,255,-4208,3952,21931,21931,1,255,-4208,3952,21931,21931,1,63,-1023,1023,87367,87367,1,63,-1023,1023,87367,87367,1,63,-1023,1023,87367,87367,1,0,0,0,0,0,1,0,960,960,559240,559240,1,0,471,471,1139853,1139853,1,0,32767,32767,16384,16384 /dev/input/js0

And this pacifies the gyroscope's axis. I don't need them and they cause endless events if not "deadzoned":

jscal -s 18,1,0,112,142,5534751,5534751,1,0,112,142,5534751,5534751,1,0,112,142,5534751,5534751,1,0,112,142,5534751,5534751,1,0,112,142,5534751,5534751,1,0,112,142,5534751,5534751,1,0,0,0,536870912,536870912,1,0,0,0,536870912,536870912,1,255,0,0,0,0,1,255,0,0,0,0,1,255,0,0,0,0,1,255,0,0,0,0,1,255,-0,0,0,0,1,255,0,0,0,0,1,0,0,0,0,0,1,0,960,960,559240,559240,1,0,471,471,1139853,1139853,1,0,32767,32767,16384,16384 /dev/input/js0

Unfortunately there is no way to calibrate /dev/iput/event0, but /dev/input/js0 (jstest /dev/input/js0) is completely silent now if the gamepad isn't in use. This should be good enough for me, as even SDL might be forced to use /dev/input/js0 (export SDL_JOYSTICK_DEVICE=/dev/input/js0).

Next step would be to recognize for how long /dev/input/js0 showed no action. Any ideas?