Look for the .rc file at /opt/retropie/configs/mame-advmame

But be careful. Changing the .rc file is tricky and a can result in a failure to boot into advmame.

@quicksilver I have 6 button setup working on both emulators as of now. I found the settings you mentioned in Mortal Kombat II but changing them made no difference. I went over everything on my setup and was stumped. I booted up a fresh image, completely up to date, configured my SNES and Xbox controllers and put on my Sega games only. I made the changes to the respective config files and presto it works. After changing the setting you pointed out that I missed earlier in Mortal Kombat. I don't know why my original setup was not working. It has to be something I modified but I haven't found it. Thanks for you help and if I track it down I'll let you know.

Update: I think I found the problem. When I updated in the morning I did both binary and source, I've never used source before. It wrecked my controller configurations. It had my generic SNES listed as generic and just SNES, and the Xbox controllers were listed as generic Xbox, the original config, and Xbox 360 Pro. Every game I launched listed the two controllers I had connected twice and then worked in piece. Not sure why updating from source would do this as I have updated from binary and it was fine. In the future I will probably unplug all controllers and use the keyboard for updating.

@retronoobie3000 I know this does not help DosBox but malcolm's Revenge runs flawlessly in scummvm.

@mike001 issue is resolved don't know why but I repeatedly paired and it finally showed up.

@spider910 For my project, I simply made my own using Cat5 wiring. This allowed me to cut an exact length, kept everything nicely bundled inside the insulation, and made it very easy to know which wire was going where as opposed to everything black which would be a bit of a visual nightmare. I simply crimped on my own spade-type connectors to mate with the microswitches (most arcade parts sellers sell these in bulk, or easily found at hardware stores). The encoder end for me uses screw terminals (IPAC) so this was ideal, but I could have added header connectors too.

I don’t have any experience with this particular setup. But do you need to be root user to make these changes? Being logged in as root has changed permissions in the past for me that broke my setup pretty bad.

Maybe you can run the utilities with sudo as user Pi and see if that changes the outcome. I may be way off base. I’d love to see the results of this on a CRT when finished. Good luck

@bogus You can save the relevant part from the configs for the overlay part, they should be easy to re-apply - https://retropie.org.uk/docs/Configuration-Editor/#advanced-configuration

@robmcc83 Only if it's supported by the emulator - but it doesn't seem so.
There is a libretro core for Vice (C64 emulator - port of VICE for libretro) in the experimental packages section, you could try and install it.

@cyber92 What does 'not working' mean ? What files did you copy and what game are you trying ?

Make sure the .bin filename is correct and corresponds to the name in the .cue file. Linux is case sensitive so make sure it's the same name both for the on-disk .bin file and the file declared in the .cue - see https://retropie.org.uk/docs/PC-Engine/#pc-engine-cd for an example.

@cyber92 Create a new topic, but I suggest searching the forums first for a similar problem and reading the PS1 page in the docs - https://retropie.org.uk/docs/Playstation-1/.

@myquyen1996 https://github.com/RetroPie/RetroPie-Setup/wiki/Stratagus

@sam Setting up RetroPie on a real RPi is easy if you follow the instructions (which you've presumably already looked at when you installed on Ubuntu), and the forums are full of extremely useful information (sometimes better than the documentation :P)

Have realistic expectations tho; while the vast majority of platforms are emulated pretty much flawlessly and PS1 emulation is mostly very good if you overclock your Pi a bit, N64 and Dreamcast are really at the very limit of what can be achieved on the Pi3.

If you're cool with that, and maybe asking a question or two here if/when you get stuck, then in my opinion there's no reason not to get an RPi3.

@rjotter Generally folks here don't like to help those who are using a pre-made SD image as the best source of help tends to the person who setup that image because who knows what they did with all the configs and setup.

BUT... you may need to look into using the xboxdrv?
https://github.com/RetroPie/RetroPie-Setup/wiki/Universal-Controller-Calibration-&-Mapping-Using-xboxdrv

I experimented with it at one point but never got it to solve my input issues. Turns out there were simpler issues at hand.

There is also this: http://blog.petrockblock.com/forums/search/?bbp_search=steam

I wonder if I was able to make a list of the games I need the USA region art for that maybe someone could make me a zip?

@mitu So I'm guessing I need to do a whole new install of retropie and emulation station then?
Thats what I was trying to avoid :(

@mitu perfect, thank you for the reply. I will check out the link and see what I can figure out. The audio devices don't need pins.

Thank you

Did you read the documentation?