@dankcushions Thanks a lot, my Problem is solved :-) :-)

@Smashpwn said in Games exit on there own.:

I also use a 2v power supply.

Nothing will work. You need 5V. Do you mean 2A? If so, you need 2.5A for a Pi3. You have failed to provide the essential information listed in https://retropie.org.uk/forum/topic/3/read-this-first so no further assistance is meaningful or possible.

@GreenHawk84 Thanks. I'll try that.

@SkittleBrau79 said in Emulation Station does not quit to command prompt:

I've solved this. Still not sure what the cause was... but doing a full update of all installed packages corrected it.

I had this in the beginning. How many roms have you got installed? Take a look at this:
https://github.com/retropie/retropie-setup/wiki/FAQ#why-does-shut-down-and-reboot-take-ages
Could be related?

@dolfan1994 ok. By the way, to be clear, the file is supposed to be either under configs->all->emulationstation or something like that. I can't exactly remember where, but if you get stuck I can check.

@Fultos so the d-pad is hats on the 8bitdo here is the config from the 8-bitdo. not sure if you can use h0 up down left right's on the coleco. here is the config from the 8-bitdo

input_up_btn = "h0up" input_down_btn = "h0down" input_left_btn = "h0left" input_right_btn = "h0right"

i will try to test tomorrow

Try a different adapter. That MayFlash didn't work on my two 3-button's, and only only a select amount of my 6-button controllers (maybe a little over half of them).

@rbaker said in Wired to NO instead of NC:

@domodan I thought that the terminals on the control block were screw terminals for buttons. If you are referring to the fact that you have soldered wires directly to the normally closed terminals of the micro switches inside your arcade buttons then no, you must de-solder and attach them to normally open otherwise they will all appear as permanently pressed. Why are you soldering at all? Crimp for the button contacts and terminal blocks for control block?

I'm a fan of solder over crimping and spade connectors. I don't have the right size spade connectors...the ones I have are too big. Solder works great...if you connect it to the right terminal. LOL. I was so excited I wasn't paying close enough attention for a second.

@demost Have you looked into @Floob and his Attract Mode Retropie image?

Obvs has no bundled rooms, but has Attract Mode as its main front-end rather than ES?

That should give you a more Hyperspin feel, no?

I see, well thank you for your time.

@Xyb0t glad you got it working good now.

@macothal you need to install the dosbox emulator as it doesn't come pre-installed with the image from the website.

Do that, restart EmulationStation and it'll all be good.

@markyh444 Thanks a bunch! I read through it and it does look very tricky. I'm thinking it may just be easier to do a fresh install to be on the safe side. Thanks again!

Many ways!

A power supply with a switch on so you can power down the unit after you've done your safe shutdown.

Power the fan from the USB port so that it goes of with the Pi.

One of these circuits that will shut off the power to the whole device a couple of minutes after the shutdown is initiated (although you might need a new case):

https://www.msldigital.com (they have a riser cable to get it away from your fan too)

http://mausberry-circuits.myshopify.com/collections/frontpage

https://lowpowerlab.com/shop/product/91

@tonydotigr All of the information on the I-PAC applies to the Mini-PAC. So you will have a default setup that is ready to use with MAME. Anything else will require you to reconfigure the controls on a per emulator basis or go and adjust the default configuration in hardware.

Old topic, but it's the one I found via Google after spending some time trying to figure out how to easily launch DOSBox games. Tried to follow both guides, but seemed very manual and finicky so ended up scripting it for my own Pie3 instead - basically it just takes an extracted copy of the game and allows you to select the executable and that will be saved to an init-file. Put it up on github if anyone wants it (https://github.com/tebl/retropie-dosbox-configure).

Ok have the audio working now. Last issue I have is that my usb Retro NES remote is all messed up. ie, b and a buttons are switched, select is starts. This causes issues when I cannot hold select and start to exit game. The remote works fine in other rom games except the NES. I have tried setting up several time in the input game pad set up and all worked fine on that